Depassivation and repassivation of stainless steels by stepwise pH change

Immersion tests with different stainless steels have been performed, while the pH was stepwise decreased and then increased again. During 8.5-day exposure, the depassivation and repassivation pH values as a function of pitting resistance equivalent number were determined. There is always a gap between both pH values (depassivation and repassivation), indicating that for every steel, there are conditions where an existing passive layer can be maintained but cannot be rebuilt after depassivation. In such environments, the passive layer is thicker, consisting mainly of molybdenum and iron rich oxides, while chromium is dissolved. Usually, depending on conditions, the passive layer is more chromium-rich, especially the inner layer. This is relevant, for example, for acidizing jobs in oil and gas industry, proving that repassivation after acidizing will happen promptly, when the pH is increased again.     

Electrochemical routes for environmentally friendly recycling of rare-earth-based (Sm–Co) permanent magnets

Journal of Applied Electrochemistry - The consumption of critical raw materials, especially those in permanent magnets of Nd–Fe–B and Sm–Co-type, has significantly grown in the...     

高山庇护所 斯诺文尼亚

<正>建设单位:PD Ljubljana Matica项目计划:庇护所结构工程:AKT II, Hanif Kara, Edward Wilkes实施及现场协调:PD Ljubljana Matica,Matevz Jerman, Davor Rozman项目情况:2016年竣工主承包商:Permiz d.o.o., Bostjan Perme OFIS和AKT II的建筑师同哈佛大学设计研究生院、Freeaproved、PD Ljubljana Matica、Rieder和Rockwool的学生合作完成了这个项目。     

Nanolayer CrAlN/TiSiN coating designed for tribological applications

With the goal to produce a hard and tough coating intended for tribological applications, CrAlN/TiSiN nanolayer coating was prepared by alternative deposition of CrAlN and TiSiN layers. In the first part of the article, a detailed study of phase composition, microstructure, and layer structure of CrAlN/TiSiN coating is presented. In the second part, its mechanical properties, fracture and tribological behavior are compared to the nanocomposite TiSiN coating. An industrial magnetron sputtering unit was used for coating deposition. X-ray photoelectron spectroscopy, energy dispersive X-ray spectroscopy, X-ray diffraction, scanning electron microscopy, and transmission electron microscopy were used for compositional and microstructural analysis. Mechanical properties and fracture behavior were studied by instrumented indentation and focused ion beam techniques. Tribological properties were evaluated by ball-on-disk test in a linear reciprocal mode. A complex layer structure was found in the nanolayer coating. The TiSiN layers were epitaxially stabilized inside the coating which led to formation of dislocations at interfaces, to introduction of disturbances in the coating growth, and as a result, to development of fine-grained columnar microstructure. Indentation load required for the onset of fracture was twice lower for the nanolayer CrAlN/TiSiN, compared to the nanocomposite TiSiN coating. This agrees very well with their mechanical properties, with H³/E² being twice higher for the TiSiN coating. However, the nanolayer coating experienced less severe damage, which had a strong impact on tribological behavior. A magnitude of order lower wear rate and four times lower steady state friction coefficient were found for the nanolayer coating.     

Layout design of manufacturable quantum-dot cellular automata

Quantum-dot cellular automaton (QCA) is an emergent technology that is not hindered by quantum effects that limit the scaling of CMOS technology, but instead employs them to perform computation. However, this brings its own impediments, such as the influence of the thermodynamic effects. Beside that, QCA has to be coupled with CMOS circuitry of different size features to enable clocking. We discussed all these facts and devised a floorplan which would facilitate manufacturability. Based on it we developed the process of QCA layout design and defined the design rules that must be considered in order to ensure correct operation. These instructions enable the automatization of designing a QCA circuit layout.     

Internalization and Accumulation in Dendritic Cells of a Small pH‐Activatable Glycomimetic Fluorescent Probe as Revealed by Spectral Detection

DC‐SIGN, an antigen‐uptake receptor in dendritic cells (DCs), has a clear role in the immune response but, conversely, can also facilitate infection by providing entry of pathogens into DCs. The key action in both processes is internalization into acidic endosomes and lysosomes. Molecular probes that bind to DC‐SIGN could thus provide a useful tool to study internalization and constitute potential antagonists against pathogens. So far, only large molecules have been used to directly observe DC‐SIGN‐mediated internalization into DCs by fluorescence visualization. We designed and synthesized an appropriate small glycomimetic probe. Two particular properties of the probe were exploited: activation in a low‐pH environment and an aggregation‐induced spectral shift. Our results indicate that small glycomimetic molecules could compete with antigen/pathogen for binding not only outside but also inside the DC, thus preventing the harmful action of pathogens that are able to intrude into DCs, for example, HIV‐1.     

Effects of international collaboration and status of journal on impact of papers

This study examines the effect of international collaboration of Slovenian authors and the status of journals where papers are published (as determined by their impact factors) on the impact of papers as measured by the number of citations papers receive. Research programme groups working in Slovenia in the 2004–2008 period in the fields of physics, chemistry, biology, biotechnology, and medical science were used for analyses. The results of the analyses show that the effects of the two factors differ among the fields. We discuss possible reasons for this, including the possibility that differences are the result of Slovenia’s science policy.