Optical-luminescence properties of ZnO and TiO2 nanopowders obtained by pulsed laser reactive ablation

Journal of Materials Science: Materials in Electronics - The ZnO and TiO2 nanopowders have been prepared by means of the pulsed laser reactive ablation of metallic (Zn, Ti) targets. The Structural,...     

Magnetothermoelastic Interaction in a Rod of Finite Length Subjected to Moving Heat Sources Via Eringen’s Nonlocal Model

Journal of Engineering Physics and Thermophysics - The generalized nonlocal thermoelastic model in the context of Eringen’s nonlocal elasticity is applied to investigate the...     

Annealing of Mineral-Like Host Matrices for High-Level Waste Immobilization

Inorganic Materials - We have studied the effect of annealing on the chemical and physical properties of mineral-like host matrices for immobilization of the rare-earth–actinide fraction from...     

Probabilistic learning on manifolds (PLoM) with partition

The probabilistic learning on manifolds (PLoM) introduced in 2016 has solved difficult supervised problems for the “small data” limit where the number N of points in the training set is small. Many extensions have since been proposed, making it possible to deal with increasingly complex cases. However, the performance limit has been observed and explained for applications for which N is very small and for which the dimension of the diffusion-map basis is close to N. For these cases, we propose a novel extension based on the introduction of a partition in independent random vectors. We take advantage of this development to present improvements of the PLoM such as a simplified algorithm for constructing the diffusion-map basis and a new mathematical result for quantifying the concentration of the probability measure in terms of a probability upper bound. The analysis of the efficiency of this extension is presented through two applications.     

Use of by-Product Gasoline Fractions Produced by Combining Fuel and Petrochemical Production

Chemistry and Technology of Fuels and Oils - This article considers the alternatives for treatment of the raffinate produced at a unit for the extraction of benzene-containing fractions and the...     

MHD mixed convection of a Cu–water nanofluid flow through a channel with an open trapezoidal cavity and an elliptical obstacle

In the current work, numerical simulations are achieved to study the properties and the characteristics of fluid flow and heat transfer of (Cu–water) nanofluid under the magnetohydrodynamic effects in a horizontal rectangular canal with an open trapezoidal enclosure and an elliptical obstacle. The cavity lower wall is grooved and represents the heat source while the obstacle represents a stationary cold wall. On the other hand, the rest of the walls are considered adiabatic. The governing equations for this investigation are formulated, nondimensionalized, and then solved by Galerkin finite element approach. The numerical findings were examined across a wide range of Richardson number (0.1 ≤ Ri ≤ 10), Reynolds number (1 ≤ Re ≤ 125), Hartmann number (0 ≤ Ha ≤ 100), and volume fraction of nanofluid (0 ≤ φ ≤ 0.05). The current study's findings demonstrate that the flow strength increases inversely as the Reynolds number rises, which pushes the isotherms down to the lower part of the trapezoidal cavity. The Nu_avg rises as the Ri rise, the maximum Nu_avg = 10.345 at Ri = 10, Re = 50, ϕ = 0.05, and Ha = 0; however, it reduces with increasing Hartmann number. Also, it increase by increasing ϕ, at Ri = 10, the Nu_avg increased by 8.44% when the volume fraction of nanofluid increased from (ϕ = 0–0.05).     

Dissolution Kinetics of Nickel(II) Hydroxide in a Mixed Ammonia–Carbonate Solution

Theoretical Foundations of Chemical Engineering - The reaction of nickel(II) hydroxide and a mixed ammonia–carbonate solution to form nickel(II) aqua–ammonia complexes is studied in the...     

Direct ink writing of vancomycin-loaded polycaprolactone/ polyethylene oxide/ hydroxyapatite 3D scaffolds

Novel inks were formulated by dissolving polycaprolactone (PCL), a hydrophobic polymer, in organic solvent systems; polyethylene oxide (PEO) was incorporated to extend the range of hydrophilicity of the system. Hydroxyapatite (HAp) with a weight ratio of 55–85% was added to the polymer-based solution to mimic the material composition of natural bone tissue. The direct ink writing (DIW) technique was applied to extrude the formulated inks to fabricate the predesigned tissue scaffold structures; the influence of HAp concentration was investigated. The results indicate that in comparison to other inks containing HAp (55%, 75%, and 85%w/w), the ink containing 65% w/w HAp had faster ink recovery behavior; the fabricated scaffold had a rougher surface as well as better mechanical properties and wettability. It is noted that the 65% w/w HAp concentration is similar to the inorganic composition of natural bone tissue. The elastic modulus values of PCL/PEO/HAp scaffolds were in the range of 4–12 MPa; the values were dependent on the HAp concentration. Furthermore, vancomycin as a model drug was successfully encapsulated in the PCL/PEO/HAp composite scaffold for drug release applications. This paper presents novel drug-loaded PCL/PEO/HAp inks for 3D scaffold fabrication using the DIW printing technique for potential bone scaffold applications.     

Experimental Verification of a Heat Store Model

Russian Engineering Research - A mathematical model of a heat store based on melting of the working medium is verified by means of an experiment. The model describes a heat store containing a...