Reconstructed Water Oxidation Electrocatalysts: The Impact of Surface Dynamics on Intrinsic Activities

Electroreduction of small molecules such as H₂O, CO₂, and N₂ for producing clean fuels or valuable chemicals provides a sustainable approach to meet the increasing global energy demands and to alleviate the concern on climate change resulting from fossil fuel consumption. On the path to implement this purpose, however, several scientific hurdles remain, one of which is the low energy efficiency due to the sluggish kinetics of the paired oxygen evolution reaction (OER). In response, it is highly desirable to synthesize high-performance and cost-effective OER electrocatalysts. Recent advances have witnessed surface reconstruction engineering as a salient tool to significantly improve the catalytic performance of OER electrocatalysts. In this review, recent progress on the reconstructed OER electrocatalysts and future opportunities are discussed. A brief introduction of the fundamentals of OER and the experimental approaches for generating and characterizing the reconstructed active sites in OER nanocatalysts are given first, followed by an expanded discussion of recent advances on the reconstructed OER electrocatalysts with improved activities, with a particular emphasis on understanding the correlation between surface dynamics and activities. Finally, a prospect for clean future energy communities harnessing surface reconstruction-promoted electrochemical water oxidation will be provided.     

Substrate temperature-controlled precursor reaction mechanism of PEALD-deposited MoOx thin films

Journal of Materials Science - Molybdenum oxide (MoOx) films had been grown by using plasma-enhanced atomic layer deposition (PEALD) with Mo(CO)6 precursor and O2 plasma reactant in a substrate...     

磨料有序排布电镀砂轮的制备及其把持力研究

为解决电镀砂轮磨削加工中容屑空间不足的问题，采用点胶微粘接的方法制备了磨料有序排布的电镀砂轮，分析了磨料粘接效果和镀层力学性能。通过SEM分析了磨料/镀层/导电胶的结合界面，并进行了干磨削试验。研究结果表明，直径约为磨料粒径40%的胶点可粘接住磨料，单个胶点上粘接多颗磨料的占比小于6%；双脉冲电镀工艺制备的镀层显微硬度大于500HV，表层残余应力小于100MPa，磨料/镀层/导电胶之间的界面贴合紧密，无明显缺陷；砂轮在磨削时没有出现磨料脱落现象。     

Advances in statistical mechanics of rock masses and its engineering applications

To efficiently link the continuum mechanics for rocks with the structural statistics of rock masses,a theoretical and methodological system called the statistical mechanics of rock masses(SMRM)was developed in the past three decades.In SMRM,equivalent continuum models of stressestrain relationship,strength and failure probability for jointed rock masses were established,which were based on the geometric probability models characterising the rock mass structure.This follows the statistical physics,the continuum mechanics,the fracture mechanics and the weakest link hypothesis.A general constitutive model and complete stressestrain models under compressive and shear conditions were also developed as the derivatives of the SMRM theory.An SMRM calculation system was then developed to provide fast and precise solutions for parameter estimations of rock masses,such as full-direction rock quality designation(RQD),elastic modulus,Coulomb compressive strength,rock mass quality rating,and Poisson’s ratio and shear strength.The constitutive equations involved in SMRM were integrated into a FLAC3D based numerical module to apply for engineering rock masses.It is also capable of analysing the complete deformation of rock masses and active reinforcement of engineering rock masses.Examples of engineering applications of SMRM were presented,including a rock mass at QBT hydropower station in northwestern China,a dam slope of Zongo II hydropower station in D.R.Congo,an open-pit mine in Dexing,China,an underground powerhouse of Jinping I hydropower station in southwestern China,and a typical circular tunnel in Lanzhou-Chongqing railway,China.These applications verified the reliability of the SMRM and demonstrated its applicability to broad engineering issues associated with jointed rock masses.     

