高耸桥墩保护性爆破拆除关键技术

为解决高耸钢砼桥墩上部倾斜导致的工程质量不合格问题,采用保护性控制爆破将上部倾斜部分钢砼桥墩予以拆除,同时保留下部未偏斜部分桥墩不受破坏。采用开设组合形状切口,预开定向窗、导向窗;设置组合高差卸荷槽,预伤钢筋弱化抗压抗拉能力为关键措施的控制爆破方案。方案实施取得了十分满意的效果,上部拟拆除部分桥墩顺利倾倒下坠,下部保留部分桥墩完好无损。采用保护性控制爆破技术能高效、安全地解决类似高耸钢砼桥墩(构筑物)部分拆除、部分保留利用的问题,并能取得可观的经济、社会效益。     

箱形横梁的水压爆破拆除

某电影院大厅内钢筋混凝土箱形横梁长25m,断面尺寸1 6m×2 4m,用水压爆破拆除。通过梁的受力分析得知,为避免横梁的挠度过大,在吊梁拆除后必须另补支撑,以确保水压爆破正常进行。文中对水压爆破炸药用量的计算公式进行了比较和简评。在参考计算结果和考虑厅内环境的基础上,并结合以往水压爆破工程的经验,确定了合理、有效的药量,保证了主体结构的绝对安全。     

Current Status of Angiogenic Cell Therapy and Related Strategies Applied in Critical Limb Ischemia

Critical limb ischemia (CLI) constitutes the most severe form of peripheral arterial disease (PAD), it is characterized by progressive blockade of arterial vessels, commonly correlated to atherosclerosis. Currently, revascularization strategies (bypass grafting, angioplasty) remain the first option for CLI patients, although less than 45% of them are eligible for surgical intervention mainly due to associated comorbidities. Moreover, patients usually require amputation in the short-term. Angiogenic cell therapy has arisen as a promising alternative for these “no-option” patients, with many studies demonstrating the potential of stem cells to enhance revascularization by promoting vessel formation and blood flow recovery in ischemic tissues. Herein, we provide an overview of studies focused on the use of angiogenic cell therapies in CLI in the last years, from approaches testing different cell types in animal/pre-clinical models of CLI, to the clinical trials currently under evaluation. Furthermore, recent alternatives related to stem cell therapies such as the use of secretomes, exosomes, or even microRNA, will be also described.     

Effect of height on the corrosion of steel and galvanized steel in nontropical coastal marine environments

In this study, the behavior of carbon steel and galvanized steel in nontropical coastal marine environments was evaluated. Evaluation was carried out with specimens with dimensions of 10 cm × 10 cm × 0.3 cm. These specimens were exposed to four testing stations (Iquique, Mejillones, Los Vilos, and San Vicente), where racks were installed both at ground level (ground), as well as in the upper zone of electrical transmission towers (tower). In each station, 24 specimens of A36 carbon steel and galvanized steel were placed (12 each). The corrosivity of the environment was measured using the ISO 9223, 9225, and 9226 standards. The specimens were evaluated on-site, monthly, through visual inspection and photographic record. Once withdrawn, the corrosion rate was determined and the corrosion products were analyzed through Raman and Fourier-transform infrared. The results show that, in all cases, the corrosion rate is greater in the tower than on the ground. However, even though the Los Vilos station is located farther from the sea (3,500 vs. ≈500 m), the corrosion rate of steel in the tower is the highest. This is caused by the generation of HCl from the transformation of lepidocrocite into goethite, in the presence of low chloride content, which acidifies the steel/corrosion product interface. In the case of galvanized steel, the corrosion rate is a function of the chloride content in the atmosphere, obtaining an excellent correlation between both parameters.     

