低压静电场辅助冷冻对竹笋品质的影响

为研究低压静电场辅助冷冻对竹笋冻结特性的影响，以冻结曲线、硬度、水分损失率、水分迁移、冰晶形态和组织微观结构为指标，探究低压静电场辅助冷冻（－35 ℃）和普通冷冻（－35 ℃）条件下竹笋品质的变化规律。结果表明：低压静电场辅助冷冻提高了冻结效率，改变了冰晶形态及分布，减轻了组织微观结构破损程度，改善了解冻汁液流失情况。与静电板间距10、20、30、40 cm处的冷冻竹笋解冻后水分损失率分别为14.16%、12.58%、9.73%、10.44%，显著低于对照组（21.01%）（P＜0.05），硬度分别为461.19、507.48、496.65 g和455.31 g，显著高于对照组（350.70 g）（P＜0.05）。低场核磁共振分析结果表明，在低压静电场辅助冷冻下竹笋解冻后汁液流失减少，扫描电子显微镜观察结果显示，竹笋纤维排列整齐，组织微观结构保持较好。低压静电场辅助冷冻可有效改善竹笋品质，可为利用低压静电场进行果蔬的冷冻贮藏和冷链运输提供参考。     

Novel silicon-contained lignin-based carbon fibers derived from bamboo pulping black liquor with improved electrochemical performance for supercapacitors

Carbon fibers (CFs) are a promising candidate as electrode materials for flexible supercapacitors given its light weight and moderate cost. In this study, the lignin used was partially separated from kraft bamboo pulping black liquor and the higher molecular weight fraction, unavoidably contains a small amount of silicon compounds, so named silicon-contained lignin. Novel CFs were prepared using commercial polyacrylonitrile (PAN) and the lignin by electrospinning and further carbonization. Even in the presence of silicon compounds, the fibrous morphology of precursor fibers was significantly good, and the CFs with uniform fiber diameter and high specific surface area up to 182 m²/g were obtained with an increase in silicon-contained lignin. The CFs fabricated from silicon-contained lignin and commercial PAN had higher specific capacitance (22.20 mF/cm² at 10 mA/cm²) and superb cycling stability (94.21%) than that from silicon-free lignin or pure PAN separately.     

动态高压微射流处理对方竹笋膳食纤维理化及结构特性的影响

以方竹笋中提取的膳食纤维为研究对象，采用动态高压微射流（dynamic high-pressure micro-fluidization, DHPM）在不同压力条件（0，50，100，150，200 MPa）下进行处理，探究其对竹笋膳食纤维（bamboo shoots dietary fiber, BSDF）理化和结构特性的影响。结果表明，随着处理压力的增大，BSDF粒径先增大后减小，当处理压力为150 MPa时，粒径最小，为（370±11） nm，此条件下BSDF的持水力、持油力和膨胀力达到最大，较对照组分别提高了47.74%，50.54%，61.27%，且差异显著（P<0.05）。红外光谱分析表明DHPM处理不会改变BSDF的官能团，但会使BSDF内部的部分氢键断裂和半纤维素、木质素等发生降解；X射线衍射和热重分析表明DHPM处理不会引起BSDF的晶体结构改变，但晶体有序度会下降，进而导致其热稳定性降低；微观结构分析显示DHPM处理会使BSDF颗粒尺寸减小、表面粗糙、组织松散，且当处理压力为200 MPa时，颗粒发生团聚。综上，DHPM可以有效改善BSDF的理化性质，在膳食纤维改性方面具有一定的应用价值。     

竹材液化墙体泡沫材料的阻燃改性

为提高竹材液化产物所制备的高轻发泡墙体材料的防火性能，分别采用材料内部添加和表面浸泡的方法进行阻燃改性，并评价不同阻燃剂及其添加量对发泡材料阻燃性能的影响。实验结果表明：在材料内部或表面添加选择的阻燃剂不会对材料自身形貌或组分产生明显影响，对材料的力学性能亦不会造成破坏，在材料内部添加3 g膨胀型凝胶-二氧化硅/聚磷酸铵核壳阻燃剂（MCAPP）后压缩强度达到了0.37 MPa，在材料表面浸泡聚硅氧烷后压缩强度达到了0.58 MPa，同时能提高材料的阻燃性能，在材料内部添加聚磷酸铵（M-APP）后极限氧指数提高到33.2%，比改性前提高3%。在材料表面浸泡膨胀型壳聚糖-蒙脱土-聚磷酸铵（CMAp）后点燃时间明显延长，极限氧指数最高达到了31.5%。     

