Interfacial microstructure and mechanical properties of Ti3SiC2 ceramic and TC11 alloy joint diffusion bonded with a Cu interlayer

Reliable joints of Ti₃SiC₂ ceramic and TC11 alloy were diffusion bonded with a 50 μm thick Cu interlayer. The typical interfacial structure of the diffusion boned joint, which was dependent on the interdiffusion and chemical reactions between Al, Si and Ti atoms from the base materials and Cu interlayer, was TC11/α-Ti + β-Ti + Ti₂Cu + TiCu/Ti₅Si₄ + TiSiCu/Cu(s, s)/Ti₃SiC₂. The influence of bonding temperature and time on the interfacial structure and mechanical properties of Ti₃SiC₂/Cu/TC11 joint was analyzed. With the increase of bonding temperature and time, the joint shear strength was gradually increased due to enhanced atomic diffusion. However, the thickness of Ti₅Si₄ and TiSiCu layers with high microhardness increased for a long holding time, resulting in the reduction of bonding strength. The maximum shear strength of 251 ± 6 MPa was obtained for the joint diffusion bonded at 850 °C for 60 min, and fracture primarily occurred at the diffusion layer adjacent to the Ti₃SiC₂ substrate. This work provided an economical and convenient solution for broadening the engineering application of Ti₃SiC₂ ceramic.     

Controlled Secure Direct Communication Protocol via the Three-Qubit Partially Entangled Set of States

In this paper, we first re-examine the previous protocol of controlled quantum secure direct communication of Zhang et al.’s scheme, which was found insecure under two kinds of attacks, fake entangled particles attack and disentanglement attack. Then, by changing the party of the preparation of cluster states and using unitary operations, we present an improved protocol which can avoid these two kinds of attacks. Moreover, the protocol is proposed using the three-qubit partially entangled set of states. It is more efficient by only using three particles rather than four or even more to transmit one bit secret information. Given our using state is much easier to prepare for multiqubit states and our protocol needs less measurement resource, it makes this protocol more convenient from an applied point of view.     

Bearing Failure Optimization of Composite Double-Lap Bolted Joints Based on a Three-Step Strategy Marked By Feasible Region Reduction and Model Decoupling

To minimize the mass and increase the bearing failure load of composite doublelap bolted joints, a three-step optimization strategy including feasible region reduction, optimization model decoupling and optimization was presented. In feasible region reduction, the dimensions of the feasible design region were reduced by selecting dominant design variables from numerous multilevel parameters by sensitivity analyses, and the feasible regions of variables were reduced by influence mechanism analyses. In model decoupling, the optimization model with a large number of variables was divided into various sub-models with fewer variables by variance analysis. In the third step, the optimization sub-models were solved one by one using a genetic algorithm, and the modified characteristic curve method was adopted as the failure prediction method. Based on the proposed optimization method, optimization of a double-lap single-bolt joint was performed using the ANSYS^® code. The results show that the bearing failure load increased by 13.5% and that the mass decreased by 8.7% compared with those of the initial design of the joint, which validated the effectiveness of the three-step optimization strategy.     

湖北省保康县荆山玉地球化学特征及其成因分析

荆山玉是湖北省保康县新发现的一个玉石品种,形成于大陆边缘—洋盆区过渡带的热水沉积环境,为晚震旦世—早寒武世灯影组的一种硅质角砾岩:原地震碎角砾岩,由角砾和胶结物二部分构成,角砾局部可拼接;角砾成分为早期硅质岩碎裂产物,胶结物除早期硅质岩碎裂产物外,还有少量后期充填的石英、铁质等,受角砾、胶结物颗粒大小、裂隙发育程度不同的影响,后期热液改造程度不同,角砾和胶结物化学成分存在一定的差异,色调与铁质有关。荆山玉的形成主要经历了三个阶段的演化:第一阶段,低温150～225℃、弱氧化—弱还原条件下热水成因的硅质岩形成;第二阶段,热力膨胀外力作用下,硅质岩局部原地震碎形成硅质角砾岩,热水温度243～340℃,富氧氧化—贫氧过渡环境,红褐色的Fe~(3+)在胶结物、裂隙中富集;第三阶段,热水温度116～127℃、缺氧还原条件,黄色的Fe~(2+)在胶结物、裂隙中富集。     

A facile method for preparation of PGS@ZB‐N and gas‐sol alternating synergistic effect for fire resistance of EVA

Through the simple precipitation of palygorskite (PGS) by zinc borate (ZB) (to make PGS@ZB) and the decoration of PGS@ZB by dodecylamine (N), a novel organic‐inorganic@inorganic hybrid flame retardant of PGS@ZB‐N was prepared and was incorporated with ethylene vinyl acetate copolymer (EVA) to improve its flame retardance. The structure and morphology of PGS@ZB‐N were characterized by Fourier transform infrared (FTIR) spectroscopy, X‐ray diffraction (XRD), and scanning electron microscopy (SEM), and it was confirmed that the PGS@ZB‐N hybrid had been successfully prepared. The flame retardancy and burning behavior of EVA/PGS@ZB‐N/EG (EG = expandable graphite) composite were studied through thermogravimetric analysis (TGA), limiting oxygen index (LOI), UL‐94 (by the vertical burning test), and cone calorimeter test (CCT) characterizations. The prepared EVA/PGS@ZB‐N/EG composite obtained an LOI value of 41.2% with the addition of 30 wt% PGS@ZB‐N/EG. It was found that EVA/PGS@ZB‐N/EG was protected through a gas phase and condensed phase alternating synergistic effect mechanism.     

基于颜色四通道及空间金字塔的鱼类图像检索

随着计算机视觉技术在海洋水产领域中的应用不断加深，鱼类图像检索在渔业资源调查、鱼类行为学分析等方面发挥了巨大的作用。通过研究发现，鱼类图像的背景信息会对鱼类图像检索造成极大干扰，而且鱼类图像中颜色、纹理、形状等特征由于空间位置信息的缺乏而使检索的准确率不高。为解决以上问题，提出了一种新的基于颜色四通道及空间金字塔的鱼类图像检索算法。首先，提取视觉显著性图将鱼类图像的前景和背景分开，从而减少图像背景对检索的干扰；其次，为了使图像特征包含一定的空间位置信息，利用空间金字塔的理论对图像进行分割，在此基础上，将图像转为HSVG四通道图并提取SURF特征；；最后，得到检索结果。为验证所提算法的有效性，在QUT_fish_data数据集和DLOU_fish_data数据集上对算法的查全率、查准率与经典的HSVG算法和显著性分块算法进行对比：在两个数据集上查准率分别比传统的HSVG算法最多分别提高12%和5%，查全率最多分别提高7%和22%；比传统的显著性分块算法查准率最多分别提高15%和5%，查全率最多分别提高36%和22%；从而证明所提算法是有效的，能有效提升鱼类图像的检索效果。