磨料有序排布电镀砂轮的制备及其把持力研究

为解决电镀砂轮磨削加工中容屑空间不足的问题，采用点胶微粘接的方法制备了磨料有序排布的电镀砂轮，分析了磨料粘接效果和镀层力学性能。通过SEM分析了磨料/镀层/导电胶的结合界面，并进行了干磨削试验。研究结果表明，直径约为磨料粒径40%的胶点可粘接住磨料，单个胶点上粘接多颗磨料的占比小于6%；双脉冲电镀工艺制备的镀层显微硬度大于500HV，表层残余应力小于100MPa，磨料/镀层/导电胶之间的界面贴合紧密，无明显缺陷；砂轮在磨削时没有出现磨料脱落现象。     

Investigation of the influence of iron-containing abrasives on the corrosion behaviour of the aluminium alloy AlSi1.2Mg0.4

The corrosion resistance of aluminium surfaces is closely linked to the surface state after a grinding process. For years, iron-containing abrasive materials were suspected to lead to increased corrosion susceptibility after processing of aluminium surfaces. To prove a possible correlation between the iron content of an abrasive and the corrosion behaviour of aluminium components, scientific investigations and experimentally practical corrosion tests are necessary. For the current investigation, specimens of a technical Al-Si alloy from the same batch were used. The test specimens were mechanically ground with various resin-bonded model abrasives containing different iron contents. The performed corrosion tests did not reveal a negative influence of the different iron-containing abrasives on the corrosion behaviour of the Al–Si alloy. However, the most sensitive measuring method (electrochemical noise) showed differences in the surface activity depending on the type of abrasive.     

微结构模芯的精密磨削及其在微注塑成形中应用

针对微结构聚合物元器件的批量化生产与制造效率低等问题，采用精密修整成V形尖端的金刚石砂轮，在自润滑性和脱模性良好的钛硅碳陶瓷模芯表面加工制造出形状精度可控的V沟槽阵列结构，然后利用微注塑成形工艺将模芯表面的V沟槽阵列结构一次成形复制到聚合物表面，高效注塑成形制造出倒V形阵列结构的聚合物工件。分析了微模芯的表面加工质量与形状精度，研究了熔体温度、注射速度、保压压力、保压时间等微注塑成形工艺参数对微结构聚合物注塑成形角度偏差和填充率的影响。实验结果表明：通过微细磨削加工技术和微注塑成形工艺可以高效率、高精度地制造出规则整齐的微结构注塑工件，注射速度对微成形角度偏差的影响最大，保压压力对微成形填充率的影响最大，微结构模芯的微细磨削形状精度值为4.05 μm，微成形的最小角度偏差和最大填充率分别为1.47°和99.30%。     

Ductile-brittle transition mechanisms of amorphous glass subjected to taper grinding experiment

Taper grinding experiments were conducted in this paper to investigate the continuous and complete ductile-brittle transition process of two kinds of amorphous glass: high purity fused silica (HPFS) which is silica rich glass and soda-lime silica glass (SLSG) which is low silica glass. The grinding force, ground surface morphology, surface roughness, and subsurface damage depth induced during different stages of taper grinding were all analyzed. A mathematical model describing the cutting force of a grit and micro-crack length was established to clarify the ductile-brittle transition mechanisms of isotropic material. The model revealed that material removal mechanisms and grinding force were mainly determined by the crack equivalent length in front of the grit and its equivalent cutting force. The ground surface roughness and subsurface damage depth were mainly affected by the cutting force of the grit and length of cracks behind it. The ductile machinability of SLSG was better than that of HPFS due to the bonding of metallic atoms in SLSG with nonbridging oxygens, as well as their packing into free volume in SiO₂ network.     

磁铁尾矿与石灰石双掺生产优质水泥

受环保压力影响，西乡公司生产水泥用河道淤沙供应紧张，难以满足生产需求且价格上涨幅度较大，严重影响到水泥生产及成本，我们开展了磁铁尾矿在水泥中的应用研究工作，通过连续几个月的生产实践，对物料配比优化，磨机技术改造，实现利用磁铁尾矿与石灰石双掺解决混合材紧缺问题，降低了水泥生产成本，水泥质量及性能稳定。     

精密磨床转台静压轴承的强健化设计

针对精密磨床转台静压轴承性能仿真数据与其回转精度实测数据不一致的问题，为提高转台静压轴承的设计水平，提出了静压轴承的强健化设计方法。该方法考虑了轴承结构参数在轴承全生命周期内的变化，分析了半径间隙、油腔尺寸、节流比及润滑油黏度在设计、加工、装配和服役4个阶段的变化规律，重点研究了半径间隙在各阶段对轴承性能造成的影响，给出了转台静压轴承的强健化设计流程。通过一个径向轴承的设计实例对该强健化设计方法进行了说明，并将设计结果与传统设计进行了对比。对比的指标是轴承在4个阶段的刚度、承载力和温升，这3个指标对轴承回转精度有直接影响。研究表明：进行强健化设计后，在生命周期内静压轴承的刚度和承载力的变化量为10%~27%，温度的变化量为0.5%~1.6%，较传统设计更能保证转台回转精度的稳定。     

Effect of wear behaviour of single mono- and poly-crystalline cBN grains on the grinding performance of Inconel 718

Polycrystalline cubic boron nitride (PcBN) grains were fabricated by combining the monocrystalline cBN (McBN) nanoparticles and inter-abrasive ceramic materials via high temperature and pressure techniques. Grinding performance of Inconel 718 with single McBN and PcBN grains, including grinding force, force ratio, ground surface quality was investigated. Characterization of the wear morphology evolution of worn grains and scratches of PcBN grains were discussed. In addition, the fracture behaviour of PcBN grains was evaluated as the varying of the undeformed chip thickness. Results show that PcBN grains have the smaller grinding force and force ratio, more stable grain wear rate in comparison to McBN grains. Additionally, the better wear-resistance and grinding performance owing to its multi-cutting edges structure in terms of the grain wear morphology evolution were achieved for PcBN grains regardless of the undeformed chip thickness.     

球磨过程中介质群运动区域划分方法研究

球磨过程中介质群运动状态变化对物料的破碎效率影响极大，通过对介质群运动状态进行区域划分，探究不同球磨工况下的介质群运动区域特征更能有效揭示介质群对物料的破碎方式和有效破碎区域。针对理论划分介质群运动区域过于理想、单一，试验追踪法成本过高的问题，提出了一种介质群运动区域划分的新方法-EDEM网格划分法。首先把筒体的横截面划分为若干个微元，利用数理统计的方法得到介质群位置概率分布函数，获取介质群运动速度区域分布图和碰撞特性区域分布图。然后给出了回转运动、螺旋运动及复合颤振运动三种工况下介质群运动区域的划分实例，并与试验追踪法对比，验证了EDEM网格划分法的准确性和有效性。最后通过粉磨试验中进料的破碎速率和微细颗粒产率探讨了介质群运动区域特性对颗粒的破碎方式和有效破碎区域的影响效果。本研究为优化球磨过程的影响因素和操作参数提供了一种快捷、有效的方法。     

郴州某复杂硫化铅锌矿阶段磨浮试验研究

针对郴州某复杂硫化铅锌矿资源的性质特点,采用铅快速浮选后尾矿再磨再选的阶磨阶选工艺,较好地实现了铅锌的高效浮选回收。研究了磨矿方式、捕收剂和调整剂种类及用量等因素对该矿石浮选的影响,确定了最佳浮选条件,通过小型闭路浮选试验,得到了铅品位60.05%、回收率89.63%的铅精矿和锌品位47.01%、回收率88.14%的锌精矿。