南水北调中线总干渠藻类的生态调度

南水北调中线总干渠无在线调蓄水库,对藻类生态调度过程中出现的问题开展生态调度实现策略和实施方式研究。主要实现策略包括:划定自身的调蓄区,隔离生态调度对下游的影响;采用高效的渠池运行方式,减少生态调度时蓄量的反复调整;综合考虑安全、快速、平稳等需求,设定生态调度实施进程和方式。具体实施方式包括:将总干渠划分为流速调控区、调蓄区和正常运行区,分别实施等体积、控制蓄量和闸前常水位方式运行;将生态调度过程划分为充水阶段和泄水阶段,基于流速调控目标值、持续时长和水位降幅约束条件,确定各阶段时长和各分区的闸门群调控方案等。基于2018年3月输水工况,采用明渠一维非恒定流模型,仿真总干渠上游15个渠池的藻类生态调度过程。结果表明,生态调度可在3.5 d内完成,各渠池的平均流速由0.48 m/s增至0.93 m/s,持续时间超过2 h。在整个生态调度过程中,水位变化平稳,水位变幅符合安全阈值要求,下游渠道的正常运行未受生态调度明显影响。     

Application of artificial neural network method to predict the breakage properties of PGE bearing chromite ore

In the present investigation, systematic grinding experiments were conducted in a laboratory ball mill to determine the breakage properties of low-grade PGE bearing chromite ore. The population balance modeling technique was used to study the breakage parameters such as primary breakage distribution (B_{i, j}) and the specific rates of breakage (S_i). The breakage and selection function values were determined for six feed sizes. The results stated that the breakage follows the first-order grinding kinetics for all the feed sizes. It was observed that the coarser feed sizes exhibit higher selection function values than the finer feed size. Further, an artificial neural network was used to predict breakage characteristics of low-grade PGE bearing chromite ore. The predicted results obtained from the neural network modeling were close to the experimental results with a correlation of determination R² = 0.99 for both product size and selection function.     

Catalysts by pyrolysis: Direct observation of transformations during re-pyrolysis of transition metal-nitrogen-carbon materials leading to state-of-the-art platinum group metal-free electrocatalyst

Transition metal-nitrogen-carbon (M-N-C) materials have been the focus of scientists’ efforts to address the rising need for earth-abundant materials solutions for energy technology and decarbonization of the economy. They are viewed as one of the most promising candidates to replace platinum group metal (PGM) catalysts in the fuel cell and energy conversion fields, including the application of oxygen reduction reaction, carbon dioxide reduction reaction, and nitrogen reduction reaction. In the effort to improve M-N-C materials properties and achieve atomic dispersity of the transition metal in the carbonaceous matrix, a re-pyrolysis process has been proposed. This secondary heat treatment process of already obtained primary pyrolysis-derived M-N-C materials has been widely reported to substantially improve the electrochemical performance and operational stability of the catalysts. Here, we report a systematic investigation of this process used on samples of templated M-N-C catalysts to obtain state-of-the-art catalysts via in situ heating X-ray photoelectron spectroscopy (XPS), scanning transmission electron microscopy (STEM), energy-dispersive X-ray spectroscopy (EDS), electron energy loss spectroscopy (EELS), X-ray diffraction (XRD), and X-ray computed tomography (CT) characterization methods. It is found that the re-pyrolysis of M-N-C materials could result in the partial amorphization of the carbonaceous substrate. It causes the rearrangement and transformation of multitudinous N moieties, leading to optimization of their morphological display and association with atomically dispersed transition metal dopants. Ultimately, the re-pyrolysis results in an increase in uniformity of the active Fe-N_x sites distribution without the formation of nano-crystalline phases (metallic or carbide) and with overall preservation of the morphology of the carbonaceous framework achieved during the first formative pyrolysis step of the templated synthesis. These observations provide confirmation that empirically established re-pyrolysis is recommended to be used on all M-N-C materials despite the different synthesis routes to obtain a practical advanced catalytic material.     

