Microbial fuel cell (MFC)-based biosensor for combined heavy metals monitoring and associated bioelectrochemical process

To explore the feasibility and related mechanism of MFC biosensor for wastewater detection under the action of combined heavy metals. Cyclic voltammetry (CV) and scanning electrochemical impedance spectroscopy (EIS) were used to explore the related bioelectrochemical process. The response of the reactor to single/combined heavy metals, low/high heavy metal concentrations, and the differences in ohmic resistance (Rs) and charge transfer resistance (Rct) were investigated using Ni as the core heavy metal and the combined action of Cd, Cu and Zn. The results indicated that there was a linear relationship between the concentration and output voltage of the MFC biosensor under the action of combined heavy metals (R² = 0.8803–0.973). However, the internal resistance (Rint) of the MFC biosensor under the action of single heavy metal was far less than that of the combined heavy metal group, and the power density (19.849 W m^?3) was 4 times that of the combined heavy metal group (3.109–4.589 W m^?3). The Rs of the biosensors in the combined heavy metal group were 0.868Ω and 0.860, which were higher than 0.768Ω of the single heavy metal sensor. With the increase of the concentration of heavy metals in the influent, the increase of Rct was more obvious in the combined group, while the Rs in the single group significantly increased (P < 0.05). The results imply that it is possible for MFC biosensors to be used in the detection of actual water polluted by various heavy metals, but the biosensor performance is mainly limited by Rct, which needs to be further improved.     

Good dielectric performance and broadband dielectric polarization in Ag,Nb co-doped TiO2

Due to the demand of miniaturization and integration for ceramic capacitors in electronic components market, TiO₂-based ceramics with colossal permittivity has become a research hotspot in recent years. In this work, we report that Ag⁺/Nb⁵⁺ co-doped (Ag_1/4Nb_3/4)_xTi_1−xO₂ (ANTOx) ceramics with colossal permittivity over a wide frequency and temperature range were successfully prepared by a traditional solid–state method. Notably, compositions of ANTO0.005 and ANTO0.01 respectively exhibit both low dielectric loss (0.040 and 0.050 at 1 kHz), high dielectric permittivity (9.2 × 10³ and 1.6 × 10⁴ at 1 kHz), and good thermal stability, which satisfy the requirements for the temperature range of application of X9R and X8R ceramic capacitors, respectively. The origin of the dielectric behavior was attributed to five dielectric relaxation phenomena, i.e., localized carriers' hopping, electron–pinned defect–dipoles, interfacial polarization, and oxygen vacancies ionization and diffusion, as suggested by dielectric temperature spectra and valence state analysis via XPS; wherein, electron-pinned defect–dipoles and internal barrier layer capacitance are believed to be the main causes for the giant dielectric permittivity in ANTOx ceramics.     

无线电综合测试仪校准装置的研究及其不确定度分析

This calibration device of radio comprehensive tester is studied and established in this paper. It solves the verification and calibration of a large number of general-purpose radio comprehensive testers. The calibration device consists of four calibration sub- systems and calibration software system, including RF generator, audio generator, audio analyzer and RF analyzer. It also researches on the configuration of standard equipment and analyzes the uncertainty of the calibration devices, ensuring accurate and reliable val- ue transfer.     

Up-pulling force analysis for ESC hollow cylindrical casting

Electroslag casting(ESC)is an important method to produce high quality castings.In this study,the ESC up-pulling inner mold method(EUPIM)was used to produce hollow cylindrical castings with the multiple consumable electrodes.The radial deformation,the axial and radial internal stress of the inner mold,and the axial internal stress of the slag shell were analyzed using the finite element method(FEM)with the aid of ANSYS software.The ProCAST software was used to calculate the specific heat,heat conductivity and density curve of Cu.Simulation results show that the radial deformation,the axial and radial internal stress of the inner mold,and the axial internal stress of the slag shell near the slag-metal interface of hollow cylndrical casting gradually increase from 0 s to 360 s after the ESC starting(slagging)process but before applying the up-pulling force.The suitable initial up-pulling moment of the inner mold is at around 180-198 s after the starting process.     

