Microstructure and electromagnetic properties of LiFe5O8 ferrite ceramics prepared from wet- and dry-milled powders

The effect of dry and wet ball milling of LiFe₅O₈ ferrite powder on the microstructure and electromagnetic properties of ferrite ceramics was studied using XRD analysis, scanning electron microscopy, dilatometry, thermogravimetry, calorimetry, and measurement of specific magnetization and electrical resistance. The sintering temperature was 1050 °C; the sintering time was 2 h. It was found that ferrite fabricated from dry-milled powder exhibits an ordered α-LiFe₅O₈ phase with bulk density of 91%. Its saturation magnetization and Curie temperature are 55 emu/g and 628°С, respectively. Specific electrical resistance is 4?10⁶ Ω cm. Wet milling in isopropyl alcohol causes formation of a disordered β-LiFe₅O₈ phase. Ceramics produced by this method shows higher bulk density (97%) and low porosity, and an order of magnitude lower resistivity. Its saturation magnetization and Curie temperature are 51 emu/g and 607°С, respectively.     

High dielectric constant of NiFe2O4–LaFeO3 nanocomposite: Interfacial conduction and dielectric loss

Materials exhibiting colossal dielectric constant are the most sought-after materials due to their variety of applications in various electronics industries. NiFe₂O₄ and LaFeO₃ belonging to the spinel and perovskite structures, respectively, were coupled into a nanocomposite by adapting a one-pot sol-gel synthesis. The ratio of NiFe₂O₄:LaFeO₃ was varied and the synthesized materials were studied for their dielectric behaviors. Interestingly, among the samples studied, the nanocomposite with the ratio of 1:2 of NiFe₂O₄–LaFeO₃ exhibited a high dielectric constant value of 10390 at a frequency of 1 kHz with a several-fold increase in conductivity. The high conductivity resulted in a high dielectric loss. The origin of such a high dielectric constant and loss have been attributed to the Maxwell-Wagner type space charge polarization arising from the microstructure that consists of large and continuous grain boundaries, and the conducting phase at the interface, respectively.     

Non-Platinum Group Metal Electrocatalysts toward Efficient Hydrogen Oxidation Reaction

Developing non-platinum group metal (non-PGM) electrocatalysts for the hydrogen oxidation reaction (HOR) represents the efforts towards the more economical use of hydrogen fuel cells and hydrogen energy, which has attracted tremendous attention recently. However, non-PGM electrocatalysts for the HOR are still in their early development stages as compared with the significant advances in those for the oxygen reduction reaction and hydrogen evolution reaction. Herein, this paper summarizes the recent progresses and highlights the key challenges for the rational design of non-PGM electrocatalysts, aiming to promote the development of non-PGM HOR electrocatalysts. Fundamental understandings of the HOR mechanism are firstly reviewed, where theoretical interpretations on the low HOR kinetics in alkaline media, including the hydrogen binding energy theory, the bifunctional mechanism, and the water molecule reorganization, are particularly discussed. Subsequently, progresses of typical non-PGM HOR electrocatalysts in acid and alkaline media are summarized separately. For the HOR under alkaline conditions, the superiorities and challenges of Ni-based catalysts are discussed with a particular focus as they are the most promising non-PGM electrocatalysts. Finally, this paper highlights the challenges and provide perspectives on the future development directions of non-PGM HOR electrocatalysts.     

Synthesis,Anticancer Activity,Structure-Activity Relationship and Mechanistic Investigations of Falcarindiol Analogues

Forty samples of optically active falcarindiol analogues are synthesized by using the easily available C2 symmetric (R)- and (S)-1,1’-binaphth-2-ol (BINOL) in combination with Ti(OⁱPr)₄, Zn powder and EtI. Their anticancer activities on Hccc-9810, HepG2, MDA-MB-231, Hela, MG-63 and H460 cells are assayed to elucidate their structure-activity relationships. These results showed that the falcarindiol analogue (3R,8S)- 2 i with the terminal double bond has the most potent anti-proliferation effect on Hccc-9810 cells with IC₅₀ value of 0.46 μM. The falcarindiol analogue (3R,8S)- 2 i can induce obvious Hccc-9810 cell apoptosis in a concentration-dependent manner by Hoechst staining and flow cytometry analysis. The proposed mechanism suggests that the falcarindiol analogue (3R,8S)- 2 i increases LDH release and MDA content, and reduces the levels of SOD activity, which lead to the accumulation of oxidative stress and induce apoptosis in Hccc-9810 cells.     

