钢混结构大型厂房整体式爆破拆除

采用整体式控制爆破拆除方案对华电扬州电厂钢筋混凝土框-排架结构厂房进行了爆破拆除。爆破前,对汽机房、厂房外墙和楼梯进行了预处理。将厂房划分为3个爆区,采用非电多回路网格式爆破网路,依靠东侧锅炉房倒塌施加在西侧锅炉房上的倾覆力矩,有效地克服了西侧锅炉房向西倒的难题,可为同类工程提供一定的参考。     

Reduced‐scale test to assess the effect of fire barriers on the flaming combustion of cored composites: An upholstery‐material case study

Herein, we describe a reduced‐scale test (“Cube” test), measuring the fire performance of specimens including a fire barrier (FB) and a flammable core material, which acts as the main fuel load. The specimen is intended to reproduce a cross‐section of a composite product where heat/mass transfer occurs primarily in a direction perpendicular to the FB. The Cube test procedure and benefits are discussed in this work by adopting residential upholstery furniture as an exemplary study. One flexible polyurethane foam, one polypropylene cover fabric, and 10 commercially available FBs were selected. They were used to compare the fire performance of FBs, measured in terms of peak of heat release rate, in the ASTM E1474‐14 standard test and the newly developed Cube test. Edge effects severely affected the performance of FBs in the ASTM E1474‐14 standard test but not in the Cube test. Furthermore, appropriate test conditions were determined in the Cube test to measure the so‐called “wetting point,” that is, the time and value of heat release rate measured when flammable liquid products were first observed on the bottom of the specimen. The relevance of the “wetting point” in terms of full‐scale fire performance and failure mechanism of FBs is discussed.     

多晶硅表面金属催化化学腐蚀法制绒研究现状

在多晶硅太阳能电池的生产过程中, 金刚线切割技术(Diamond wire sawn, DWS)具有切割速度快、精度高、原材料损耗少等优点, 受到了广泛关注。金刚线切割多晶硅表面形成的损伤层较浅, 与传统的酸腐蚀制绒技术无法匹配, 金属催化化学腐蚀法应运而生。金属催化化学腐蚀法制绒具有操作简单、结构可控且易形成高深宽比的绒面等优点, 具有广阔的应用前景。本文总结了不同类型的金属催化剂在制绒过程中的腐蚀机理及其形成的绒面结构, 深入分析和讨论了具有代表性的银、铜的单一及复合催化腐蚀过程及绒面结构和电池片性能。最后对金刚线切割多晶硅片表面的金属催化化学腐蚀法存在的问题进行了分析, 并展望了未来的研究方向。     

Investigation on thermal conductivity and mechanical properties of Si3N4 ceramics via one-step sintering

High thermal conductivity Si₃N₄ ceramics were fabricated using a one-step method consisting of reaction-bonded Si₃N₄ (RBSN) and post-sintering. The influence of Si content on nitridation rate, β/(α+β) phase rate, thermal conductivity and mechanical properties was investigated in this work. It is of special interest to note that the thermal conductivity showed a tendency to increase first and then decrease with increasing Si content. This experimental result shows that the optimal thermal conductivity and fracture toughness were obtained to be 66 W (m K)^-1 and 12.0 MPa m^1/2, respectively. As a comparison, the nitridation rate and β/(α+β) phase rate in a static pressure nitriding system, i.e., 97% (MS10), 97% (MS15), 97% (MS20) and 8.3% (MS10), 8.3% (MS15), 8.9% (MS20), respectively, have obvious advantages over those in a flowing nitriding system, i.e., 91% (MS10), 91% (MS15), 93% (MS20) and 3.1% (MS10), 3.3% (MS15), 3.3% (MS20), respectively. Moreover, high lattice integrity of the β-Si₃N₄ phase was observed, which can effectively confine O atoms into the β-Si₃N₄ lattice using MgO as a sintering additive. This result indicates that one-step sintering can provide a new route to prepare Si₃N₄ ceramics with a good combination of thermal conductivity and mechanical properties.     

