基于归一化水体指数及其阈值自适应算法的水体遥感反演效果分析

归一化水体指数（NDWI）是水体遥感反演的一种重要指标，其阈值及修正直接影响反演结果的精度。基于Landsat-8与GF-1光学多光谱影像，使用归一化水体指数法阈值0（TH₀）、最大类间方差法（OTSU）自适应阈值（TH_otsu）与均值漂移聚类算法（Mean-Shift）自适应阈值（TH_MS）分别对典型正常水体、云雾覆盖水体、富营养化水体、高含泥沙水体进行水体遥感提取与效果分析，结果表明：正常水体以TH₀为阈值提取精度最高，THMS提取精度次之，TH_otsu提取精度最差；而云雾覆盖水体、富营养化水体以及含泥沙水体使用THMS提取精度最高，尤其少量云雾覆盖下的水体，TH_MS具有更明显的优势，TH₀提取精度次之，TH_otsu提取精度最差；对于不同的阈值，Land?sat-8比GF-1总体表现出更高的水体提取精度。Mean-Shift算法应用于NDWI阈值修正与水体遥感反演具有快速、水质适应性强、效果稳定的优势，对尤其是复杂条件下的水体信息遥感反演具有较好的提取效果。     

Numerical investigation on the electronic components' cooling for different coolants by finite element method

In this study, we conducted a numerical simulation to examine the cooling performance of an aluminum finned heat sink attached to a silicon chip, placed in a chamber of a rectangular cross-section. The heat sink is cooled by convective heat transfer utilizing nine commercially available gaseous coolants, namely air, hydrogen, helium, nitrogen, oxygen, carbon dioxide, freon12 vapor, propane, and ammonia. To select an appropriate coolant for electronic devices in terms of thermal–hydraulic performance, the maximum temperature on the chip domain and the associated pressure drop in the cooling channel as a function of coolant velocity are analyzed for the aforementioned fluids. It has been found that the minimum temperature is recorded for propane and freon12 vapor, which is approximately 31.1°C, for a coolant velocity of 0.5 m/s, but freon12 vapor shows the highest pressure drop, approximately 900 mPa, among all coolants. In the overall velocity regime, hydrogen shows the best cooling performance in terms of both cooling capacity and hydrodynamic characteristics. But considering safety issues, helium can be a better alternative. This comprehensive study provides a better understanding of different coolant performances, which will aid engineers to develop an effective cooling technique to accommodate the inexorably rising power demand.     

径向弹簧蓄能密封结构最大接触应力的有限元分析

为研究径向弹簧蓄能密封结构的密封特性，针对典型径向弹簧蓄能密封结构，分析其密封机制以及O形弯曲金属螺旋弹簧的弹性特性；采用ANSYS有限元分析软件，建立典型弹簧蓄能密封结构的非线性有限元分析模型，对弹簧蓄能密封圈在不同压缩率、不同介质压力下的接触应力进行分析，研究在多种工况下最大接触应力的变化情况。结果表明：压缩率保持不变时，最大接触应力随着介质压力的增大而增大；介质压力保持不变时，随着压缩率的增大，最大接触应力先增大再减小。对压缩率、介质压力与最大接触应力的关系进行曲线拟合，可用于指导弹簧蓄能密封结构的精确设计。     

Destructive and non-destructive evaluation of concrete for optimum sand to aggregate volume ratio

Aggregates are the biggest contributor to concrete volume and are a crucial parameter in dictating its mechanical properties. As such, a detailed experimental investigation was carried out to evaluate the effect of sand-to-aggregate volume ratio (s/a) on the mechanical properties of concrete utilizing both destructive and non-destructive testing (employing UPV (ultrasonic pulse velocity) measurements). For investigation, standard cylindrical concrete samples were made with different s/a (0.36, 0.40, 0.44, 0.48, 0.52, and 0.56), cement content (340 and 450 kg/m³), water-to-cement ratio (0.45 and 0.50), and maximum aggregate size (12 and 19 mm). The effect of these design parameters on the 7, 14, and 28 d compressive strength, tensile strength, elastic modulus, and UPV of concrete were assessed. The careful analysis demonstrates that aggregate proportions and size need to be optimized for formulating mix designs; optimum ratios of s/a were found to be 0.40 and 0.44 for the maximum aggregate size of 12 and 19 mm, respectively, irrespective of the W/C (water-to-cement) and cement content.     

