Impact of TiO2 nanoparticles and nanowires on corrosion protection performance of chemically bonded phosphate ceramic coatings

The impact of the addition of TiO₂ nanoparticles and nanowires on the morphology, phase characteristics, contact angle, and electrochemical performance of chemically bonded phosphate ceramic coatings (CBPCs) was investigated. The chemical composition and surface morphology of the TiO₂ nanoparticle and nanowire modified with and without (heptadecafluoro-1,1,2,2-tetradecyl) trimethoxysilane were characterized. Results indicated that the hydrophobic –CF₂– and –CF₃ groups were successfully introduced into the TiO₂ nanoparticles and nanowires after modification. Corrosion resistance of CBPCs with TiO₂ was evidently improved compared with that without TiO₂. Such improvement was mainly due to the combined effects of low surface energy materials and micro/nano structures. In addition, CBPCs with TiO₂ nanowires exhibited higher hydrophobicity and corrosion resistance than those with TiO₂ nanoparticles because of the special columnar structure of the nanowires.     

Application of artificial neural network method to predict the breakage properties of PGE bearing chromite ore

In the present investigation, systematic grinding experiments were conducted in a laboratory ball mill to determine the breakage properties of low-grade PGE bearing chromite ore. The population balance modeling technique was used to study the breakage parameters such as primary breakage distribution (B_{i, j}) and the specific rates of breakage (S_i). The breakage and selection function values were determined for six feed sizes. The results stated that the breakage follows the first-order grinding kinetics for all the feed sizes. It was observed that the coarser feed sizes exhibit higher selection function values than the finer feed size. Further, an artificial neural network was used to predict breakage characteristics of low-grade PGE bearing chromite ore. The predicted results obtained from the neural network modeling were close to the experimental results with a correlation of determination R² = 0.99 for both product size and selection function.     

Thermal shock effects on the impact resistance,tolerance and flexural strength of alumina based oxide/oxide ceramic matrix composites

In this study the effects of thermal shock on the impact damage resistance, damage tolerance and flexural strength of Nextel 610/alumina silicate ceramic matrix composites were experimentally evaluated. Composite laminates with balanced and symmetric layup were gradually heated to 1200°C in an air-based furnace and held for at least 30 min before being removed and immersed in water at room temperature. The laminates were then subjected to low velocity impacts via a hemispherical steel impactor. The resultant damage was characterized non-destructively, following which the laminates were subjected to compression tests. Three-point bend tests were also performed to evaluate the effect of thermal shock on the flexural strength and related failure modes of the laminates. Thermally shocked laminates showed smaller internal damage and larger external damage areas in comparison to their pristine counterparts. For the impact energy and resultant damage size considered, the residual compressive strengths for the thermally shocked and pristine laminates were similar.     

Dry Fractionation Approach in Concentrating Tocopherols and Tocotrienols from Palm Fatty Acid Distillate: A Green Pretreatment Process for Vitamin E Extraction

Palm fatty acid distillate (PFAD) is a rich source of vitamin E. As compared to other vegetable oil, PFAD has higher tocotrienol (70–80%) over tocopherol content, which makes it a valuable source for vitamin E extraction. Current vitamin E extraction methods are not sustainable due to the intensive usage of chemical and high operational cost. Hence, the present study investigated for the first time using dry fractionation process as a green and economical pretreatment method for separating solid fraction (stearin) and liquid fraction (olein) in order to concentrate vitamin E from PFAD in olein fraction. We examined the dry fractionation conditions: crystallization ending temperature (36–44 °C), cooling rate (0.3 and 1.5°C min⁻¹), stirring speed (20–125 rpm), and holding time (0–60 min) on the composition of unsaturated and saturated fatty acids as well as vitamin E content in liquid fraction (olein) and solid fraction (stearin) using gas chromatography and high performance liquid chromatography, respectively. In most of these conditions, vitamin E was ultimately higher in olein fraction as compared to stearin fraction, which is correlated with the high degree of unsaturation. Under a cooling rate of 0.3°C min⁻¹, 90 rpm stirring speed, and ending crystallization of 38 °C, the highest vitamin E rich olein fraction was attained with 1479 ± 10.51 ppm in 50 g olein fraction as compared to 1366 ± 7.94 ppm in 500 g of unfractionated PFAD.     

Investigation of the microwave dielectric properties of the Li4x/3Zn2−2xTi1+2x/3O4 system by P–V–L theory and vibration spectroscopy

Li_4x/3Zn_2–2xTi_1+2x/3O₄ microwave dielectric ceramics with a spinel phase were prepared via a high-temperature solid-phase method. P–V–L theory, vibration spectra, and XPS were utilized to establish the links between the intrinsic and extrinsic factors and the microwave dielectric properties. According to the characterization, the change in permittivity (ε_r) was ascribed to the increase in the average bond ionicity of Ti–O(Af_iTi-O) and the polar mode of the lattice vibration; the change in quality factor(Q × f) resulted from the change in the Ti–O lattice energy (AU_Ti-O) and existence of oxygen vacancy; the increase in temperature coefficient of the resonance frequency (τ_f) was triggered by the increase in the Ti–O bond energy. The Li_0.6Zn_1.1Ti_1.3O₄ ceramics (x = 0.45) sintered at 1125 °C finally obtained optimal microwave dielectric constants of ε_r = 17.3, Q × f = 76,318 GHz and τ_f = -58 ppm/°C.     

