A high-throughput chaotic advection microreactor for preparation of uniform and aggregated barium sulfate nanoparticles

A high-throughput (105.5 g/h) passive four-stage asymmetric oscillating feedback microreactor using chaotic mixing mechanism was developed to prepare aggregated Barium sulfate (BaSO₄) particles of high primary nanoparticle size uniformity. Three-dimensional unsteady simulations showed that chaotic mixing could be induced by three unique secondary flows (i.e., vortex, recirculation, and oscillation), and the fluid oscillation mechanism was examined in detail. Simulations and Villermaux–Dushman experiments indicate that almost complete mixing down to molecular level can be achieved and the prepared BaSO₄ nanoparticles were with narrow primary particle size distribution (PSD) having geometric standard deviation, σ_g, less than 1.43 when the total volumetric flow rate Q_total was larger than 10 ml/min. By selecting Q_total and reactant concentrations, average primary particle size can be controlled from 23 to 109 nm as determined by microscopy. An average size of 26 nm with narrow primary PSD (σ_g = 1.22) could be achieved at Q_total of 160 ml/min.     

Fluid sloshing thermo-mechanical characteristic in a cryogenic fuel storage tank under different gravity acceleration levels

Fluid sloshing usually causes serious safety issues on the dynamic stability and propellant thermal management during the powered-flight phase of launch vehicle. With the wide using of cryogenic propellants, the coupled thermo-mechanical performance during fluid sloshing becomes more prominent. In the present study, one numerical model is established to simulate fluid sloshing by using the VOF method coupled with the mesh motion treatment. The phase change occurring within the tank is considered. Both the experimental validation and mesh sensitivity analysis are made. It shows that present numerical model is acceptable. Based on the developed numerical model, the effect of different super gravity accelerations on fluid sloshing hydrodynamic characteristic is numerically researched. The fluid pressure variation, the sloshing force and sloshing moment, the interface dynamic response and the interface shape variation are investigated, respectively. It shows that the gravity acceleration has caused obvious influences on fluid sloshing characteristic. When the gravity acceleration is higher than 4g₀, fluid sloshing becomes more obvious and must be paid enough attention. With some valuable conclusions obtained, the present work is of great significance for in-depth understanding of fluid sloshing mechanism.     

焦炉前反馈热工控制系统运行实践

焦炉生产是典型的大惯性、非线性、时变快的复杂系统，以“火落温度”为基础的焦炉前反馈热工控制系统，通过立火道温度自动测量与人工测温相关性分析、粗煤气温度测量与火落判断、标准温度的优化等运行实践，达到了自动火落时间判断、标准温度指导、加热和燃烧优化、高低温炉号判别等目的，对于稳定炉温、降低回炉煤气消耗、提高焦炭质量以及推进焦化企业技术进步具有重要意义。     

基于双声表面波器件的引信加速度传感器

In view of the shortcomings of silicon micro acceleration sensor based on piezoresistive effect and capacitance principle, such as temperature drift, low resolution and poor anti-interference ability, a fuze acceleration sensor based on dual SAW devices is proposed. The sensor adopts a dual saw device structure, one is coated with a sensitive film for measurement, the other is an uncoat- ed reference channel for compensation of environmental temperature, pressure, humidity and other factors. The experimental results show that the maximum linear error is only 1.6%, the sensitivity is 54.3Hz/g, and the maximum hysteresis error is less than 1%. Compared with piezoresistive accelerometer and capacitive accelerometer, the linear error of the accelerometer is small, the sensitivi- ty is high, and it has strong anti-interference ability.     

An iterative approach for the discrete‐time dynamic control of Markov jump linear systems with partial information

The , and mixed dynamic output feedback control of Markov jump linear systems in a partial observation context is studied through an iterative approach. By partial information, we mean that neither the state variable x(k) nor the Markov chain θ(k) are available to the controller. Instead, we assume that the controller relies only on an output y(k) and a measured variable coming from a detector that provides the only information of the Markov chain θ(k). To solve the problem, we resort to an iterative method that starts with a state‐feedback controller and solves at each iteration a linear matrix inequality optimization problem. It is shown that this iterative algorithm yields to a nonincreasing sequence of upper bound costs so that it converges to a minimum value. The effectiveness of the iterative procedure is illustrated by means of two examples in which the conservatism between the upper bounds and actual costs is significantly reduced.     

