Identification of Components of the Aggregation Pheromone of the Guam Strain of Coconut Rhinoceros Beetle,Oryctes rhinoceros,and Determination of Stereochemistry

The coconut rhinoceros beetle, Oryctes rhinoceros (Linnaeus 1758) (Coleoptera: Scarabaeidae: Dynastinae) (CRB), is endemic to tropical Asia where it damages both coconut and oil palm. A new invasion by CRB occurred on Guam in 2007 and eradication attempts failed using commonly applied Oryctes rhinoceros nudivirus (OrNV) isolates. This and subsequent invasive outbreaks were found to have been caused by a previously unrecognized haplotype, CRB-G, which appeared to be tolerant to OrNV. The male-produced aggregation pheromone of the endemic, susceptible strain of O. rhinoceros (CRB-S) was previously identified as ethyl 4-methyloctanoate. Following reports from growers that commercial lures containing this compound were not attractive to CRB-G, the aim of this work was to identify the pheromone of CRB-G. Initial collections of volatiles from virgin male and female CRB-G adults from the Solomon Islands failed to show any male- or female-specific compounds as candidate pheromone components. Only after five months were significant quantities of ethyl 4-methyloctanoate and 4-methyloctanoic acid produced by males but not by females. No other male-specific compounds could be detected, in particular methyl 4-methyloctanoate, 4-methyl-1-octanol, or 4-methyl-1-octyl acetate, compounds identified in volatiles from some other species of Oryctes. Ethyl 4-methyloctanoate elicited a strong electroantennogram response from both male and female CRB-G, but these other compounds, including 4-methyloctanoic acid, did not. The enantiomers of ethyl 4-methyloctanoate and 4-methyloctanoic acid were conveniently prepared by enzymatic resolution of the commercially-available acid, and the enantiomers of the acid, but not the ester, could be separated by gas chromatography on an enantioselective cyclodextrin phase. Using this approach, both ethyl 4-methyloctanoate and 4-methyloctanoic acid produced by male CRB-G were shown to be exclusively the (R)-enantiomers whereas previous reports had suggested male O. rhinoceros produced the (S)-enantiomers. However, re-examination of the ester and acid produced by male CRB-S from Papua New Guinea showed that these were also the (R)-enantiomers. In field trapping experiments carried out in the Solomon Islands, both racemic and ethyl (R)-4-methyloctanoate were highly attractive to both male and female CRB-G beetles. The (S)-enantiomer and the corresponding acids were only weakly attractive. The addition of racemic 4-methyloctanoic acid to ethyl 4-methyloctanoate did significantly increase attractiveness, but the addition of (R)- or (S)-4-methyloctanoic acid to the corresponding ethyl esters did not. Possible reasons for the difference in assignment of configuration of the components of the CRB pheromone are discussed along with the practical implications of these results.

     

The binding of orally dosed hydrophobic active pharmaceutical ingredients to casein micelles in milk

Casein proteins (α_S1-, α_S2-, β- and κ-casein) account for 80% of the total protein content in bovine milk and form casein micelles (average diameter = 130 nm, approximately 10¹⁵ micelles/mL). The affinity of native casein micelles with the 3 hydrophobic active pharmaceutical ingredients (API), meloxicam [351.4 g/mol; log P = 3.43; acid dissociation constant (pK_a) = 4.08], flunixin (296.2 g/mol; log P = 4.1; pK_a = 5.82), and thiabendazole (201.2 g/mol; log P = 2.92; pK_a = 4.64), was evaluated in bovine milk collected from dosed Holstein cows. Native casein micelles were separated from raw bovine milk by mild techniques such as ultracentrifugation, diafiltration, isoelectric point precipitation (pH 4.6), and size exclusion chromatography. Acetonitrile extraction of hydrophobic API was then done, followed by quantification using HPLC-UV. For the API or metabolites meloxicam, 5-hyroxy flunixin and 5-hydroxy thiabendazole, 31 ± 3.90, 31 ± 1.3, and 28 ± 0.5% of the content in milk was associated with casein micelles, respectively. Less than ～5.0% of the recovered hydrophobic API were found in the milk fat fraction, and the remaining ～65% were associated with the whey/serum fraction. A separate in vitro study showed that 66 ± 6.4% of meloxicam, 29 ± 0.58% of flunixin, 34 ± 0.21% of the metabolite 5-hyroxy flunixin, 50 ± 4.5% of thiabendazole, and 33 ± 3.8% of metabolite 5-hydroxy thiabendazole was found partitioned into casein micelles. Our study supports the hypothesis that casein micelles are native carriers for hydrophobic compounds in bovine milk.     

Effect of high-pressure-jet processing on the viscosity and foaming properties of pasteurized whole milk

The processing of milk using high-pressure technologies has been shown to dissociate casein micelles, denature whey proteins, and change the appearance and rheological properties of milk. A novel high-pressure processing technology called high-pressure-jet (HPJ) processing is currently being investigated for use in the food industry. Few studies have evaluated the effects of HPJ technology on dairy foods. The present study investigated the physicochemical and foaming properties of homogenized pasteurized whole milk processed at pressures from 0 to 500 MPa using HPJ processing. The apparent particle size exhibited a monomodal distribution in whole milk samples processed up to 125 MPa and a bimodal distribution for samples processed at 250, 375, and 500 MPa. The viscosity increased from approximately 2 to 5 mPa·s when whole milk was processed using HPJ at 375 MPa, and foam expansion increased from approximately 80 to 140% after processing at >125 MPa. Foam stability was limited to pressures in the 375 to 500 MPa range. We hypothesized that the increase in apparent particle size was due to the dissociation of casein micelles into surface-active casein protein monomers, and the formation of casein–casein and casein–fat particles. Ultracentrifugation of samples into 3 milk fractions (supernatant, serum, and precipitate), and subsequent fat and protein analysis on the 3 fractions, showed that a strong interaction between casein proteins and fat triglycerides occurred, evidenced by the increase in fat content associated with the precipitate fraction with increasing pressure. This suggests that stable casein–fat aggregates are formed when whole milk is processed using HPJ at pressure >125 MPa.     

