车门铰链系统与车门下沉刚度的相关性

针对某型车门下沉问题,通过台架试验获得车门、铰链和车身等各单因素下沉量和车门绞链系统整体下沉量,对单因素下沉量与系统整体下沉刚度进行线性拟合分析,得到车门铰链系统各单因素与系统下沉刚度的相关度排序.对前、后车门分别选取相关度较高的单因素进行优化,最终改进方案的仿真和试验结果证明该方案可有效地提升车门下沉刚度.采用定量分析法可快速找出影响下沉刚度的敏感因素,并能够快速生成优化方案,为新车型设计提供参考.     

Topology optimization of flexure hinges with a prescribed compliance matrix based on the adaptive spring model and stress constraint

This paper focuses on the configuration design of flexure hinges with a prescribed compliance matrix and preset rotational center position. A new method for the topology optimization of flexure hinges is proposed based on the adaptive spring model and stress constraint. The hinge optimization model is formulated by maximizing the bending displacement with a spring while optimizing the compliance matrix to a prescribed value. To avoid numerical instability, an artificial spring is used as an auxiliary calculation, and a new strategy is developed for adaptively adjusting the spring stiffness according to the prescribed compliance matrix. The maximum stress of flexure hinge is limited by using a normalized P-norm of the effective von Mises stress, and a position constraint of rotational center is proposed to predetermine the position of the rotational center. In addition, to reduce the error of the stress measurement, a simple but effective filtering method is presented to obtain a complete black-and-white design. Numerical examples are used to verify the proposed method. Topology results show that the obtained flexure hinges have the prescribed compliance matrix and preset rotational center position while also meeting the stress requirements.     

多运营商高铁隧道移动网络覆盖方案

高铁移动网络覆盖是国内三大通信运营商的一个重点,而高铁隧道内移动网络覆盖更是运营商的一大难点痛点。文章根据我国中部省份某高铁线路覆盖规划实例,采用“设备+POI+泄漏电缆”模式,即三家运营商信号源设备通过同一POI(point of interface,多系统接入平台)接入,信号输出到泄漏电缆进行隧道覆盖,隧道口场坪站安装宽频切换天线对隧道外进行延伸覆盖,通过链路预算合理布置各运营商主设备信号源,从而实现隧道到室外的无缝覆盖。最后,根据已有成熟网络覆盖解决方案,对未来5G高铁隧道移动网络覆盖方案进行了探讨。     

Topology optimization for crashworthiness of thin-walled structures under axial crash considering nonlinear plastic buckling and locations of plastic hinges

Although topology optimization is established for linear static problems, more effort is required for solving nonlinear plastic problems. A new topology optimization approach with equivalent static loads (ESLs) is suggested to find the optimum topologies and locations of plastic hinges of thin-walled crash boxes by considering crash-induced deformation, the main crash energy-absorbing mechanism. Together with finite element method crashworthiness analyses, considering all nonlinearities with rate-dependent plasticity, the method was developed using an appropriate time-incremental scheme of ESLs without removing any high values of loads. Analyses show that the crash boxes with optimum topologies have energy-absorbing capabilities equivalent to the original structure. The proposed method is evaluated for two crashes: a crash box at low speed and a double cell subjected to high-speed collision. The results indicate that this method captures nonlinear crushing behaviours and accurate locations of plastic hinges where, if proper reinforcements are made, energy absorption can be enhanced.     

重轨矫直速度对矫后残余应力的影响分析

针对矫直速度对重轨矫后残余应力的影响进行研究,利用Pro/E建立60kg·m-1重轨九辊水平矫直模型,采用ANSYS Workbench对重轨矫直过程进行有限元数值模拟,通过现场矫直规程对采用现场矫直速度以及假定矫直速度得到的重轨矫后残余应力进行分析比较,得出了在其余条件不变的情况下重轨的矫直速度在1.4~1.6m·s-1的范围内其轨底矫后纵向残余拉应力小于250MPa,且残余应力分布合理,满足矫直要求,相比于现场采用的1.2m·s-1的矫直速度其生产效率最大能够提高16.7%~33.3%。     

伊朗德黑兰地铁轨道施工方法

依托伊朗德黑兰地铁一、二号线工程 ,针对地铁单洞单线采用的轨道施工轨排法存在的不足 ,根据单洞双线隧道的特点 ,提出了利用组装好的轨排直接铺设在隧道结构底板上作为轨道平板车临时轨道的施工新方法     

液晶显示驱动电路中Fibonacci型电荷泵单元

本文中所设计的电荷泵将用于手机液晶显示驱动模块中.通过对Fibonacci型电荷泵上升时间的估算,对减小上升时间和动态功耗进行折中考虑,本文提出优化开关频率的方法.用1.2μm CMOS双阱工艺参数对所设计的电荷泵进行模拟,结果表明这个电荷泵具有较快的上升速度和较高的效率.通过提高V_GS电平和保证开关管的衬底始终接在最高电位上,文中提出了一种新型Fibonacci电荷泵,它可以正常工作在从1.2V到5V变化的多种电源电压下.     

可持续发展战略指导下的轨道交通规划与评价

提出了轨道交通规划与评价在实施可持续发展战略过程中需要研究的问题，研究重点是轨道交通规划与评价方法体系和环境对策，研究了轨道交通规划目标的变化、轨道交通规划优化决策理论与方法、轨道交通规划中的环境影响评价、城市轨道交通网络的合理规划、城际轨道交通——客运专线/高速铁路线路基本走向的规划、轨道交通规划可持续发展的评价指标体系概念框架、轨道交通系统可持续发展的能力建设问题等，并通过实例验证了所建立的理论方法体系和模型体系；不仅进行了有关理论和方法的探讨，而且以面向实际应用为目标，开发了相应的软件系统，为轨道交     

铝导电轨型材生产工艺研究

研究了6101-T6合金铝导电轨型材的生产工艺，着重研究了化学成分，不同的淬火、时效处理工艺对材料性能的影响。     

铁路桥梁横向振动模拟及适应快速行车结构型式的研究

针对铁路提速后出现的上承式简支钢板梁桥跨中横向振幅过大的问题,以羊楼司桥(L=32m单跨上承式简支钢板梁桥)为例进行实桥检测和数值模拟,建立车辆、线路、桥梁三者的联合模型,考虑轮轨接触力,应用MSC/DYTRAN大型结构分析程序进行车线桥动力相互作用的仿真分析。研究揭示我国用量最多的C62型货车以70∽80km/h的速度空载通过时,该跨度的钢板梁桥发生横向谐振的机理。此外,用该方法对32m跨长的组合梁结构进行桥梁动力特性及列车走行性分析,表明该结构满足提速货车和高速电动旅客列车走行的要求。研究结果对我国高速铁路桥梁建设和既有桥梁的改造具有积极意义。