两台竹浆碱回收锅炉NOx、SO2排放的探讨

根据两台竹浆碱回收锅炉的实际运行情况,对其结构与运行对污染物排放的影响进行了比较、分析。     

Bamboo biochar-catalytic degradation of lignin under microwave heating

Abstract

Lignin biochar-catalytic depolymerization using biochar Fe-600, Fe-800, Ni-600, Ni-800 catalysts under microwave-heating (180?°C for 30?min) was explored in an ethanol/formic acid (1:1) media. Non-catalyst depolymerization was also studied and compared with the biochar-catalysts results. Characteristics of the bio-char catalysts were analyze by BET, XRD, and FT-IR. GPC, FT-IR, and MALDI-TOF MS spectrometry were also used to characterize the depolymerization products. The experimental results showed that the S_BET, V_t, and V_mec and average pore diameter of the biochars are considerably dependent on the preparation temperature and type of cation (Ni²⁺ or Fe³⁺). The maximum yield of bio-oil product was obtained as 85?wt% with the addition of biochar Ni-600 and the total amount of oligomers or monomers with a molecular weight of 164 to 446 reaches 80.4%.     

Prediction of the colorimetric parameters and mass loss of heat‐treated bamboo: Comparison of multiple linear regression and artificial neural network method

In this study, the colorimetric parameters (L*, a*, b*) and mass loss of heat‐treated bamboo were investigated, and the obtained results were modeled by using two methods: multiple linear regression (MLR) and artificial neural network (ANN). First, bamboo samples were exposed to heat treatment at different temperatures (110°C, 140°C, 170°C, and 200°C) and durations (15, 30, 45, 60, 75, 90, and 115 minutes) in a laboratory oven. Then, the colorimetric parameters (L*, a*, b*) and mass loss of each sample were measured after each period of heat treatment. All data were modeled by using two methods separately for each parameter and the performances of these proposed methods were compared. It was found that color change and mass loss increased with increasing temperature and duration of heat treatment. Mean absolute percentage error (MAPE) values of all obtained MLR ranged from 0.64% to 10.63%, while the all MAPE values of ANN were found to be lower than 1.5%. Based on these results, it can be said that MLR and ANN could be used to evaluate the changes on the selected properties of heat‐treated bamboo samples. On the other hand, it should be emphasized that the ANN gave more accurate results than the MLR method because of its learning capability.     

竹粉增强木质素-环氧树脂复合材料的力学性能

采用热压成型工艺制备了竹粉增强的木质素-环氧树脂复合材料,探讨了竹粉的添加量及其粒径对复合材料力学性能及热机械性能(DMA)的影响。研究结果表明,随着竹粉含量的增加,复合材料的弯曲强度与冲击强度均增大;粒径适中(40~80目)的竹粉增强的木质素-环氧树脂复合材料的弯曲强度和冲击强度最佳。随着竹粉含量的增加,复合材料的初始储能模量逐渐增大,玻璃化转变温度先升高而后降低;粒径适中(40~80目)的竹粉的添加对材料初始储能模量的提升有利。适当提高木质素-环氧树脂复合材料的交联密度,可以得到更好的力学性能。     

竹增强环氧乙烯基树脂的制备及性能研究

和传统的钢护拦相比较,竹片增强复合材料护拦具有重量轻、成本低、耐腐蚀、环境友善和可再生性等优点。但是竹纤维表面的复杂成分,影响了复合材料的界面性能。本文利用竹片作为增强材料,采用真空辅助成型方法制备了竹片增强环氧乙烯基树脂复合材料,研究了表面改性和铺层数对竹复合材料弯曲强度和冲击韧性的影响,并对单向复合材料的冲击断面破坏方式进行了分析。结果表明,在不同铺层结构条件下,用经过碱与硅烷偶联剂改性处理过的竹条制备的复合材料的弯曲强度分别提高了31.95%、46.72%、29.58%,冲击韧性分别提高了25.62%、29.74%、28.61%,而且单向复合材料的弯曲和冲击性能最佳。当单向复合材料中的竹片铺层为15层时,其冲击吸收功为13.55J,拉伸强度为270MPa,弯曲强度为340MPa,在主要性能上能满足公路防撞护栏对其原料Q-235B钢的要求;通过扫描电镜分析发现,竹片增强复合材料防撞护栏材料的防撞机理表现为竹纤维抽拔断裂、基体断裂、纤维/基体界面脱黏以及剪切分层。本文的结果对复合材料公路防撞护栏的制备有一定的指导作用。