Growth mechanism and gas-sensing characteristics of organic-additive-free zinc oxide of various shapes

Zinc oxide is widely used in gas sensors, solar cells, and photocatalysts because of its wide bandgap and exciton binding energy of 60 meV in various metal oxides. To use ZnO as a gas sensor, it is necessary to synthesize it with surface defects and a large specific surface area. In this study, hydrothermal synthesis without surfactants was employed to obtain organic-additive-free ZnO. For morphology control, we varied the ratio of the hydroxide ion concentration to the zinc ion concentration. To confirm the growth mechanism of ZnO, we performed X-ray diffraction, scanning electron microscopy, and transmission electron microscopy analyses. Raman spectroscopy and photoluminescence measurements were performed to analyze the surface properties. The Brunauer–Emmett–Teller method and probe stations were used to measure the specific surface area and sensitivity of the gas sensor, respectively. The results confirmed that flower-shaped ZnO is the most suitable gas-sensing material.     

Do economic regulatory agencies matter to private-sector involvement in water utilities in developing countries?

This paper suggests that, for developing countries, the creation of economic regulatory agencies, separate from the ministry in charge of water and sanitation, may not be a necessary or sufficient condition to stimulate large scale private involvement (PPPs) in the sector. The odds of an impact are higher for Latin American countries than other regions and for countries with higher income levels. They are also better when inflation is high. At the margin, the odds are unrelated to the contract type, except for greenfield projects, for which they may be contraindicated.     

一种基于全变分技术和Lp伪范数的椒盐噪声去除方法

针对传统各向同性全变分（Isotropy total variation，ITV）去噪算法容易导致图像边缘模糊、不易保持图像细节信息等问题，提出一种基于L _p 伪范数和各向同性全变分的图像去噪方法。该方法将L _p 伪范数代替ITV模型中的L ₁范数，利用交替方向乘子算法（Alternating direction method of multipliers, ADMM）将能量泛函拆解成若干个子问题，并将差分算子视为卷积算子；然后引入卷积定理和快速傅里叶变换(Fast Fourier transform, FFT)提高算法运算效率；最后通过Matlab进行仿真实验，运用图像质量的客观和主观评价方法进行评价分析。结果表明，本文方法能够较好地保留图像的边缘特性，有效提升去噪效果。     

The alginate fermentation strain Pantoea sp. F16-PCAi-T3P21 and ethanol production

Bio-ethanol production from algae is a promising way to help solve the energy problem. Alginate is a major component of algae, but it cannot be utilized by existing ethanol fermentation microorganisms. In order to improve the utilization rate of brown algae, high alginate fermentation strains should be obtained. In this research, strains for algae fermentation were got from several experiments. The ethanol yield of strain A was the highest, which was 0.095 g/g (ethanol to alginate). The identification of strain A was carried out and it was 99% identical to Pantoea sp. F16-PCAi-T3P21. Fermentation experiments with different substrates were carried out, such as laminaran, mannitol, L. japonica and acid hydrolysate of L. japonica, and the ethanol yield rate of L. japonica acid hydrolysate was the highest, which reached 0.17 g/g ethanol to L. japonica. It showed that strain A can converse alginate to ethanol in a relatively high yield rate, and might be a promising strain with L. japonica as the substrate, we believe more research should be carried out on this strain.     

Effect of ultrasonication treatment and fermentation by probiotic Lactobacillus plantarum strains on goat milk bioactivities

In the present research, the effects of continuous ultrasound treatment (100 W, 30 kHz; 0%, 30%, 60% and 90% amplitudes, 15 min) and fermentation process (37°C, 24 h) on the growth of Lactobacillus plantarum LP3 and LU5 strains and bioactive properties (peptide content, α-amylase and α-glucosidase inhibition, anticancer and antioxidant activities and exopolysaccharide content) of goat milk were investigated. According to our results, the ultrasonication of milk up to 60% amplitude promoted the growth of Lactobacillus strains and enhanced the bioactive properties compared with control during fermentation, while, the ultrasonication at 90% amplitude had negative effects on the mentioned parameters. Exopolysaccharide content, α-amylase inhibition, α-glucosidase inhibition, antioxidant activity and anticancer activity of treated samples at 60% amplitude at the end of fermentation in comparison to its beginning were increased 18.09, 12.79, 12.44, 9.4 and 1.92 folds, respectively. Also, the increase of assayed characteristics was found strain-dependent, so that L. plantarum LP3 was more effective than LU5 strain.