铌对取向硅钢冷轧组织织构的影响

采用光学显微镜(OM)、电子背散射衍射(EBSD)等研究了铌对取向硅钢冷轧过程中的组织与织构的影响。结果表明:含铌正火板和不含铌正火板经冷轧后都是条带状组织,但含铌冷轧板在宽度方向更窄。铌元素的存在对织构也具有优化作用,经过中间退火后,含铌冷轧板二次冷轧织构得到明显改善,相较于不含铌二次冷轧板拥有强度较低的旋转立方织构以及强度较高的{111}<112>织构,其取向密度最高可达12.460。     

High-temperature behavior of oxide dispersion strengthening CoNiCrAlY

To fabricate oxide dispersion strengthened bond coatings, commercial Co–30wt-%Ni–20Cr–8Al–0?4Y powder was milled with 2% additions of Al₂O₃, Y₂O₃ or Y₂O₃ + HfO₂. Low-pressure plasma sprayed, free-standing specimens were oxidised in air + 10%H2O at 1100 °C both isothermally (100 h) and in 500, 1?h cycles. Dry air cyclic testing conducted at both ORNL and FZJ showed remarkably similar results. In general, the water vapour addition caused more scale spallation. Two LPPS specimens without oxide additions were tested for comparison. The specimens with 2%Al₂O₃ addition exhibited the best behaviour as the powder already contained 0?4%Y. Additions of 2%Y₂O₃ and especially 1%Y₂O₃ + 1%HfO₂ resulted in over-doping as evidenced by high mass gains and the formation of Y- and Hf-rich pegs. Scanning transmission electron microscopy of the isothermal specimens showed no Hf and/or Y segregation to the alumina scale grain boundaries in the over-doped specimens.     

小尺度交通信号灯的检测与状态识别

交通信号灯识别包括检测和状态识别，在智能交通系统中发挥重要作用。基于YOLOv3算法提出了一种交通信号灯检测与状态识别模型。针对交通信号灯相较于交通场景中其他目标具有尺度小的特性进行了算法的设计：降低骨干网络的下采样倍率以增加小尺度目标的特征描述能力；通过增大特征图的尺度来改进多尺度特征融合；引入广义交并比作为检测任务的损失函数来改进目标边界框的回归效果。同时，根据交通信号灯本身的特性，使用颜色和形状约束的方法对信号灯进行状态识别和类别验证。最后在公开的Bosch交通信号灯数据集上和实际的城区道路进行了实验验证。实验结果表明，所提出的算法能够提升交通信号灯识别的精度和召回率，识别准确率可以达到90%左右。     

硅量子点荧光传感器快速检测鲜奶中的四环素

建立以硅量子点(silicon quantum dot,SiQDs)为荧光传感器快速检测四环素的新方法,以N-(β-氨乙基)-γ-氨丙基甲基二甲氧基硅烷为硅源,柠檬酸为还原剂,采用水热法合成SiQDs;通过透射电镜(transmission electron microscope,TEM)和光谱分析法研究其形貌结构和光学特性;利用四环素能有效地猝灭SiQDs荧光,构建荧光传感器用于四环素检测。结果显示,所制备的SiQDs呈球形、稳定性高,水溶性好。在优化的实验条件下,方法的线性范围为0.05~90μmol/L,检出限为18 nmol/L,用于生鲜牛奶样品测定,加标回收率为92.36%~104.07%。该方法简便、快速、灵敏,适于鲜奶中四环素的准确测定。     

多层圆片级堆叠THz硅微波导结构的制作

基于微电子机械系统(MEMS)工艺,提出一种多层圆片堆叠的THz硅微波导结构及其制作方法。为了验证该结构在制作THz无源器件中的优势,基于6层圆片堆叠的硅微波导结构,设计了一种中心频率365 GHz、带宽80 GHz的功率分配/合成结构,并对其进行了仿真。研究了制作该结构的工艺流程,攻克了工艺过程中的关键技术,包括硅深槽刻蚀技术和多层热压键合技术,并给出了工艺结果。最终实现了多层圆片堆叠功率分配/合成结构的工艺制作和测试。测试结果表明,尽管样品的插入损耗较仿真值增加3 dB左右,考虑到加工误差和夹具损耗等情况,样品主要技术指标与设计值较为一致。