计及RSC控制的DFIG短路电流直流分量解析表达

现有文献针对计及转子变流器(RSC)控制的双馈感应风电机组(DFIG)定子短路电流解析表达,将定子磁链当作一阶直流衰减分量或忽略功率外环控制。基于DFIG电压、磁链和RSC控制方程,得到定子电流关于定子电压和定子功率的传递函数,提出定子电流的精确解析表达式。基于RSC内、外环PI参数关系,推导直流分量衰减时间常数和角频率关于PI参数的表达式。分析了RSC内外环PI参数对定子电流直流衰减分量的影响。仿真结果验证了解析表达式的准确性,为PI参数选取和保护装置测量、整定提供依据。     

基于CDIO工程教育的应用型人才培养 理论与实践研究 — —以红外多路遥控系统设计为例

The construction of specialty groups in higher vocational colleges is in full swing. However, due to the cognitive bias and the lack of construction paradigm for reference, the construction of specialty groups is still in the period of "crossing the river by feeling the stones" with different opinions. There are some problems in the construction of specialty groups, such as unclear under- standing of the concept of specialty groups, unreasonable logic of groups, unclear construction of groups, and nonstandard manage- ment of groups. This paper describes the specific content of the construction of modern information technology specialty group based on the Sydney Agreement, hoping to form a reference paradigm for the construction of specialty group of similar colleges and universities.     

Systematic convergence of nonlinear stochastic estimators on the Special Orthogonal Group SO(3)

This paper introduces two novel nonlinear stochastic attitude estimators developed on the Special Orthogonal Group with the tracking error of the normalized Euclidean distance meeting predefined transient and steady‐state characteristics. The tracking error is confined to initially start within a predetermined large set such that the transient performance is guaranteed to obey dynamically reducing boundaries and decrease smoothly and asymptotically to the origin in probability from almost any initial condition. The proposed estimators produce accurate attitude estimates with remarkable convergence properties using measurements obtained from low‐cost inertial measurement units. The estimators proposed in continuous form are complemented by their discrete versions for the implementation purposes. The simulation results illustrate the effectiveness and robustness of the proposed estimators against uncertain measurements and large initialization error, whether in continuous or discrete form.     

气动弹片对垂直轴风力机性能影响研究

片对垂直轴风力机气动性能的影响并分析了其流动机理。结果表明：气动弹片在高尖速比下可显著抑制流动分离并改善其动态失速特性，功率系数得到极大提升；切向力和转矩系数在气动弹片作用相位角范围内，均有一定提高，而在其它相位角内，风力机性能不受影响。     

Leading edge erosion of wind turbines: Effect of solid airborne particles and rain on operational wind farms

Leading edge erosion (LEE) affects almost all wind turbines, reducing their annual energy production and lifetime profitability. This study presents results of an investigation into 18 operational wind farms to assess the validity of the current literature consensus surrounding LEE. Much of the historical research focuses on rain erosion, implying that this is the predominant causal factor. However, this study showed that the impact of excessive airborne particles from seawater aerosols or from adverse local environments such as nearby quarries greatly increases the levels of LEE. Current testing of leading edge protection coatings or tapes is based on a rain erosion resistivity test, which does little to prove its ability to withstand solid particle erosion and may drive coating design in the wrong direction. Furthermore, it was shown that there is little correlation between test results and actual field performance. A method of monitoring the expected level of erosion on an operational wind turbine due to rain erosion is also presented. Finally, the energy losses associated with LEE on an operational wind farm are examined, with the average annual energy production dropping by 1.8% due to medium levels of erosion, with the worst affected turbine experiencing losses of 4.9%.     

Numerical study of a concept for major repair and replacement of offshore wind turbine blades

Repair and replacement of offshore wind turbine blades are necessary for current and future offshore wind turbines. To date, repair activities are often conducted using huge jack‐up crane vessels and by applying a reverse installation procedure. Because of the high costs associated with installation and removal of offshore wind turbine components and the low profit margin of the offshore wind industry, alternative methods for installation and removal are needed. This paper introduces a novel concept for replacement or installation of offshore wind turbine blades. The concept involves a medium‐sized jack‐up crane vessel and a tower climbing mechanism. This mechanism provides a stable platform for clamping, lowering, and lifting of a blade. A case study of a 5‐MW offshore wind turbine is shown, where common engineering practices were applied and numerical simulations of the marine operations were carried out using finite element and multibody simulation tools. Operational limits for wave and wind actions were established to demonstrate the technical feasibility of the proposed concept.