移动边缘计算中资源分配和定价方法综述

移动边缘计算（mobile edge computing,MEC）通过将计算任务卸载至边缘服务器，降低网络负荷，减少传输时延，提升用户服务体验。因此，MEC受到了广泛关注，并成为5G的关键技术。资源分配作为MEC的主要问题，在提升能量效率、缩短任务时延和节约成本方面具有非常重大的研究意义。首先，介绍了MEC的基本概念、参考架构和技术优势；然后，从技术层面和经济层面归纳总结了MEC中最新的资源分配和定价策略；最后，讨论了MEC资源分配和定价策略中可能存在的问题与挑战，并提出了一些可行的解决方案，为后续研究发展提供参考。     

Gluten-free cakes with walnut flour: a technological,sensory, and microstructural approach

Walnut flour (WF), a by-product of walnut oil production, is characterised by high polyunsaturated fatty acids, proteins, and fibre contents and presents suitability for bakery products. However, when using non-traditional ingredients, it is essential to evaluate the effect on the quality properties of the final product. So, this work aimed to assess the impact of WF on the technological, physicochemical, and sensory properties of gluten-free (GF) cakes. WF was added at a flour blend (cassava (CS) and maize (MS) starches and rice flour) at 0, 10%, 15%, and 20%. The results showed that WF modified starch gelatinisation, increased amylose–lipid complex (ALC) content, and made crumbs easier to chew. Besides, the total dietary fibre (TDF) and protein content significantly increased. Cakes with 15% WF presented the highest specific volume (SV) and no differences in overall acceptability with respect to control. Hence, WF is a suitable ingredient for gluten-free bakery products.     

地表径流速度对城市内涝影响规律

为分析地表径流速度对城市内涝的影响,采用一维地下排水管网与二维城区地形的动态耦合模型,选取大连市某排水区块作为研究区域,设置4种地表径流速度10种设计降雨场景,模拟分析在不同重现期设计降雨及不同地表径流速度下研究区的内涝积水特性。结果表明:随着地表径流速度降低,管道排水压力变小,管道排水达标率最高可提升48.05%,且降雨重现期越短,地表径流流速对管道排水压力的削减效果越明显;地表径流流速对检查井溢流量影响显著,随着地表径流速度降低,检查井溢流量峰值最高可减小2 750 m~3,峰现时间最长可滞后56 min,同时随着降雨重现期增长,地表径流流速对检查井溢流量的削减效果减弱;研究区低、高风险区淹没面积随地表径流速度降低,最高可分别减小1.64万、8.37万m~2,但中风险区淹没面积变化反复。     

“方变圆”变径筒状结构滑模施工技术

为解决塔式光热的核心构筑物吸热塔"方变圆"变径超高筒体结构施工难题,选用一套可变形的滑模平台系统,通过操作系统上可调千斤顶支座、门架横向液压千斤顶装置、多处可调节模板角度和收缩模板的丝杆等,使得滑模根据施工需求可在一定的范围内调节模板倾角、间距,并逐步完成收缩变形,其理论滑模允许偏角20°,最终高效完成异形结构施工。该滑模系统刚度大、承载及堆料能力强、空间大、机械化程度高,施工操作简单,安全性高,适应沙漠极端环境。全过程仅需使用一套滑模体系,就能完成方形段、方变圆的变形段及圆形段施工,大大提高了施工效率,为类似环境下相似结构的施工提供了一定的参考。     

Centrifugally spun carbon fibers prepared from aqueous poly(vinylpyrrolidone) solutions as binder-free anodes in lithium-ion batteries

Aqueous solutions of poly(vinylpyrrolidone) (PVP) of various concentrations (20, 25, and 28 wt%) were successfully spun into fibers by centrifugal spinning. The pristine PVP fibers were annealed and carbonized to produce flexible carbon fibers for use as binder-free anodes in lithium-ion batteries. These flexible carbon fibers were prepared by developing a novel three-step heat treatment to reduce the residual stresses in the pristine PVP precursor fibers, and to prevent fiber degradation during carbonization. The thermogravimetric analysis data showed that the annealed fibers yielded a residual mass percentage of 36.0% while the pristine PVP fibers suffered a higher mass loss and only retained 26.5% of original mass above 450 °C (under nitrogen). The electrochemical performance of the carbon-fiber anodes was evaluated by conducting galvanostatic charge/discharge, rate performance, and cycle voltammetry experiments. The 20, 25, and 28 wt% derived binder-free anodes delivered specific charge capacities of 205, 189, and 275 mAh g⁻¹, respectively, after the first cycle at a current density of 100 mA g⁻¹. The results obtained in this work indicate that a feasible pathway towards a large-scale production of carbon-fiber anodes from a 100% aqueous solution can be achieved via centrifugal spinning and subsequent heat treatment.     

Acidification of the electrolyte during the galvanic corrosion of AA7075: A numerical and experimental study

The electrochemical interactions between aluminum alloy 7075 and low-carbon steels under gelled electrolytes were studied. Such electrolytes provided the opportunity to investigate both thick and thin electrolyte systems. The electrolyte was chemically modified to visually track the acidic fronts during the anodic reaction and the subsequent hydrolysis process. Two mathematical models were validated for both thick and ultrathin electrolytes. The acidification of thick electrolytes was extended some millimeters beyond the aluminum alloy surface, whereas the acidic front was localized next to the metallic joint using ultrathin electrolytes. The combination of both numerical and experimental results allows proving (and explaining why) that the acidification process is more aggressive under dilute than under concentrated electrolytes.     

一种植物油中苯并（a）芘含量测定的固相萃取前处理方法

为了建立一种准确性高、成本低的植物油中苯并(a)芘测定的样品前处理方法，基于GB 5009.7—2016以自制氧化铝柱为固相萃取柱，采用单因素试验对称样量、洗脱剂量、洗脱流速、吸附剂存放时间、吸附剂量这5个影响植物油中苯并（a）芘洗脱的因素进行研究，优化前处理条件，并对测定方法进行考察。结果表明：优化的前处理条件为称样量0.100 0 g、洗脱剂量120 mL、吸附剂（氧化铝）量22 g、洗脱流速1滴/2 s、吸附剂存放时间少于12周；方法检出限为0.2 μg/L，样品加标回收率为94.23%～100.00%，RSD为1.20%～7.36%；同一样品测定结果与SGS测定值接近，相对平均偏差为2.36%～3.50%。说明本试验方法测定结果准确，可应用于油脂企业植物油中痕量苯并（a）芘的测定。     

并流控速沉淀法制备纳米α-Bi2O3及其光催化降解苯酚性能研究

以五水合硝酸铋为铋源,氢氧化钠为沉淀剂,通过简单易操作的并流控速沉淀法合成了α-Bi2O3纳米颗粒.同时,利用XRD和SEM分析了所获产品的结构与表面形貌.并选用苯酚作为模拟污染物,利用LC3000型高效液相色谱仪对其进行色谱分析,探究了所合成的纳米α-Bi2O3光催化剂的催化性能.当苯酚的质量分数为100μg·g?1、pH=8、α-Bi2O3投加量为60 mg·L?1时,可见光照射180 min,降解率可达92.6％.通过自由基捕获实验发现,在α-Bi2O3光催化降解苯酚体系中主要活性物种为羟基自由基.