Improved Controlled-Release Formulations for a New Trap Design for Male Mediterranean Fruit Flies: The C&C Trap

The Mediterranean fruit fly, Ceratitis capitata, is a major pest of fruits and vegetables in the world. With the help of an extensive trapping program, the continental United States has remained free of established medfly populations. In an effort to increase trapping efficiency, controlled-release polymeric panels with trimedlure and ceralure were developed in conjunction with the development of a new trap, the C&C trap. This study contrasts the effectiveness of different panel formulations with the standard trimedlure polymeric plug and describes the use of the panels in the C&C trap. Field tests in Hawaii using released sterile flies showed consistently higher male medfly catches with panels in C&C traps than with the standard trimedlure polymeric plug in Jackson traps.     

An exergy method for compressor performance analysis

An exergy method for compressor performance analysis is presented. The purpose of this is to identify and quantify defects in the use of a compressor's shaft power. This information can be used as the basis for compressor design improvements. The defects are attributed to friction, irreversible heat transfer, fluid throttling, and irreversible fluid mixing. They are described, on a common basis, as exergy destruction rates and their locations are identified. The method can be used with any type of positive displacement compressor. It is most readily applied where a detailed computer simulation program is available for the compressor. An analysis of an open reciprocating refrigeration compressor that used R12 refrigerant is given as an example. The results that are presented consist of graphs of the instantaneous rates of exergy destruction according to the mechanisms involved, a pie chart of the breakdown of the average shaft power wastage by mechanism, and a pie chart with a breakdown by location.     

High‐pressure processing effects on the mechanical,barrier and mass transfer properties of food packaging flexible structures: a critical review

Food products can be high‐pressure processed (HPP) either in bulk or prepackaged in flexible or semi‐rigid packaging materials. In the latter case the packaging material is subjected, together with the food, to high‐pressure treatment. A number of studies have been performed to quantify the effects of high‐pressure processing on the physical and barrier properties of the packaging material, since the integrity of the package during and after processing is of paramount importance to the safety and quality of the food product. This article reviews the results of published research concerning the effect of HPP on packaging materials. Copyright © 2004 John Wiley & Sons, Ltd.     

Effect of water on the oxygen barrier properties of poly(ethylene terephthalate) and polylactide films

The aim of this work was to study the variations in the oxygen diffusion, solubility, and permeability coefficients of polylactide (PLA) films at different temperatures (5, 23, and 40°C) and water activities (0–0.9). The results were compared with the oxygen diffusion, solubility, and permeability coefficients obtained for poly(ethylene terephthalate) (PET) films under the same experimental conditions. The water sorption isotherm for PLA films was also determined. Diffusion coefficients were determined with the half‐sorption time method. Also, a consistency test for continuous‐flow permeability experimental data was run to obtain the diffusion coefficient with the lowest experimental error and to confirm that oxygen underwent Fickian diffusion in the PLA films. The permeability coefficients were obtained from steady‐state permeability experiments. The results indicated that the PLA films absorbed very low amounts of water, and no significant variation of the absorbed water with the temperature was found. The oxygen permeability coefficients obtained for PLA films (2–12 × 10^?18 kg m/m² s Pa) were higher than those obtained for PET films (1–6 × 10^?19 kg m/m² s Pa) at different temperatures and water activities. Moreover, the permeability coefficients for PLA and PET films did not change significantly with changes in the water activity at temperatures lower than 23°C. © 2004 Wiley Periodicals, Inc. J Appl Polym Sci 92: 1790–1803, 2004     

Large-scale cooling towers as part of an efficient and cleaner energy generating technology

The present paper will outline the main aspects of the design and construction of cooling towers in Germany in the last decade. As part of electricity generating power plants, cooling towers play a significant role for the availability of reliable energy supplies, in a manner compatible with environmental requirements. They definitely belong to the largest and thinnest concrete structures at present. Because of the combined action of wind, thermal and moisture effects, special care has to be taken with regard to fatigue, cracking and corrosion to ensure an adequate level of safety and durability. Such a design strategy has been employed for the world’s tallest cooling tower at the Niederaussem power plant in Germany, with an overall height of 200 m and thickness values of 22–24 cm. Special considerations included the realistic non-axisymmetric distribution of soil characteristics, wind action due to interference effects (as determined by wind-tunnel tests), optimisation of the shell shape to improve structural and dynamic behaviour, injection of the cleaned flue-gas into the cooling tower, and the use of high-performance concrete (85 MPa) to improve shell resistance against acid attack by the cleaned flue-gas. The paper will present some results of an actual research project on this problem, which was conducted at the University of Wuppertal, to explore the use of high-performance concrete on design, stability and durability of cooling tower shells.