Effect of phosphogypsum on saline-alkalinity and aggregate stability of bauxite residue

A column experiment was conducted to investigate the effect of phosphogypsum (PG) on the saline- alkalinity, and aggregate stability of bauxite residue. Results showed that: with increasing leaching time, the concentrations of saline-alkali ions decreased while the concentration increased in bauxite residue leachate; compared with CK (control group) treatment, pH, electric conductivity (EC), exchangeable sodium percentage (ESP), sodium absorption ratio (SAR), and exchangeable Na⁺ content of bauxite residue were reduced following PG treatment; average particle sizes in aggregates following CK and PG treatments were determined to be 155 and 193 nm, respectively. SR-μCT test results also confirmed that bauxite residue following PG treatment acquired larger aggregates and larger pore diameter. These results indicate that the PG treatment could significantly modulate the saline-alkalinity, and simultaneously enhance aggregate stability of bauxite residue, which provides a facile approach to reclaim bauxite residue disposal areas.     

Superhydrophobic aluminum alloy surface with excellent universality,corrosion resistance,and antifouling performance prepared without prepolishing

It is urgently necessary to seek more simple and effective methods to construct superhydrophobic metal surfaces to improve the corrosion resistance and antifouling performance. Herein, a facile method for fabricating superhydrophobic aluminum alloy surface is developed via boiling water treatment and stearic acid modification. It is noteworthy that no prepolishing on aluminum alloy is required and no caustic reagents and typical equipments are used during the preparation procedure. Therefore, the fabrication method is quite a simple and environment-friendly technique. Both micro- and nano-scaled binary structure forms at the resultant aluminum alloy surface while long alkyl chains are grafted onto the rough aluminum alloy surface chemically. Consequently, the resultant aluminum alloy exhibits outstanding superhydrophobicity. More importantly, the superhydrophobicity has excellent universality, diversity, stability, excellent corrosion resistance, and antifouling performance. The facile preparation, excellent superhydrophobic durability, and outstanding performance are quite in favor of the practical application.     

Agronomic performance of high oleic,low linolenic soybean in Tennessee

Soybean oil hydrogenation alters the linolenic acid molecule to prevent the oil from becoming rancid, however, health reports have indicated trans-fat caused by hydrogenation, is not generally regarded as safe. Typical soybeans contain approximately 80 g kg⁻¹ to 120 g kg⁻¹ linolenic acid and 240 g kg⁻¹ of oleic acid. In an effort to accommodate the need for high-quality oil, the United Soybean Board introduced an industry standard for a high oleic acid greater than 750 g kg⁻¹ and linolenic acid less than 30 g kg⁻¹ oil. By combing mutations in the soybean plant at four loci, FAD2-1A and FAD2-1B, oleate desaturase genes and FAD3A and FAD3C, linoleate desaturase genes, and seed oil will not require hydrogenation to prevent oxidation and produce high-quality oil. In 2017 and 2018, a study comparing four near-isogenic lines across multiple Tennessee locations was performed to identify agronomic traits associated with mutations in FAD3A and FAD3C loci, while holding FAD2-1A and FAD2-1B constant in the mutant (high oleic) state. Soybean lines were assessed for yield and oil quality based on mutations at FAD2-1 and FAD3 loci. Variations of wild-type and mutant genotypes were compared at FAD3A and FAD3C loci. Analysis using a generalized linear mixed model in SAS 9.4, indicated no yield drag or other negative agronomic traits associated with the high oleic and low linolenic acid genotype. All four mutations of fad2-1A, fad2-1B, fad3A, and fad3C were determined as necessary to produce a soybean with the new industry standard (>750 g kg⁻¹ oleic and <30 g kg⁻¹ linolenic acid) in a maturity group-IV-Late cultivar for Tennessee growers.     

远志多糖对力竭运动小鼠体内抗疲劳和体外抗氧化作用研究

为了探讨远志多糖的体内、外活性，采用力竭运动动物模型，给予受试动物低、中、高剂量（0.10、0.20、0.40 mg/g·d）远志多糖后，分别测定各组动物负重游泳时间、肝糖原、肌糖原、乳酸、尿素氮含量及乳酸脱氢酶的活力和体外抗氧化活性。结果表明，与空白对照组相较，低、中、高剂量的远志多糖分别延长小鼠的负重游泳时间96.6 s （P<0.05）、254.4 s （P<0.01）和421.8 s （P<0.01），肝糖原含量分别提高13.1%（P<0.05）、37.4%（P<0.01）和56.4%（P<0.01），肌糖原含量分别提高10.8%（P<0.05）、31.2%（P<0.01）和42.0%（P<0.01），运动后乳酸含量分别下降4.6%（P<0.05）、8.6%（P<0.01）和14.5%（P<0.01），尿素氮含量分别降低1.5%（P<0.05）、3.9%（P<0.01）和7.5%（P<0.01），乳酸脱氢酶活力分别提高10.4%（P<0.01）、14.0%（P<0.01）和19.9%（P<0.01）。当远志多糖浓度为4 mg/mL时，对羟基自由基清除率和DPPH自由基的清除率分别为61.3%和79.5%，表明远志多糖有助于缓解机体疲劳，且体外抗氧化性较好。     