Microwave bandpass filter by feedback interference topology

This paper proposes a signal feedback interference topology to control the characteristics of a coupled line bandpass filter. Control is carried out by varying the ratio of the transmission line parameters of the forward and the feedback couplers. The topology produces a compact filter that does not require a complicated design or fabrication. The results of the insertion and return losses show that the feedback‐controlled design has desirable features in terms of the design frequency, fractional bandwidth, stopband rejection level, roll‐off rate and insertion loss. The test results of the fabricated prototype achieved good agreement with the simulation results of the ideal transmission line design model. Several microwave, modern wireless and mobile/satellite communication systems may benefit from such a filter design due to its compactness and flexibility.     

User idea implementation in open innovation communities: Evidence from a new product development crowdsourcing community

In collaborative crowdsourcing communities for open innovation, users generate and submit ideas as idea co‐creators. Firms then select and implement valuable ideas for new product development. Despite the popularity and success of these open innovation communities, relatively little is known about the factors that determine the implementation of the user‐generated ideas. Based on research on individual creativity, we propose a conceptual model integrating users' previous experience, idea presentation characteristics and feedback valence to explain the likelihood of idea implementation. We validate our research model with a panel data analysis of 43 550 ideas submitted by 16 360 users in the MIUI new product development community hosted by Xiaomi, a large electronics manufacturing company in China. We find an inverted U‐shaped relationship between users' past successful experience and idea implementation. Furthermore, the length of ideas is positively associated with the likelihood of idea implementation. There is also an inverted U‐shaped relationship between supporting evidence and idea implementation. Finally, we demonstrate the negative effect of positive feedback and the positive effect of negative feedback on idea implementation. These findings offer rich insights to understand the phenomenon of open innovation better. Theoretical and practical implications are discussed.     

风洞模型加速度负反馈振动主动控制方法研究

针对尾撑式风洞模型强方向性振动问题,基于异位配置加速度负反馈控制器对风洞模型振动主动控制方法进行研究。首先,通过模态分析得到系统低阶模态振动的强方向性并基于系统特性设计了具有结构耦合性的内嵌压电陶瓷作动器的风洞模型振动主动控制系统。然后,基于异位配置NAF控制器分别设计了针对第二阶模态和前两阶模态的单模态NAF控制算法和双模态NAF控制算法。最后,进行了实验验证,结果表明:双模态NAF控制算法控制效果较好,前两阶模态阻尼比分别提高近13倍和近40倍,镇定时间分别缩短近11s和近26s。     

基于极点配置的推力矢量伺服系统控制策略研究

针对推力矢量伺服系统提出了一种采用状态反馈对系统极点进行配置的方法,同时采用该方法设计了Luenberger状态观测器,在此基础上实现了伺服系统的稳态控制。通过仿真和实验表明,采用该方法设计的推力矢量伺服系统的性能优于基于输出反馈的PI-陷波滤波控制的系统性能。     

Robust predictive extended state observer for a class of nonlinear systems with time-varying input delay

ABSTRACT

This paper deals with asymptotic stabilisation of a class of nonlinear input-delayed systems via dynamic output feedback in the presence of disturbances. The proposed strategy has the structure of an observer-based control law, in which the observer estimates and predicts both the plant state and the external disturbance. A nominal delay value is assumed to be known and stability conditions in terms of linear matrix inequalities are derived for fast-varying delay uncertainties. Asymptotic stability is achieved if the disturbance or the time delay is constant. The controller design problem is also addressed and a numerical example with an unstable system is provided to illustrate the usefulness of the proposed strategy.