象山隧道液压凿岩台车开挖斜孔掏槽施工技术

新建的龙岩至厦门单线铁路象山隧道断面比较小,使用液压凿岩台车开挖,斜孔掏槽方案受到很大限制。本文介绍了使用液压凿岩台车钻爆开挖象山隧道,选择斜孔掏槽方案实现快速开挖,为类似的隧道工程施工提供经验。     

水压爆破拆除钢筋混凝土隐蔽部

水压爆破是一种控制爆破技术，它可在不动用机械设备情况下，用水作为介质，把炸药的爆炸能传递给待拆构筑物，达到破碎的目的。本文介绍采用水压爆破拆除钢筋混凝土工事的设计与实施，爆破取得圆满成功。     

Influence of bio-clogging on permeability characteristics of soil

It is necessary to enhance the barrier performance of cutoff walls in order to improve the contamination control level, especially for reconstruction or expansion of existing landfill sites. This paper presents a comprehensive laboratory investigation on the synergistic effects of microorganisms and fibers on the hydraulic conductivity of silty sand to evaluate the applicability to the field condition as an alterative barrier material. Inside the soil, the added carbon fibers not only provided good biocompatibility, but also formed spatial three-dimensional network between soil particles to improve the bacterial adhesion that eventually caused 2–3 orders of magnitude decrease in soil permeability. The resistance of the biofilm to extreme conditions was tested by permeation with solutions of different salinity and pH values, and by subjecting specimens to various hydraulic gradients and soil conditions. Despite the microbial growth inhibition occurred at these conditions, however, biofilm can largely remain intact and continue to reduce k, which due to the gradual adaptation of microorganisms to the extreme environment and the gradual recovery of their activity. Results of these tests demonstrate that biofilm treatment may be a feasible technology for creating waste containment barriers in soil.     

气瓶内部淬火过程的流动换热特性

 大直径厚壁气瓶内部淬火时的流动换热过程极其复杂，受到多种因素的影响，而研究气瓶内部压强和温度的变化规律对改善流动换热效果、提高产品组织性能具有重要的理论指导意义。以914 mm厚壁气瓶和瓶内流体为研究对象，建立了二维等效流 固耦合模型；采用多喷嘴系统对气瓶内外进行喷水淬火，研究了气瓶总长、喷水流速及淬火时间对瓶内压强及内壁温度的影响，通过间歇淬火试验验证了数学模型的正确性。结果发现，气瓶长度对瓶内压强和瓶壁温度的影响显著，喷水流速次之，当喷水流速大于8 m/s后，水量对瓶壁的冷却效果大大降低；气瓶内壁长度方向的温度梯度分别随气瓶总长的增加和淬火时间的延长而减小，但基本不受喷水量的影响。     

A new experimental simulation method for the development of non-renewable hydrogen energy—Oil and gas resources

At present, the proportion of tight oil in non-renewable hydrogen energy is increasing. According to an initial exploration and attemptable practice on the exploration of tight oil, it is found that the cost can be controlled effectively and positive effects are achieved. But this technique cannot make sure the proppants filled uniformly in the long fracture. Several researches on the proppants migration experiment devices and factors influencing on proppant setting are reviewed and a new set of experimental device to simulate the laws of proppants setting in long fracture is developed. This device can simulate the main factors influencing proppants setting performance. It analyzes several factors such as wall filtration, construction displacement, sand concentration, proppant size and density, viscosity of fracturing fluid is used to rank the influencing degree of every factor. Considering the effects of mutual interference between proppants, width of fracture, rough fracture surface and fracture surface filtration during the proppants setting progress, the mathematical model of proppant setting is modified by adding sand concentration correction factor, wall effect correction factor and filtration correction factor. The experimental data verify the accuracy of the settlement model is established using the data getting from experiment.     

浅谈液压夹具在转向油缸铸造缸盖加工上的应用

随着液压夹具在机械加工中运用推广,该公司引用液压夹具多年来取得一定成效,文章针对转向油缸的铸造缸盖铣、钻序前后加工工装进行对比分析,重点突出应用全自动液压夹具后可提升装夹效率、加工质量以及降低劳动强度等,可以在不添置设备的情况下,满足产能提升的需求。     

二级剪叉式液压升降机液压缸布置方式研究

分析了二级剪叉式液压升降机的三种主要布置方式,以及液压缸倾斜布置时的三种液压缸安装位置方案。对于其中的一种方案,应用虚位移原理计算求解液压缸推力,并以液压缸推力最小为目标建立优化设计数学模型,通过MATLAB软件得到液压缸推力最小时的液压缸安装位置。通过研究液压缸布置方式,提高了二级剪叉式液压升降机的设计效率和传动质量。     

基于ABAQUS的发动机缸盖工装强度分析

分析计算某型号发动机缸盖及工装的应力与局部位移,基于HyperMesh软件建立缸盖及工装的仿真模型,使用ABAQUS软件进行静力学计算,对处于夹紧状态下的发动机缸盖进行4个典型工位的加工工况分析计算,得出工件加工位置最大位移与工装所受最大应力。通过强度和位移校核,最终结果满足缸盖的加工需求,为工艺制定提供了有效的数据支持。