杂化包覆玄武岩鳞片/环氧涂料制备与性能

本文在环氧涂料中添加玄武岩鳞片，提高其防腐蚀性能。针对玄武岩鳞片的团聚问题，通过机械力化学改性工艺，采用正硅酸四乙酯、HY-311型钛酸酯偶联剂、E-44型环氧树脂对玄武岩鳞片进行杂化包覆，结果表明，杂化包覆后玄武岩鳞片的沉降时间从2h提高至96 h。杂化包覆玄武岩鳞片添加量为20%涂层的性能最优，附着力为13.40 MPa，耐盐雾时间为2000 h，在3.5%NaCl溶液中浸泡2000 h后，0.01 Hz的阻抗模值仍然有5.15×109 Ω·cm2。     

A Ti3C2Tx-carbon black-acrylic epoxy coating for 304SS bipolar plates with enhanced corrosion resistant and conductivity

A conducting and anticorrosive coating is crucial for the application of metal bipolar plates (BP) in proton exchange membrane fuel cell (PEMFC). In this work, a Ti₃C₂T_x (T)-carbon black (C)-acrylic epoxy (AE) coating is prepared on 304 stainless steel (SS) with enhanced corrosion resistance and conductivity. The corrosion resistance of the T-C-AE coating is investigated in a 0.5 M H₂SO₄ solution as compared to the AE, T, and T-AE coatings. The T-C-AE coated 304SS exhibits the strongest corrosion resistance with the most positive corrosion potential and the lowest corrosion current density of 0.00673 μA cm^?2 in all the samples, while retaining intact and compact surface morphology with the lowest metal ion dissolution even after immersed for 720 h. The addition of Ti₃C₂T_x and carbon black into the AE matrix greatly decreases interfacial contact resistance (ICR), and the T-C-AE coating achieves a low ICR of 15.5 mΩ cm^?2 under 140 N cm^?2 compaction force. The excellent anticorrosion performance is mainly attributed to the physical barrier and the cathodic protection provided by the stacked Ti₃C₂T_x (MXene) nanosheets in the T-C-AE coating. This eco-friendly, conducting, and anticorrosive T-C-AE coating has a good application prospect on SS BP of PEMFC.     

Thermo-adjusted self-healing epoxy resins based on Diels–Alder dynamic chemical reaction

Micro-damage in materials could be repaired by endowing materials with self-healing performance. Herein, an epoxy resin with excellent self-healing performance grounded on thermo-reversible Diels–Alder dynamic chemical reaction was developed. Results showed that the bending strength and adhesive behavior of epoxy resin were influenced dramatically upon treatment with various temperatures. More importantly, damages created in epoxy resin could be repaired completely after suitable heat treatments. What is more, the healed epoxy resin exhibited much higher bending strength and adhesive performance than the pristine one did. The materials could be damaged and then repaired repeatedly. Meanwhile, the as-prepared self-healing epoxy resin exhibited excellent thermal reversibility and controllable adhesion. The thermo-adjusted self-healing performance endowed epoxy resin with recyclable and reusable performance. Therefore, the research made it possible of recycling waste epoxy resins.     

汽车同步器齿环用耐高温结构胶膜的性能研究

同步器齿环与碳纤维耐摩擦材料是通过胶粘剂实现粘接,而胶粘剂耐高温性能的优劣则是决定其使用寿命的决定性因素。本文研究了环氧树脂E-51体系、环氧树脂AG80体系以及基材表面处理工艺对于结构胶膜耐高温性能的影响,采用熔融共混法制备了胶粘剂并以玻璃纤维布为背衬制备了耐高温结构胶膜。采用高低温拉力机对不同体系制备的结构胶膜进行了常温、200℃高温的钢材搭接剪切强度的测试。结果表明,对于E-51体系,提高体系交联密度可显著增大常温剪切强度,但高温剪切强度明显下降;对于四官能度的AG80体系,AG80的用量是影响其高温性能的主要因素,同时基材表面喷砂水洗处理后可显著增大结构胶膜与基材粘接有效面积,进而显著改善高温性能。所制备的结构胶膜较常用胶粘剂使用更加便捷,耐高温性能优良,满足同步器齿环使用要求。     

Morphology,thermal and mechanical performance of epoxy/polysulfone composites improved by curing with two different aromatic diamines

Epoxy/polysufone (PSF) composites cured with 4,4'-diaminodiphenyl sulfone (DDS) and 4,4'-diaminodiphenyl methane (DDM) were fabricated, and the effect of dual curing reaction of diamines with epoxy on morphology, mechanical, and thermal performance was investigated. DSC results indicated that DDM was more reactive than DDS and the activation energy decreased with the rising of DDM content. Structures with small domain size at the early stage of phase separation were fixed by the fast epoxy-DDM reaction. When the DDM content was elevated to a high level, large dual structures were changed to fine bicontinuous structures, which was favorable to improve the mechanical property. The mechanical performance of epoxy composites was enhanced and the maximum values were achieved when the DDM/DDS ratio was located at 75/25 (PSF/DDS0.25-DDM0.75). The flexural and tensile strength relative to epoxy/DDM system were enhanced more than those relative to epoxy/DDS, while the increase in toughness was the opposite. TGA measurement showed that thermal stability of epoxy/PSF composites was improved because of the restricting effect of continuous PSF domains on thermal motion of epoxy. DMA analysis exhibited two relaxation peaks for PSF/DDS0.25-DDM0.75, which could be attributed to the formation of phase separated morphology and epoxy network with different cross-link density.     

