乙烯、丙烯中微量水含量的分析

采用便携式微量水分析仪和库仑法微量水分析仪测定了乙烯、丙烯试样中的微量水含量,对试样的传输系统、进样量的控制、液体试样的气化和水标准气体的制备方法进行了改进,优化了测试条件。以低吸附惰性管线和小死体积单进单出的不锈钢减压器为试样传输系统,缩短了测试时间。采用液态烃闪蒸气化取样进样器气化液体试样并准确控制试样的进样量,可避免液体试样渐次气化对水含量测定结果的影响及对采样钢瓶大小的限制。采用渗透管发生器制备水标准气体,可验证分析结果的准确度。采用库仑法微量水分析仪测定水含量时,试样流量选择600 m L/min较适宜,开封保存15 d之内的卡尔·费休试剂对测定结果无影响。采用便携式微量水分析仪测定水含量时,选择试样流量在400~800 m L/min之间较适宜。两种仪器的测量结果相近,稳定性好,准确度高,回收率在102%~107%之间,相对偏差小于10%。     

Ca-Mg-Al复合氧化物催化尿素与1,2-丙二醇制碳酸丙烯酯

采用共沉淀法制备了系列Ca-Mg-Al复合氧化物催化剂，通过对沉淀剂配比、沉淀液pH值及焙烧温度等制备条件的考察，得到以Na₂CO₃为沉淀剂、pH=9.5、850℃下焙烧4h制备的Ca-Mg-Al催化活性最高。在 n(PG)∶n(urea)=1.5∶1、反应温度为145℃、绝压20kPa、反应时间4h、催化剂用量为尿素质量的5%时，碳酸丙烯酯收率达到84.6%。采用XRF、XRD、NH₃-TPD、SEM及BET对催化剂的组成、晶型及酸性进行了表征，发现随着沉淀剂中Na₂CO₃的含量增加，催化剂中CaO∶MgO的比例增大，碳酸丙烯酯的收率亦升高；经850℃焙烧后，催化剂中存在CaO和MgO两种活性中心，起协同催化作用；随着焙烧温度由700℃升高到850℃，NH₃-TPD脱附曲线向低温方向偏移，且强酸中心NH₃脱附峰面积比由81.14%明显下降为0，中强酸中心NH₃脱附峰面积比由0增加到78.07%，而碳酸丙烯酯收率由68%增加到84.6%，这表明催化剂强酸性位的减少是催化活性增加的主要原因。     

Fine-tuned,molecular-composite,organosilica membranes for highly efficient propylene/propane separation via suitable pore size

Fine-tuned, molecular-composite, organosilica membranes were fabricated via the co-condensation of organosilica precursors bis(triethoxysilyl)acetylene (BTESA) and bis(triethoxysilyl)benzene (BTESB). Fourier transform infrared and UV–vis spectra confirmed the co-condensation behaviors of BTESA and BTESB. The evolution of the network structure indicated that the incorporated BTESB decreased the membrane pore size, which was determined by a modified gas translation model according to the steric effect of the phenyl groups. The incorporation of BTESB to BTESA finely tuned the membrane structure and endowed the resultant composite membrane with improved separation properties. The BTESAB 9:1 membrane (molar ratio of BTESA/BTESB was 9:1) exhibited high C₃H₆ permeance at 4.5 × 10⁻⁸ mol m⁻² s⁻¹ Pa⁻¹ and a C₃H₆/C₃H₈ permeance ratio of 33 at 50°C. One of the most important developments of this study involved clearly defining the relationship between membrane pore size and C₃H₆/C₃H₈ separation performance for organosilica membranes in single and binary separation systems.     

催化裂解多产丙烯新技术

介绍了国内外利用蜡油或常压渣油等重质原料的增产丙烯技术CPP,ARGG FDFCC和TSRMP;还介绍了利用富含烯烃的混合碳四和催化裂化汽油等轻质原料的增产丙烯技术OCP,Propylur,Superflex,OCT,Meta-4和BASF公司的丁烯歧化工艺技术.     

Performance and Commercial Application of the Promoter LCC-A for Maximization of Propylene Yield

1 Introduction Propylene as an important feedstock for organic chemicals is mainly originated from steam cracking and catalytic cracking processes. During the FCC process the propylene content varies with the FCC catalyst and process technology adopted, resulting in significant difference in propylene concentration in the cracked product——LPG. The conventional FCC pro- cess generally gives a propylene yield of around 4%, while the FCC process with maximization of propylene yield can in…     