两次喷射对正丁醇部分预混燃烧影响的试验研究

在一台改造的单缸柴油机上进行了预主喷两次喷射策略对正丁醇部分预混燃烧影响的试验研究。研究结果表明:正丁醇燃料实现部分预混燃烧相对汽油燃料对喷射时刻较敏感,最大压力升高率高,稳定运行范围窄,但未燃碳氢、氮氧化物和碳烟排放较低;预主喷两次喷射能有效降低正丁醇部分预混燃烧最大压力升高率,随着预主喷间隔的增大,最大压力升高率先快速降低后上升,预喷射比例越大,获得最低压力升高率对应的预主喷间隔越大;通过优化预主喷两次喷射策略,能显著改善正丁醇部分预混燃烧可控性差、最大压力升高率高的问题,从而有利于实现更大工况范围内的高效燃烧。     

基于卡尔曼滤波的波浪发电系统反步法最优功率跟踪控制

常规变速控制系统的精度不高,变换器晶闸管开关动作产生的高频纹波较大,为此提出一种基于卡尔曼滤波的反步控制方法。文章通过分析波浪能提取装置的受力及幅频特性,获取了波浪能转化效率最大化的控制条件,并搭建了一套基于卡尔曼滤波的波浪发电反步最优功率控制系统。通过仿真研究了3种控制方法的控制精度和有效性,仿真结果表明:低通滤波反步法存在相位延迟,不能满足最大功率捕获策略的相位条件,影响系统的最终有功功率输出;反步法的跟踪误差较大,导致系统输出的有功功率较低;卡尔曼滤波反步法的动态性能较好,跟踪电流的波形振幅较小,能保证系统全局收敛,在电机速度方向、幅值和频率突变的情况下,仍能快速准确跟踪给定信号,鲁棒性和抗干扰能力更好。     

基于改进卷积神经网络的化纤丝饼表面缺陷识别

针对传统人工检测化纤丝饼表面缺陷方法的不足,提出改进的卷积神经网络对正常以及3种常见缺陷丝饼进行分类识别。首先对采集的丝饼图像进行分块处理,然后利用改进的卷积神经网络进行特征提取,采用全局最大池化层代替全连接层,增强了图像对空间变换的鲁棒性,减少了模型参数,并利用softmax分类器进行分类。最后在网络学习过程中提出主动学习方法,用少量标注样本对网络进行训练,选出对提升网络性能最具价值的样本进行标注并加入到训练样本中进行训练检测。结果表明,该方法可有效实现丝饼的缺陷识别,识别准确率达到97.1%,并有效减少了网络所需的标注样本数量,节省大量的标注成本,具有一定的通用性。     

On the volume power density of radial thermoelectric generators

We examine the volume power density of radial thermoelectric generators (TEGs). Radial, or tubular, TEGs have been considered as an alternative to the usual flat-plate TEGs due to its improved geometric match to typical curved heat sources and high surface power density. However, surface power density is not the only important performance index in realistic situations. Especially for TEGs with inorganic materials that have high raw material prices, volume power density can be important as well. In this note, an analytic model of a radial TEG is studied with a numerical trial-and-error approach for investigating its volume power density. At the same time, an alternative, approximate method of estimating the maximum power of the radial TEG is presented. Using these two approaches, we estimate the volume power density of a skutterudite-based radial TEG and compare the results to those of a flat-plate TEG. The volume power density of the radial TEG is significantly lower than that of the flat-plate TEG. For example, our calculation for a representative case with free convection on the cold side shows that the volume power density of the radial TEG will be 107 W/m³ at best. The result improves with forced convection, and our calculation for a representative case with forced convection on the cold side exhibits the maximum volume power density of 24 100 W/m³ . All these values turn out to be smaller roughly by one order of magnitude than the maximum volume power densities of comparable flat-plate TEGs. Such a low volume power density indicates lower economic feasibility of the radial TEG with expensive inorganic thermoelectric materials. This is also explicitly discussed by presenting the high cost per watt of the radial TEG. It is therefore suggested that radial TEGs with less expensive organic materials may be more acceptable than those with inorganic ones.     

Maximum likelihood-based adaptive differential evolution identification algorithm for multivariable systems in the state-space form

Parameter estimation plays an important role in the field of system control. This article is concerned with the parameter estimation methods for multivariable systems in the state-space form. For the sake of solving the identification complexity caused by a large number of parameters in multivariable systems, we decompose the original multivariable system into some subsystems containing fewer parameters and study identification algorithms to estimate the parameters of each subsystem. By taking the maximum likelihood criterion function as the fitness function of the differential evolution algorithm, we present a maximum likelihood-based differential evolution (ML-DE) algorithm for parameter estimation. To improve the parameter estimation accuracy, we introduce the adaptive mutation factor and the adaptive crossover factor into the ML-DE algorithm and propose a maximum likelihood-based adaptive differential evolution algorithm. The simulation study indicates the efficiency of the proposed algorithms.     

Supporting comprehensible presentation of clone candidates through two-dimensional maximisation

Duplicated code detection has been an active research field for several decades. Although many algorithms have been proposed, only a few researches have focussed on the comprehensive presentation of the detected clones. During the evaluation of clone detectors developed by the authors, it was observed that the results of the clone detectors were hard to comprehend. Therefore, in this paper a broadly suitable grouping method with which clone pairs can be easily grouped together to provide a more compact result is presented. The grouping algorithm is examined and a more precise revised algorithm is proposed to present all of the candidates to the user.