聚苯乙烯/交联丙烯酸甲酯共混物的制备及其发泡性能研究

将聚苯乙烯（PS）颗粒溶解到二乙烯基苯（DVB）、丙烯酸甲酯（MA）与偶氮二异丁腈（AIBN）的混合物中，通过加热引发MA聚合，获得PS/交联PMA共混物, 采用釜压法制备了PS/交联PMA共混物泡沫。采用全自动视频光学接触角测试仪、差示扫描量热仪、傅里叶变换红外光谱仪、动态力学分析仪对PS/交联PMA共混物的结构和性能进行了表征，并通过扫描电子显微镜对PS/交联PMA共混物泡沫的结构进行了表征。结果表明，交联PMA的引入能提高体系的成核效率，随着MA用量的增加，PS/交联PMA共混物的接触角从PS的100.5 °降至86.1 °；当MA的用量为9.6份（质量份，下同）时，PS/交联PMA共混物的泡孔尺寸主要分布在40~60 μm之间，泡孔尺寸分布明显变窄，泡孔密度达到了1.2×10⁸ 个/cm³。     

Flame Retardancy and Mechanical Properties of Bio‐Based Furan Epoxy Resins with High Crosslink Density

This work outlines an interesting approach to bioepoxy resins from sustainable 2,5‐bis((oxiran‐2‐ylmethoxy)methyl)furan (BOF). The 3,3′‐diamino diphenyl‐sulfone (33DDS) and 4,4′‐diamino diphenyl‐sulfone (44DDS) are employed as hardeners. For comparison, petro‐based networks from diglycidyl ether of bisphenol A (DGEBA) are developed as well. The systematic analyses suggest that the BOF/DDS networks show higher crosslink densities and mechanical properties than DGEBA/DDS thermosets. Remarkably, an attractive multilayer tubular microstructure is fabricated in the BOF/44DDS thermosets, and it greatly enhances the mechanical performance. Apart from that, BOF/DDS composites exhibit excellent flame retardancy. Especially, for BOF/44DDS, the self‐extinguishment happens in 7 s. The fire retardant mechanism confirms that a low heat release rate and heat release capacity as well as a compact char layer occur in the pyrolysis of BOF/DDS. Thus, the BOF/DDS exhibits superior performance over its DGEBA counterparts and meets a wide variety of requirements in engineering.     

轨腰仿生自分层防腐梯度涂料合成及影响因素和结构探究

目的仿荷藕结构及功能,制备一种自分层防腐涂料。方法合成聚氨酯改性环氧树脂(PU/EP)及氟硅改性丙烯酸树脂(氟硅改性PAA),将两种树脂共混形成自分层涂料。通过铅笔硬度测试、机械性能测试、接触角测试、耐老化测试、划格法附着力测试、电化学阻抗测试等,分别评价两种树脂比例、混合溶剂比例对涂膜自分层行为及性能的影响,并通过SEM-EDS、红外光谱等表征技术分析涂膜分层后的结构。结果当PU/EP∶氟硅改性PAA=1∶1时,接触角达到96.0°,柔韧性为0.5 mm,耐冲击为50 cm,附着力等级为1,失光率降至19%;乙酸丁酯(NBAC)∶正丁醇(NBA)=4∶6时,涂膜分层情况良好,接触角达到107.7°,浸泡水中48 h耐水性无变化,失光率降至17%。SEM-EDS、红外光谱分析表明,自分层涂膜上层为氟硅改性PAA、底层为PU/EP,中间存在过渡涂层,过渡层两种树脂中的─COOH、─OH、环氧基发生反应,使整个涂层更具稳定性。经由EIS分析,在3.5%NaCl溶液中浸泡40天后,腐蚀介质没有渗透涂膜到达基底金属界面。结论制备的轨腰仿生自分层涂膜的机械性能、附着力、疏水性、耐老化、防腐蚀性能优异,涂膜结构稳定。     

The role of the ratio (PEG:PPG) of a triblock copolymer (PPG‐b‐PEG‐b‐PPG) in the cure kinetics,miscibility and thermal and mechanical properties in an epoxy matrix

The aim of this study was to evaluate the role of different poly(ethylene glycol):poly(propylene glycol) (PEG:PPG) molar ratios in a triblock copolymer in the cure kinetics, miscibility and thermal and mechanical properties in an epoxy matrix. The poly(propylene glycol)‐block‐poly(ethylene glycol)‐block‐poly(propylene glycol) (PPG‐b‐PEG‐b‐PPG) triblock copolymers used had two different molecular masses: 3300 and 2000 g mol^?1. The mass concentration of PEG in the copolymer structure played a key role in the miscibility and cure kinetics of the blend as well as in the thermal–mechanical properties. Phase separation was observed only for blends formed with the 3300 g mol^?1 triblock copolymer at 20 wt%. Concerning thermal properties, the miscibility of the copolymer in the epoxy matrix reduced the T_g value by 13 °C, although a 62% increase in fracture toughness (K_IC) was observed. After the addition of PPG‐b‐PEG‐b‐PPG with 3300 g mol^?1 there was a reduction in the modulus of elasticity by 8% compared to the neat matrix; no significant changes were observed in T_g values for the immiscible system. The use of PPG‐b‐PEG‐b‐PPG with 2000 g mol^?1 reduced the modulus of elasticity by approximately 47% and increased toughness (K_IC) up to 43%. Finally, for the curing kinetics of all materials, the incorporation of the triblock copolymer PPG‐b‐PEG‐b‐PPG delayed the cure reaction of the DGEBA/DDM (DGEBA, diglycidyl ether of bisphenol A; DDM, Q3‐4,4′‐Diaminodiphenylmethane) system when there is miscibility and accelerated the cure reaction when it is immiscible. All experimental curing reactions could be fitted to the Kamal autocatalytic model presenting an excellent agreement with experimental data. This model was able to capture some interesting features of the addition of triblock copolymers in an epoxy resin. © 2018 Society of Chemical Industry