Treatment of phenol formaldehyde production wastewater by electrooxidation-electrofenton successive processes

ABSTRACT

Treatments of phenol formaldehyde producing wastewater (PFPW) by electrooxidation (EO) and electro-Fenton (EF) successive processes were carried out in a batch electrolytic reactor using graphite (Gr) and stainless steel (Ss) electrodes. After the completion of the EO process, the wastewater was further treated with EF process. The influence of operating variables such as current density, operating time, initial pH_i and H₂O₂ concentration was evaluated for removals of phenol, TOC and COD in PFPW. Gr/Gr, Gr/Ss or Ss/Ss and Ss/Gr electrode pair were used as anode and cathode. The best removal efficiency in the EO process was obtained with Gr/Gr (93%) as compared to Gr/Ss (82%), Ss/Ss (63%) and Ss/Gr (55%). The removal efficiencies for the EO process using Gr-Gr electrode pair were obtained as 93% for phenol, 61% for COD and 44% for TOC at initial pH_i 7,5 g/L of NaCl, 50 mA/cm² and 5 h. In the EF process, the removal efficiencies at pH_i 3,5 mA/cm² and 30 mM H₂O₂ and 45 min were 100% for phenol, 76% for COD and 59% for TOC. This study provided that the successive processes are an effective method for the removal of phenolic compounds from the wastewater.     

Synthesis and characterization of Al2O3 nanopowders by a simple chitosan-polymer complex solution route

Al₂O₃ nanopowders were synthesized by a simple chitosan-polymer complex solution route. The precursors were calcined at 800–1200 °C for 2 h in air. The prepared samples were characterized by XRD, FTIR and TEM. The results showed that for the precursors prepared with pH 3–9 γ-Al₂O₃ and δ-Al₂O₃ are the two main phases formed after calcination at 800–1000 °C. Interestingly, when the precursor prepared with pH 2 was used, α-Al₂O₃ was formed after calcination at 1000 °C, and pure α-Al₂O₃ was obtained after calcination at 1200 °C. The crystallite sizes of the prepared powders were found to be in the range of 4–49 nm, as evaluated by the XRD line broadening method. TEM investigation revealed that the Al₂O₃ nanopowders consisted of rod-like shaped particles and nanospheres with particle sizes in the range of 10–300 nm. The corresponding selected-area electron diffraction (SAED) analysis confirmed the formation of γ- and α-Al₂O₃ phases in the samples.     

Activated carbons derived from sugarcane bagasse for high-capacitance electrical double layer capacitors

Activated carbon (AC) from sugarcane bagasse was prepared using a simple two-step method of carbonization and chemical activation with four different activating agents (HNO₃, H₂SO₄, NaOH, and KOH). Amorphous carbon structure as identified by X-ray diffraction was observed in all samples. Scanning electron microscopy revealed that the AC had more porosity than the non-activated carbon (non-AC). Specific capacitance of the non-AC electrode was 32.58 F g^?1 at the current density of 0.5 A g^?1, whereas the AC supercapacitor provided superior specific capacitances of 50.25, 69.59, 109.99, and 138.61 F g^?1 for the HNO₃ (AC-HNO₃), H₂SO₄ (AC-H₂SO₄), NaOH (AC-NaOH), and KOH (AC-KOH) activated carbon electrodes, respectively. The AC-KOH electrode delivered the highest specific capacitance (about 4 times of the non-AC electrode) because of its good surface wettability, the largest specific surface area (1058.53 m² g^?1), and the highest total specific pore volume (0.474 cm³ g^?1). The AC-KOH electrode also had a great capacitance retention of almost 100% after 1000 GCD cycles. These results demonstrate that our AC developed from sugarcane bagasse has a strong potential to be used as high stability supercapacitor electrode material.

     

Influence of SCN− moiety on CH3NH3PbI3 perovskite film properties and the performance of carbon-based hole-transport-layer-free perovskite solar cells

Journal of Materials Science: Materials in Electronics - CH3NH3PbI3 perovskite films were prepared via a hot-casting method using six different CH3NH3I, PbI2 and Pb(SCN)2 solutions. Surface...     

Influences of magnesium particles incorporated on electrophoretically multiwall carbon nanotube film on dye-sensitized solar cell performance

Multiwall carbon nanotube (MWCNT) films are prepared on a conductive substrate by electrophoretic deposition. The thickness of MWCNT films is found to increase with the carbon nanotube concentration and the deposition duration. Scanning electron microscopy and energy dispersive X-ray measurements detect magnesium particles incorporated on the MWCNT films. The performance of dye-sensitized solar cell using the electrophoretically MWCNT films as a counter electrode shows a relationship dependent on the film thickness and the amount of magnesium loading. The increase in the magnesium loading on carbon films diminishes the solar cell efficiency. This is because magnesium particles cover the carbon nanotube surface reducing the nanotube catalytic sites and blocking electron transfer to tri-iodide (I₃⁻) ions.