Impact of spinel forming systems (Fe-/Mg-/Mn-Al-O) as functional coating materials for carbon-bonded alumina filters on steel melt filtration

Since solid, non-metallic inclusions influence considerably the quality of casted steel products, carbon-bonded alumina foam filters are used in secondary metallurgical treatments to remove these particles from steel melts. In order to attain a significant improvement of the filtration process, five different carbonaceous spinel compounds from the Fe-/Mg-/Mn-Al-O systems are applied on carbon-bonded alumina filters in this study and investigated with regard of their filtration efficiency. However, these spinel compounds decompose partially during sintering at 1400?°C under reducing atmosphere, wherefore the resulting coatings contain not only spinel compounds, but also oxidic and metallic components. The subsequent interaction with molten steel leads to the development of multicrystal structures on the filter surface, which stem from interfacial reactions between coating materials, molten steel, and inclusions. As a result of this procedure, a reduction of almost 60% alumina inclusions is measured with the aid of an automatic SEM, whereby spinel compounds from the Fe-Mn-Al-O system achieve highest filtration efficiencies.     

Evaluation of dynamic modulus measurement for C/C-SiC composites at different temperatures

The determination of elastic properties at application temperature is fundamental for the design of fibre reinforced ceramic composite components. An attractive method to characterize the flexural modulus at room and high temperature under specific atmosphere is the nondestructive Resonant Frequency Damping Analysis (RFDA). The objective of this paper was to evaluate and validate the modulus measurement via RFDA for orthotropic C/C-SiC composites at the application temperature. At room temperature flexural moduli of C/C-SiC with 0/90° reinforcement were measured under quasi-static 4-point bending loads and compared with dynamic moduli measured via RFDA longitudinally to fibre direction. The dynamic modulus of C/C-SiC was then measured via RFDA up to 1250°C under flowing inert gas and showed an increase with temperature which fitted with literature values. The measured fundamental frequencies were finally compared to those resulting from numerical modal analyses. Dynamic and quasi-static flexural moduli are comparable and the numerical analyses proved that bending modes are correctly modeled by means of dynamic modulus measured via RFDA. The nondestructive RFDA as well as the numerical modeling approach are suitable for evaluation of C/C-SiC and may be transferred to other fibre reinforced ceramic composite materials.     

Comparative performance of carbon nanotube and nanoclay on thermal properties and flammability behavior of amorphous polyamide/SEBS blend

Multiwall carbon nanotubes (CNT) or montmorillonite clay (MMT-30B) were added to a poly(hexamethylene isophthalamide-co-terephthalamine) (an amorphous polyamide - aPA) and styrene-ethylene/butylene-styrene graphitized with maleic anhydride (SEBS) blend, in different concentrations, in order to investigate the morphology, thermal properties and flammability behavior. Different nanoparticle localizations in the phase blend were observed through transmission electronic microscopy. CNT nanoparticles are localized in SEBS phase, and MMT-30B nanoparticles in aPA phase. No significant changes were observed on transition temperatures and thermal stability with both nanoparticle additions. However, a slight increase on storage modulus for clay nanocomposites and a slight reduction for carbon nanotube nanocomposites were observed, due to their different phase localizations. Regarding flammability, CNT nanocomposites showed better performance as a flame retardant when compared to samples with MMT-30B. Although the MMT-30B nanocomposites could not be classified according to the UL-94 criteria, no dripped flaming particles were observed, due to the a char barrier formation on the polymer surface. The CNT nanocomposites were classified according to the UL-94 criteria as V-2. The CNT's selective localization on the SEBS phase decreases its heat-release rate, but no interconnected network structure was formed in the matrix to suppress the dripping flaming particles.     

Lignin from Annual Plants as Raw Material Source for Flavors and Basic Chemicals

The enzymatic conversion of lignins, possibly in combination with electrochemical oxidation, makes aromatics such as syringol, guaiacol, vanillin and catechol available in the qualities required by the fragrance industry. The lignins were obtained by soda digestion from wheat straw and Miscanthus, characterized and then converted with laccases. The overall yield amounted up to 9 wt % with a product spectrum confined to four substances. Catechol was the major product, with a fraction of ≈75 %. It can easily be isolated by extraction with acetone.     

Sintering behavior,microstructure and thermoelectric properties of calcium cobaltite thick films for transversal thermoelectric multilayer generators

The sintering behavior and the thermoelectric performance of Ca₃Co₄O₉ multilayer laminates were studied, and a multilayer thermoelectric generator was fabricated. Compacts and multilayer samples with anisotropic microstructure and residual porosity were obtained after conventional sintering at 920 °C, whereas dense and isotropic multilayer samples were prepared by firing at 1200 °C and reoxidation at 900 °C. A hot-pressed sample has a dense and anisotropic microstructure. Samples sintered at 920 °C exhibit low electrical conductivity due to the low density, whereas the Seebeck coefficient is not sensitive to preparation conditions. However, thermal conductivity of multilayers is very low, and, hence acceptable ZT values are obtained. A transversal multilayer thermoelectric generator (TMLTEG) was fabricated by stacking layers of Ca₃Co₄O₉ green tapes, AgPd conductor printing, and co-firing at 920 °C. The TMLTEG has a power output of 3 mW at ΔT = 200 K in the temperature interval of 25 °C to 300 °C.     

Tetrahydroindoles as Multipurpose Screening Compounds and Novel Sirtuin Inhibitors

Indoles are privileged structures in medicinal and bioorganic chemistry that are particularly well suited to serve as platforms for diversity. Among many other therapeutic areas, the indole scaffold has been used to design aromatic compounds useful to interfere with enzymes engaged in the regulation of substrate acylation status, such as sirtuins. However, the planarity of the indole ring is not necessarily optimal for all target enzymes, especially when functionalization with aromatic side chains is required. Replacement of flat scaffolds by nonplanar molecular cores dominated by sp³ hybridization is a common strategy to avoid the disadvantages associated with poor solubility and high promiscuity, while covering less-well-explored areas of chemical space. Thus, we synthesized fragment-like tetrahydroindoles suitable for fragment-based drug discovery as well as a well-characterized small library intended as multipurpose screening compounds. For proof of principle, these compounds were screened against sirtuins 1–3, enzymes known to be addressable by indoles. We found that 2,6,6-trimethyl-4-oxo-4,5,6,7-tetrahydro-1H-indole-3-carboxamides are potent and selective SIRT2 inhibitors. Compound 16 t displayed an IC₅₀ value of 0.98 μm and could serve as exquisite starting point for hit-to-lead profiling.     

Tunable colors and conductivity by electroless growth of Cu/Cu2O particles on sol-gel modified cellulose

Nano Research - Development of colored surfaces by formation of nano-structured aggregates is a widely used strategy in nature to color lightweight structures (e.g. butterflies) without the use of...     

A greedy reduced basis scheme for multifrequency solution of structural acoustic systems

The solution of frequency dependent linear systems arising from the discretization of vibro-acoustic problems requires a significant computational effort in the case of rapidly varying responses. In this paper, we review the use of a greedy reduced basis scheme for the efficient solution in a frequency range. The reduced basis is spanned by responses of the system at certain frequencies that are chosen iteratively based on the response that is currently worst approximated in each step. The approximations at intermediate frequencies as well as the a posteriori estimations of associated errors are computed using a least squares solver. The proposed scheme is applied to the solution of an interior acoustic problem with boundary element method (BEM) and to the solution of coupled structural acoustic problems with finite element method and BEM. The computational times are compared to those of a conventional frequencywise strategy. The results illustrate the efficiency of the method.