大采高综放工作面强动压端头顶板控制技术

为了解决大采高综放工作面回风侧端头顶板控制问题,针对马道头矿8211工作面的地质情况,通过对回风顺槽超前注浆加固,提高超前支护范围和支护强度,并对回风侧端头三角区煤壁和顶板进行化学浆加固的技术方案,有效控制了顺槽超前区围岩变形和工作面回风侧端头三角区煤壁片帮,保证了工作面端头区顶板安全。     

Nb和时效时间对热轧中锰TRIP钢中P偏聚的影响

热轧态中锰TRIP钢首先经650 ℃退火2 h,随后在550 ℃进行等温时效热处理,采用场发射扫描电镜(FE-SEM)研究该钢中P的偏聚和时效析出行为的变化情况。结果表明,中锰TRIP钢中P在晶界的偏聚是一种非平衡偏聚现象,临界时间约为50 h,与理论计算结果48 h较为吻合。在局部偏聚区域内,C与P存在共偏聚的关系,即P偏聚量高的地方,C含量也高。而合金元素Nb具有抑制P偏聚的效果,在20~70 h时效时间内,可以相对降低6.57%~19.5%的最大P偏聚量。根据电子背散射衍射(EBSD)菊池线分析,P偏聚量低于2.28at%时,P为固溶状态,高于2.28at.%时,P为析出状态。     

夹杂物对工程机械用钢Q345FCA疲劳寿命的影响

采用QBWP-6000J型简支梁旋转弯曲疲劳试验机测定了高疲劳寿命工程机械用钢Q345FCA的疲劳寿命;采用扫描电镜(SEM)对疲劳断口形貌进行了观察,并用附带的能谱仪(EDS)寻找断口上的夹杂物;借助夹杂物自动分析系统对钢中的夹杂物进行了分析。通过对试验数据的分析,计算得出了Q345FCA钢和Q345钢夹杂物的表面临界尺寸、次表面临界尺寸和内部临界尺寸。结果表明,Q345FCA钢的疲劳极限为273 MPa,Q345钢的疲劳极限为266 MPa。Q345FCA钢和Q345钢中夹杂物尺寸均小于临界夹杂物尺寸,且断口形貌显示所有疲劳断裂均不是由夹杂物所引起,夹杂物不是疲劳源。     

New insight to the oxidation kinetics of silicon-containing steel at high temperature

This study investigated the oxidation kinetics of silicon-containing steel at 1150–1300 °C using a Simultaneous Thermal Analyzer under atmospheric conditions similar to that of an industry reheating furnace. There is a critical time point for the oxidation kinetics at an oxygen concentration of 4·0 vol.-%., following which the oxidation rate constant increases with the increasing oxidation temperature. The model coefficient A in the kinetic oxidation equation was found to be constant. However, before the critical time point, the oxidation rate constant remained unchanged; the model coefficient A decreased with the increasing temperature. Therefore, the kinetic model of silicon-containing steel for isothermal oxidation was observed to be a modified one on the basis of the experimental data. In addition, the critical time point was prolonged with the increasing isothermal oxidation temperature. Moreover, the oxidation activation energy of the tested silicon-containing steel was 366·16 kJ mol^?1.     

Propagation of surface cracks on beam blank in the mould during continuous casting

ABSTRACT

We focus on crack propagation to investigate surface cracks in the mould during continuous casting, based on the crack initiation mechanism proposed in previous studies. The temperature and stress data of a solidified shell were extracted, and an extended finite element model based on the continuous damage theory of elastic–plastic materials was developed to simulate surface crack propagation. The results showed that, in the cracked area, stress concentration occurred at the crack tip, and the element split open and the crack propagated when the maximum principal stress in the stress concentration area reached the critical value. Prefabricated cracks in the fillet and web mainly developed into longitudinal cracks in the mould. The theoretical mechanism of this study was found to be the same as the crack propagation mechanism observed during the actual production of beam blanks. Thus, this study reveals the theoretical principle of crack initiation and propagation and can provide theoretical guidance for controlling surface cracks during beam blank continuous casting.