A comparative study on structural,morphological and photocatalytic properties of anodically grown ZnO nanowires under varying parameters

Journal of Materials Science: Materials in Electronics - In this study, zinc oxide (ZnO) nanowires (NWs) were successfully produced on Zn plates through electrochemical anodization in potassium...     

Analyzing the determinants of carbon emissions from transportation in European countries: the role of renewable energy and urbanization

Clean Technologies and Environmental Policy - The continuous growth of transport sector and the increase in carbon emissions from transportation attract the attention of policy makers in...     

HYDRODYNAMIC STUDIES IN A HALF SLOT-RECTANGULAR SPOUTED BED COLUMN

Experiments were carried out in a half slot-rectangular spouted bed to investigate the effects of slot width and lower section basal angle on column hydrodynamics. Flow regimes, minimum spouting velocity, spouting and maximum pressure drops, and maximum spoutable bed height were determined for 4 mm diameter polyethylene particles. The results are compared with those for conventional cylindrical and rectangular spouted beds. Correlations for each hydrodynamic parameter are developed and compared with equations available in the literature.     

One-dimensional partitioning for heterogeneous systems: Theory and practice

We study the problem of one-dimensional partitioning of nonuniform workload arrays, with optimal load balancing for heterogeneous systems. We look at two cases: chain-on-chain partitioning, where the order of the processors is specified, and chain partitioning, where processor permutation is allowed. We present polynomial time algorithms to solve the chain-on-chain partitioning problem optimally, while we prove that the chain partitioning problem is NP-complete. Our empirical studies show that our proposed exact algorithms produce substantially better results than heuristics, while solution times remain comparable.     

A path planning model based on nested regular hexagons using weighted centroid localization

In many wireless sensor network (WSN) applications, the location of a sensor node is crucial for determining where the event or situation of interest occurred. Therefore, localization is one of the critical challenges in WSNs. Mobile anchor node assisted localization (MANAL) is one of the promising solutions for the localization of statically deployed sensors. The main problem in MANAL localization is that the path planning of the mobile anchor (MA) node should be done so that the localization error in the network will be minimal and that all unknown nodes in the network are covered. This paper proposes a new path planning approach called nested hexagons curves (NHexCurves) for MANAL. NHexCurves guarantees that it will receive messages from at least three non-collinear anchors to locate all unknown nodes in the network. The proposed model has compared six different path planning schemes in the literature using weighted centroid localization (WCL). In these comparisons, first of all, localization errors of the models are compared using some statistical concepts. Second, the variation of the localization error according to parameters such as resolution (R) and the standard deviation of noise (σ) is observed. Then, with similar approaches, the standard deviation of errors, localization ratio, scalability performances, and finally, path lengths of the models are examined. The simulation results show that the NHexCurves static path planning model proposed in this study stands out compared to other models with high localization error and localization ratio performance, especially at low resolutions, due to its path design. At the same time, the lowest error values according to σ are obtained with the proposed model among all models considered.     

Electrophoretic deposition of nano-sized BaTiO3

In this study, a non-aqueous method in a simple one pot reaction process was employed to synthesize nano-sized BaTiO₃ particles and then electrophoretic deposition technique was employed for thin film coatings. In the first step of the preparation, metallic barium is directly dissolved in benzyl alcohol at slightly elevated temperatures. Then titanium isopropoxide was added following by a solvothermal treatment. At the end of the reaction, nearly spherical BaTiO₃ nanoparticles were obtained typically 5 nm in diameter. After establishing the stability of the BaTiO₃ suspension in ethanol, electrophoretic deposition process was performed without any additional operation. Alumina with platinum plating was used as substrate. To achieve the optimal process parameters, various voltages were applied by altering the cathode to anode distance as well as deposition time. High voltages application was possible without causing hydrolysis, because of the non-aqueous ethanol medium with higher surface charge of the nanoparticles. The deposited surface coatings were dried in air and sintered at various temperatures. SEM, EDX and XRD analysis were employed for the investigation of the coating.     

Investigation of the Equivalence of National Dew-Point Temperature Realizations in the ?50?°C to +?20?°C Range

In the field of humidity quantities, the first CIPM key comparison, CCT-K6 is at its end. The corresponding European regional key comparison, EUROMET.T-K6, was completed in early 2008, about 4?years after the starting initial measurements in the project. In total, 24 NMIs from different countries took part in the comparison. This number includes 22 EURAMET countries, and Russia and South Africa. The comparison covered the dew-point temperature range from ?50?°C to +20?°C. It was carried out in three parallel loops, each with two chilled mirror hygrometers as transfer standards in each loop. The comparison scheme was designed to ensure high quality results with evenly spread workload for the participants. It is shown that the standard uncertainty due to the long-term instability was smaller than 0.008?°C in all loops. The standard uncertainties due to links between the loops were found to be smaller than 0.025?°C at ?50?°C and 0.010?°C elsewhere. Conclusions on the equivalence of the dew-point temperature standards are drawn on the basis of calculated bilateral degrees of equivalence and deviations from the EURAMET comparison reference values (ERV). Taking into account 16 different primary dew-point realizations and 8 secondary realizations, the results demonstrate the equivalence of a large number of laboratories at an uncertainty level that is better than achieved in other multilateral comparisons so far in the humidity field.     

Mechanical properties and repair bond strength of polymer-based CAD/CAM restorative materials

Information on the mechanical properties and repairability of computer-aided design/computer-aided manufacturing (CAD/CAM) blocks is scarce. Five CAD/CAM blocks with similar indications were evaluated, including four resin nanoceramics, one polymer-infiltrated ceramic network (PICN), and one feldspathic ceramic. CAD/CAM blocks were sectioned into 4 mm × 1.2 mm × 13 mm bars for flexural strength (FS), and 4 mm thick blocks were prepared for elastic modulus (EM), nanohardness (NH), and microshear bond strength (µSBS) testing. FS of the CAD/CAM blocks was determined using a three-point bending test, whereas EM and NH values were measured using a nanoindenter. The reparability of the tested block materials was determined by the µSBS test. One-way ANOVA was conducted for FS, EM, NH, and µSBS followed by Tukey's pairwise comparison (α < 0.05). FS ranged from 115 to 207 MPa, EM from 8.21 to 44 GPa, NH from 0.76 to 7.24, and µSBS from 24.9 to 30.6 MPa. The findings of the present study revealed that resin nanoceramic blocks exhibited higher FS values than PICN and feldspathic ceramic, and they have acceptable mechanical properties for the fabrication of single-unit restorations according to the ISO 6872:2008. Furthermore, all CAD/CAM blocks tested can be successfully repaired regarding their recommended repair protocol.