Preliminary Structural Data Revealed That the SARS-CoV-2 B.1.617 Variant's RBD Binds to ACE2 Receptor Stronger Than the Wild Type to Enhance the Infectivity

The evolution of new SARS-CoV-2 variants around the globe has made the COVID-19 pandemic more worrisome, further pressuring the health care system and immunity. Novel variations that are unique to the receptor-binding motif (RBM) of the receptor-binding domain (RBD) spike glycoprotein, i. e. L452R-E484Q, may play a different role in the B.1.617 (also known as G/452R.V3) variant's pathogenicity and better survival compared to the wild type. Therefore, a thorough analysis is needed to understand the impact of these mutations on binding with host receptor (RBD) and to guide new therapeutics development. In this study, we used structural and biomolecular simulation techniques to explore the impact of specific mutations (L452R-E484Q) in the B.1.617 variant on the binding of RBD to the host receptor ACE2. Our analysis revealed that the B.1.617 variant possesses different dynamic behaviours by altering dynamic-stability, residual flexibility and structural compactness. Moreover, the new variant had altered the bonding network and structural-dynamics properties significantly. MM/GBSA technique was used, which further established the binding differences between the wild type and B.1.617 variant. In conclusion, this study provides a strong impetus to develop novel drugs against the new SARS-CoV-2 variants.     

Integrating coral-like morphology into cyano-containing carbon nitride towards efficient photocatalytic H2 evolution and Cr(Ⅵ) reduction

The incomplete polymerization of graphite carbon nitride (g-C₃N₄) due to the kinetic problems resulted in its high recombination rate of photo-generated electron-hole pairs. Hence, cyano-containing carbon nitride with coral-like morphology (CCCN) was prepared by the molten salt method with heptazine-based melem as precursor, which presented excellent separation rate of photo-generated electron-hole pairs. SEM exhibited that CCCN owned coral-like morphology which exposed ample active sites and enhanced the capture ability of visible light while FT-IR and XPS demonstrated that cyano groups appearing in coral-like carbon nitride enhanced the separation rate of photo-induced charge carriers. The synergistic effect of coral-like morphology and cyano groups endowed CCCN-15% with superior performance of both the photocatalytic H₂ evolution (4207 μmol h^?1 g^?1) and Cr (Ⅵ) reduction (k = 0.059 min^?1), approximately 16.8 and 6.0 times that of g-C₃N₄, which was comparable among the similar materials. Density functional theory calculation (DFT) revealed that cyano groups decreased the bandgap and strengthened the activation degree of reaction substrate, which enhanced the thermodynamic driving force and the interaction between catalyst and substrate. This work provided a potential strategy for both the renewable energy generation and environmental restoration.     

Adaptive response and tolerance to weak acids in Saccharomyces cerevisiae boulardii: a metabolomics approach

Weak acids inhibit the growth of probiotics, such as Saccharomyces boulardii. We explored the tolerance of S. boulardii to different weak acids. S. boulardii had better fermentation ability under lactic acid conditions compared with acetic and butyric acid conditions; however, the budding of S. boulardii was significantly stronger than that of Saccharomyces cerevisiae under acetic acid conditions. Although the surface structure of S. boulardii was destroyed, it produced more daughter cells. S. boulardii metabolites were also significantly different from S. cerevisiae under acidic stress. The growth of S. boulardii under weak acid conditions differed significantly from that of S. cerevisiae. S. boulardii-mediated fingerprints under weak acid conditions were identified as latent biomarkers, related to fructose and mannose metabolism, tricarboxylic acid cycle, and the glycolysis pathway. Identified biomarkers will aid in the genetic engineering of S. boulardii and other Saccharomyces strains for improved acid resistance and biomass yield.     