电磁脉冲辐射波模拟器双锥-平面线栅天线场分布规律

双锥-平面线栅结构的水平极化辐射波天线对辐射场半宽影响较小且架设方便、易于维护，掌握该型天线场分布规律是确定模拟器场均匀区、开展电磁脉冲效应实验的前提。利用天线理论研究双锥-平面线栅天线的场分布规律，结合数值模拟和实际天线试验对理论分析结果进行验证。结果表明：在天线结构和激励电压确定的条件下，双锥中心正下方辐射电场极化分量仅与测点到源的距离相关，二者呈反比；Oxz平面内以双锥中心为圆心的圆弧上任意一点辐射电场极化分量的幅值相等，并在同一时刻达到峰值；Oxz平面内同一水平线上的测点总辐射场幅值相等，方向沿测点所在圆弧的切线方向；各辐射场分量关于Oxz平面和Oyz平面对称分布；对于实际模拟器，地面反射会使辐射场波形下降沿陡降，导致地面附近辐射场半宽变小；线栅极板会影响附近的场分布，且极板外侧4个角点处的反射相对较强，其他位置辐射场分布与理论分析一致。     

Synthesis of magnetically recyclable porous CoFe2O4/Rh composites with large BET surface area for enhanced photocatalytic degradation of organic pollutant

The organic pollutants in water have been a great environment challenges to human beings, and photocatalytic degradation is an effective method to solve this problem. In this paper, the Rh-loaded cobalt ferrite CoFe₂O₄ (CFO) nanoparticles have been successfully synthesized by in situ photodeposition of Rh nanoparticles onto the porous CFO particles as the photocatalysts. After incorporating Rh nanoparticles, the CFO/Rh composite has a higher specific surface area and is more efficient in charge separation than the bare CFO. The photocatalytic efficiency of decomposing Malachite Green (MG) is improved from 70% over the bare CFO to 97% over the optimized CFO/Rh in 60 min. The CFO/Rh sample also demonstrates its durability for the degradation of MG in 5 photocatalytic reaction cycles. Additionally, hydroxyl radicals (?OH) and superoxide radicals (?O₂^?) are proved to be the crucial reactive species during the photocatalytic degradation of MG with CFO/Rh, evidenced by the active species capture experiments. This work provides a useful approach to enhance the photocatalytic activity of semiconductors for degrading organic dyes.     

氮含量及固溶温度对21-6-9奥氏体不锈钢组织和硬度的影响

为了探讨氮含量及固溶温度对21-6-9不锈钢组织和硬度的影响,分别在950、1000、1050和1100 ℃对3种不同氮含量的热轧态21-6-9不锈钢进行1 h固溶处理,通过光学显微镜观察其组织结构,结合Thermo-Calc热力学计算对试验钢的微观组织进行分析,并对其进行硬度测试。结果表明,0.20%~0.28%N的21-6-9不锈钢热轧后沿轧制方向析出铁素体,且钢中铁素体经950~1100 ℃固溶处理可消除,当N含量达到0.34%时,试验钢中不再出现铁素体。随着固溶处理温度的升高,21-6-9不锈钢的晶粒组织长大,硬度降低。N含量的增加可显著提高固溶态21-6-9不锈钢的硬度,其增加程度随固溶处理温度的升高而减弱。     

高铁桥梁智慧建造综合管控平台的设计与应用

为了提升高铁桥梁的施工技术和管理水平,通过地空快速高精度三维数据融合与场景构建技术,并结合建筑信息模型(Building Information Model,BIM)技术,开展基于工业互联网的工地数据库全连接研究,打破生产现场管理信息"孤岛",将拌合站、钢筋加工场、试验室、施工现场的三维场景、工艺生产、配料任务、施工进度、安全质量、视频监控、应力监测等数据进行关联,实现施工生产多维度数据全连接,最终构成基于"一张图"的企业级高铁桥梁施工智慧综合管控平台.     

Nacre-Inspired,Liquid Metal-Based Ultrasensitive Electronic Skin by Spatially Regulated Cracking Strategy

The realization of liquid metal-based wearable systems will be a milestone toward high-performance, integrated electronic skin. However, despite the revolutionary progress achieved in many other components of electronic skin, liquid metal-based flexible sensors still suffer from poor sensitivity due to the insufficient resistance change of liquid metal to deformation. Herein, a nacre-inspired architecture composed of a biphasic pattern (liquid metal with Cr/Cu underlayer) as “bricks” and strain-sensitive Ag film as “mortar” is developed, which breaks the long-standing sensitivity bottleneck of liquid metal-based electronic skin. With 2 orders of magnitude of sensitivity amplification while maintaining wide (>85%) working range, for the first time, liquid metal-based strain sensors rival the state-of-art counterparts. This liquid metal composite features spatially regulated cracking behavior. On the one hand, hard Cr cells locally modulate the strain distribution, which avoids premature cut-through cracks and prolongs the defect propagation in the adjacent Ag film. On the other hand, the separated liquid metal cells prevent unfavorable continuous liquid-metal paths and create crack-free regions during strain. Demonstrated in diverse scenarios, the proposed design concept may spark more applications of ultrasensitive liquid metal-based electronic skins, and reveals a pathway for sensor development via crack engineering.