微间隙共形圆柱接触力模型的适用性分析

针对目前间隙铰接副接触力模型无法有效表述不同材料耗散阻尼效应,以及不适用于微间隙共形接触的问题,分析各种接触力模型中弹性接触力和耗散阻尼力计算方法的优缺点,提出一种普适性的圆柱内接触力分析模型。该模型将接触力描述为接触深度的显式函数,并将其适用范围有效地扩展至微间隙和低恢复系数工况。采用含间隙铰接副的曲柄-滑块机构进行动力学分析,对所提出接触力进行验证,计算结果表明:所提出的普适性接触力模型体现了微间隙时更高的接触刚度和低恢复系数时显著的阻尼效应,从而可为不同材料和间隙尺寸的间隙铰接副力学分析提供更为完备的计算模型。     

基于英飞凌TC275的整车控制器CCP协议底层驱动开发

针对以英飞凌TC275单片机为平台的整车控制器,进行控制器局域网络标定协议(controller area network calibration protocol,CCP)底层驱动程序的开发。依据CCP的需求开发了英飞凌TC275的控制器局域网络(controller area network,CAN)模块、系统定时器(system timer,STM)模块和FLASH模块的底层驱动程序,实现CCP标定系统的通信连接、数据上传、数据下载、数据存储等功能。为验证系统的性能,进行整车控制器的实际测试,测试结果表明:所开发的基于TC275单片机的CCP底层驱动程序能够实现CCP的功能要求。     

Propagation and termination of an internal crack in continuously cast austenitic stainless steel analyzed by ∑ values and the Schmid factor

The formation mechanism of an internal crack was clarified from the viewpoint of the crystallography and thermal expansion. An inverse pole figure map obtained by EBSD pattern showed that the crack propagated along the grain boundaries having high ∑ values within the columnar zone. After the crack initiation, these positions were considered to undergo cracking followed by propagation toward the equiaxed side. Near the termination position, the grains ahead of crack propagation had a Schmid factor higher than 0.45 consuming elastic strain energy. Thermal expansion measurements showed that the grain with (0 0 1) orientation had the largest expansion while that with (0 1 1) the smallest. The grain boundaries neighboring the combination of (0 0 1) and (0 1 1) grains had the largest thermal stress. Therefore, thermal stress contributed to the initiation of cracking. It was thus proposed to enlarge the equiaxed zone to prevent cracking by discontinuing the crack propagation.     

双离心机法线加速度计动态校准中三参数余弦算法实现及应用

在双离心机的线加速度计动态校准中,三参数余弦算法贯穿在幅频特性、相频特性以及幅值线性度的整个测试中。本文详细描述了三参数余弦算法的概念和推导过程,以及在双离心机线加速度计动态校准数据处理过程中三参数余弦算法的程序实现;介绍了在幅频特性和相频特性中关于采集点的选取方式,降低由于采集点选择方式不同对数据拟合精度造成的影响。选取某型线加速度计为例,利用双离心机进行动态校准,对采集得到的数据点进行曲线拟合并得到测试结果,验证了所编写的三参数余弦算法程序的可行性。     

果蔬汁中氯氰菊酯、多效唑、哒螨灵含量测定能力验证结果分析

目的分析果蔬汁中氯氰菊酯、多效唑、哒螨灵含量测定能力验证结果。方法本实验室参加中国检验检疫科学研究院测试评价中心组织的果蔬汁中氯氰菊酯、多效唑、哒螨灵的测定能力验证(ACAS-PT806-2019),根据能力验证作业指导书要求和样品情况,采用了QuEChERS样品前处理净化方案,气相色谱电子捕获检测器检测氯氰菊酯,内标法定量,液相色谱串联质谱检测多效唑和哒螨灵,外标法定量。结果 1号样品中氯氰菊酯、多效唑、哒螨灵残留量分别为0.098、0.043、0.084 mg/kg, 2号样品中氯氰菊酯、多效唑、哒螨灵残留量分别为:0.036、未检出、0.013 mg/kg。所有测定项目结果均为满意(|Z|≤2)。结论实验室解决了此次能力验证中没有空白样品,检测项目基质效应差异明显等难点。实验室农药残留检测能力得到有效验证和提高。