南水北调中线总干渠藻类的生态调度

南水北调中线总干渠无在线调蓄水库,对藻类生态调度过程中出现的问题开展生态调度实现策略和实施方式研究。主要实现策略包括:划定自身的调蓄区,隔离生态调度对下游的影响;采用高效的渠池运行方式,减少生态调度时蓄量的反复调整;综合考虑安全、快速、平稳等需求,设定生态调度实施进程和方式。具体实施方式包括:将总干渠划分为流速调控区、调蓄区和正常运行区,分别实施等体积、控制蓄量和闸前常水位方式运行;将生态调度过程划分为充水阶段和泄水阶段,基于流速调控目标值、持续时长和水位降幅约束条件,确定各阶段时长和各分区的闸门群调控方案等。基于2018年3月输水工况,采用明渠一维非恒定流模型,仿真总干渠上游15个渠池的藻类生态调度过程。结果表明,生态调度可在3.5 d内完成,各渠池的平均流速由0.48 m/s增至0.93 m/s,持续时间超过2 h。在整个生态调度过程中,水位变化平稳,水位变幅符合安全阈值要求,下游渠道的正常运行未受生态调度明显影响。     

Application of artificial neural network method to predict the breakage properties of PGE bearing chromite ore

In the present investigation, systematic grinding experiments were conducted in a laboratory ball mill to determine the breakage properties of low-grade PGE bearing chromite ore. The population balance modeling technique was used to study the breakage parameters such as primary breakage distribution (B_{i, j}) and the specific rates of breakage (S_i). The breakage and selection function values were determined for six feed sizes. The results stated that the breakage follows the first-order grinding kinetics for all the feed sizes. It was observed that the coarser feed sizes exhibit higher selection function values than the finer feed size. Further, an artificial neural network was used to predict breakage characteristics of low-grade PGE bearing chromite ore. The predicted results obtained from the neural network modeling were close to the experimental results with a correlation of determination R² = 0.99 for both product size and selection function.     

Catalysts by pyrolysis: Direct observation of transformations during re-pyrolysis of transition metal-nitrogen-carbon materials leading to state-of-the-art platinum group metal-free electrocatalyst

Transition metal-nitrogen-carbon (M-N-C) materials have been the focus of scientists’ efforts to address the rising need for earth-abundant materials solutions for energy technology and decarbonization of the economy. They are viewed as one of the most promising candidates to replace platinum group metal (PGM) catalysts in the fuel cell and energy conversion fields, including the application of oxygen reduction reaction, carbon dioxide reduction reaction, and nitrogen reduction reaction. In the effort to improve M-N-C materials properties and achieve atomic dispersity of the transition metal in the carbonaceous matrix, a re-pyrolysis process has been proposed. This secondary heat treatment process of already obtained primary pyrolysis-derived M-N-C materials has been widely reported to substantially improve the electrochemical performance and operational stability of the catalysts. Here, we report a systematic investigation of this process used on samples of templated M-N-C catalysts to obtain state-of-the-art catalysts via in situ heating X-ray photoelectron spectroscopy (XPS), scanning transmission electron microscopy (STEM), energy-dispersive X-ray spectroscopy (EDS), electron energy loss spectroscopy (EELS), X-ray diffraction (XRD), and X-ray computed tomography (CT) characterization methods. It is found that the re-pyrolysis of M-N-C materials could result in the partial amorphization of the carbonaceous substrate. It causes the rearrangement and transformation of multitudinous N moieties, leading to optimization of their morphological display and association with atomically dispersed transition metal dopants. Ultimately, the re-pyrolysis results in an increase in uniformity of the active Fe-N_x sites distribution without the formation of nano-crystalline phases (metallic or carbide) and with overall preservation of the morphology of the carbonaceous framework achieved during the first formative pyrolysis step of the templated synthesis. These observations provide confirmation that empirically established re-pyrolysis is recommended to be used on all M-N-C materials despite the different synthesis routes to obtain a practical advanced catalytic material.