Segmented polymer networks containing amino‐dendrimers

Polymer networks in which poly(propylene imine) dendrimers (Astramol?) are connected to each other by linear polytetrahydrofuran (polyTHF) segments, were prepared by two methods. The first method was a one‐step procedure in which bifunctionally living polyTHF, obtained by initiation of the THF polymerization with trifluoromethane sulfonic anhydride (triflic anhydride), was reacted with an amino‐dendrimer. This reaction was very fast but did not allow formation of the end products. The second method was a two‐step procedure. In a first step, living polyTHF, prepared with acryloyloxybutyl triflate as initiator, was grafted on an amino‐dendrimer, to form a star‐like, acrylate‐terminated polyTHF multi‐macromonomer with the dendrimer as core. In a second step, networks were obtained by Michael addition between the acrylate end‐groups and unreacted amino‐groups of the dendrimer. This cross‐linking reaction occurred spontaneously upon heating of the solution of the multi‐macromonomer with gelation times varying from a few minutes to a few hours, depending on the temperature and the composition of the prepolymers. With this method it was possible to prepare networks in the form of coatings or films. © 2003 Society of Chemical Industry     

丙烷脱氢制丙烯经济及技术分析

丙烯是重要的有机化工原料，除用于生产聚丙烯外，还是生产丙烯腈，丁醇、辛醇、环氧丙烷、异丙醇、丙苯、丙烯酸、羧基醇及壬基酚等产品的主要原料，丙烯的齐聚物是提高汽油辛烷值的主要成分，丙烷催化脱氢制丙烯比烃类蒸气裂解能产生更多的丙烯。当用蒸气裂解生产丙烯时，丙烯收率最多只有33％、而用催化脱氢法生产丙烯，总收率可达74％－86％，用唯一原料生产唯一产品，催化脱氢的设备投资比烃类蒸气裂解低33％。并且采用催化脱氢的方法，能有效地得用液化石油气资源使之转变为有用的烯烃。     

Influence of the ethylene–(methacrylic acid)–Zn2+ ionomer on the thermal and mechanical properties of blends of poly(propylene) (PP)/ethylene–(vinyl alcohol) copolymer (EVOH)

The thermal and mechanical properties and the morphologies of blends of poly(propylene) (PP) and an ethylene–(vinyl alcohol) copolymer (EVOH) and of blends of PP/EVOH/ethylene–(methacrylic acid)–Zn²⁺ ionomer were studied to establish the influence of the ionomer addition on the compatibilization of PP/EVOH blends and on their properties. The oxygen transmission rate (O₂TR) values of the blends were measured as well. PP and EVOH are initially incompatible as was determined by tensile tests and scanning electronic microscopy. Addition of the ionomer Zn²⁺ led to good compatibility and mechanical behaviour was improved in all blends. The mechanical properties on extruded films were studied for 90/10 and 80/20 w/w PP/EVOH blends compatibilized with 10 % of ionomer Zn²⁺. These experiments have shown that the tensile properties are better than in the injection‐moulded samples. The stretching during the extrusion improved the compatibility of the blends, diminishing the size of EVOH domains and enhancing their distribution in the PP matrix. As was to be expected, the EVOH improved the oxygen permeation of the films, even in compatibilized blends. Copyright © 2004 Society of Chemical Industry     

Rheological properties of polypropylene modified by high‐intensity ultrasonic waves

A new method using high‐intensity ultrasonic waves, instead of peroxide‐aided reactive extrusion, was applied to modify a linear polypropylene into a branched structure. The ultrasonic waves induced chain scission and created reactive macromolecules of polypropylene successfully in the melt state without any peroxide. To enhance and control the recombination reaction during sonication, a multifunctional agent and an antioxidant were used. The rheological property measurements clearly confirmed that the modified polypropylene had a nonlinear branched structure. It showed shear‐thinning behaviors in its viscosities at low frequencies, high elastic behaviors in Cole–Cole plots, and a high rheological polydispersity index in comparison with a linear polypropylene. The degradation or recombination of polypropylene was adequately controlled by an antioxidant, which stabilized the structure during sonication. Also, the use of an antioxidant was quite effective in improving the extrusion processability by delaying the instability of the extrudate to a higher shear rate. © 2005 Wiley Periodicals, Inc. J Appl Polym Sci, 2006     

助催化剂对TiCl_4/MgCl_2催化丙烯高温聚合的影响

研究了助催化剂种类(三甲基铝、三异丁基铝、三正己基铝、三乙基铝和甲基铝氧烷)及其含量对无内、外给电子体的TiCl4/MgCl2催化剂催化丙烯高温(100℃)聚合性能的影响,并用结晶分级分析、示差扫描量热和凝胶渗透色谱等方法分析了所得聚丙烯的结晶熔融行为和微观结构。实验结果表明,聚合温度从70℃升至100℃时,TiCl4/MgCl2催化剂的定向能力基本不变;100℃聚合时,以烷基化能力较弱的三异丁基铝为助催化剂时TiCl4/MgCl2催化剂的活性最高,而采用烷基化能力最强的三甲基铝为助催化剂时TiCl4/MgCl2催化剂的活性最低;100℃聚合时,助催化剂的种类对TiCl4/MgCl2催化剂的定向能力影响很小。