木片筛余物高得率半化学法清洁制浆技术研究

以太阳纸业备料车间木片筛选碎料（筛余物）为原料，对其烧碱法半化学制浆的实验室工艺和生产试验进行了研究。结果表明，筛余物采用半化学法制浆可获得较高得率和环压强度的纸浆，且用碱量对纸浆性能有显著影响。相对8%NaOH （相对于绝干原料）化学预处理，采用14%NaOH化学预处理结合两段浆浓22%的高浓磨浆工艺，所制半化学浆抄造浆张的裂断长和环压指数分别达2.89 km和9.76 N·m/g，是前者的1.9倍和1.2倍，而且优于现用国内OCC废纸浆抄造浆张；生产试验得到的浆张性能指标与实验室相吻合，其中紧度和环压强度分别达到GB/T 13023—2008瓦楞芯（原）纸AA级和A级优等品要求。     

Evolution of Local Structural Ordering and Chemical Distribution upon Delithiation of a Rock Salt–Structured Li1.3Ta0.3Mn0.4O2 Cathode

Lithium‐rich disordered rock‐salt oxides have attracted great interest owing to their promising performance as Li‐ion battery cathodes. While experimental and theoretical efforts are critical in advancing this class of materials, a fundamental understanding of key property changes upon Li extraction is largely missing. In the present study, single‐crystal synthesis of a new disordered rock‐salt cathode material, Li_1.3Ta_0.3Mn_0.4O₂ (LTMO), and its use as a model compound to investigate Li concentration–driven evolution of local cationic ordering, charge compensation, and chemical distribution are reported. Through the combined use of 2D and 3D X‐ray nanotomography, it is shown that Li removal accompanied by oxygen oxidation is correlated with the development of morphological defects such as particle cracking. Chemical heterogeneity, quantified by subparticle level distribution of Mn valence state, is minimal during Mn redox, which drastically increases upon the formation of cracks during oxygen redox. Density functional theory and bond valence sum mismatch calculations reveal the presence of local short‐range ordering in the pristine oxide, which gradually disappears along with the extraction of Li. The study suggests that with cycling the transformation into true cation–disordered state can be expected, which likely impacts the voltage profile and obtainable energy density of the oxide cathodes.     

负载型Pt-Fe/SiO_2催化剂催化环己烷一步氧化制己二酸

己二酸是合成尼龙-66和尼龙-46纤维的重要原料,并进一步用于生产许多重要的化工产品。工业上的己二酸多采用以硝酸为氧化剂的两步法合成,该工艺不仅工艺复杂,而且对设备有腐蚀作用,还会释放大量的温室气体N_2O。本文以负载型Pt/SiO_2、Fe/SiO_2和Pt-Fe/SiO_2为催化剂,采用过氧化氢和氧气为氧源,研究了环己烷一步氧化制己二酸的绿色合成路线。对催化剂进行ICP、BET比表面积、XRD、TEM等表征,结果表明,Pt-Fe/SiO_2催化剂中不存在与Pt或Fe对应的衍射峰。在最佳反应条件下,用高压釜进行了催化剂性能评价,结果表明,Pt-Fe/SiO_2催化活性略优于Pt/SiO_2和Fe/SiO_2。在环己烷转化率为28%的情况下,己二酸选择性达到33%。     

Tribological and corrosion behaviors of fluorocarbon coating reinforced with sodium iron titanate platelets and whiskers

A series of sodium iron titanate (NFTO)–fluorocarbon composite coatings have been prepared with the liquid-phase blending method. The effects of two types of NFTO, NFTO platelets, and NFTO whiskers, on the tribological and corrosion behaviors of the composite coatings, are systematically studied. The results show that the addition of NFTO can significantly enhance the friction-reducing and wear resistance performances of the fluorocarbon coating. Under dry sliding, the minimum specific wear rate is 1.67 × 10⁻⁴ mm³/Nm for the platelet-filled composite coatings and 1.15 × 10⁻⁴ mm³/Nm for the whisker-filled composite coatings, respectively, showing a decrease of 83.5 and 88.6% than that of pure coating. Under a simulated seawater environment, the minimum specific wear rate is 5.44 × 10⁻⁵ mm³/Nm for the platelet-filled composite coatings and 0.84 × 10⁻⁵ mm³/Nm for the whisker-filled composite coatings, respectively, showing a decrease of 90.5 and 98.5% than that of pure coating. The morphologies of worn surfaces, wear debris, and transfer films are analyzed, and the corresponding wear resistance mechanisms are discussed. The electrochemical impedance spectroscopy certifies a remarkably improved corrosion resistance of the composite coatings which have been immersed in 3.5 wt % NaCl solution for 30 days. The composite coating reinforced with 7.5 wt % platelets shows the highest resistance of 256.3 × 10⁶ Ω·cm², approximately two orders of magnitude higher than that of pure coating. © 2020 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2020 , 137, 48936.