Demonstration of a tool for automatic learning and re-use of knowledge in the activated sludge process.

Wastewater treatment plant operators encounter complex operational problems related to the activated sludge process and usually respond to these by applying their own intuition and by taking advantage of what they have learnt from past experiences of similar problems. However, previous process experiences are not easy to integrate in numerical control, and new tools must be developed to enable re-use of plant operating experience. The aim of this paper is to investigate the usefulness of a case-based reasoning (CBR) approach to apply learning and re-use of knowledge gained during past incidents to confront actual complex problems through the IWA/COST Benchmark protocol. A case study shows that the proposed CBR system achieves a significant improvement of the benchmark plant performance when facing a high-flow event disturbance.     

Analysis of enterococci using portable testing equipment for developing countries--variance of Azide NutriDisk medium under variable time and temperature.

This report compares the enterococci count on samples obtained with Azide NutriDisk (AND) (sterile, dehydrated culture medium) and Slanetz and Bartley (SB) medium when exposed to a variable in incubation time and temperature. Three experiments were performed to examine the recovery of enterococci on AND and SB media using membrane filtration with respect to: (a) incubation time; (b) incubation temperature; and (c) a combination of the two. Presumptive counts were observed at 37, 41, 46 and 47 degrees C and at 20, 24, 28 and 48 h. These were compared to AWWA standard method 9230 C (44 degrees C, 44 h). Samples were confirmed using Kanamycin Aesculin Azide (KAA) agar. Friedman's ANOVA and Students t-test analysis indicated higher enumeration of enterococci when grown on AND (p = 0.45) than SB (p = < 0.001) at all temperatures with a survival threshold at 47 degrees C. Significant results for AND medium were noted at 20 h (p = 0.021), 24 h (p = 0.278) and 28 h (p = 0.543). The study concluded that the accuracy of the AND medium at a greater time and temperature range provided flexibility in incubator technology making it an appropriate alternative to SB medium for monitoring drinking water using field testing kits in developing countries.     

Enhancing urban infrastructure investment planning practices for a changing climate.

Climate change raises many concerns for urban water management because of the effects on all aspects of the hydrological cycle. Urban water infrastructure has traditionally been designed using historical observations and assuming stationary climatic conditions. The capability of this infrastructure, whether for storm-water drainage, or water supply, may be over- or under-designed for future climatic conditions. In particular, changes in the frequency and intensity of extreme rainfall events will have the most acute effect on storm-water drainage systems. Therefore, it is necessary to take future climatic conditions into consideration in engineering designs in order to enhance water infrastructure investment planning practices in a long time horizon. This paper provides the initial results of a study that is examining ways to enhance urban infrastructure investment planning practices against changes in hydrologic regimes for a changing climate. Design storms and intensity-duration-frequency curves that are used in the engineering design of storm-water drainage systems are developed under future climatic conditions by empirically adjusting the general circulation model output, and using the Gumbel distribution and the Chicago method. Simulations are then performed on an existing storm-water drainage system from NE Calgary to investigate the resiliency of the system under climate change.     

Using decision analysis to determine optimal experimental design for monitoring sewer exfiltration with tracers.

The tracer methods developed to assess exfiltration from sewers in the European project APUSS (assessment of the performance of sewer systems) have a high degree of freedom with regard to the choice of tracer and the dosing strategy. These can lead to very different degrees of uncertainty in the measured exfiltration ratio. In this study, we demonstrate how to select an optimal experimental design using decision analysis, which accounts for this uncertainty and its associated costs. Although the results are site-specific, we can conclude generally that, when NaCl is used as the tracer, the accuracy of the exfiltration estimate is most sensitive to the amount of tracer used and the starting time of the experiment.     

One-dimensional GIS-based model compared with a two-dimensional model in urban floods simulation.

A GIS-based one-dimensional flood simulation model is presented and applied to the centre of the city of N?mes (Gard, France), for mapping flow depths or velocities in the streets network. The geometry of the one-dimensional elements is derived from the Digital Elevation Model (DEM). The flow is routed from one element to the next using the kinematic wave approximation. At the crossroads, the flows in the downstream branches are computed using a conceptual scheme. This scheme was previously designed to fit Y-shaped pipes junctions, and has been modified here to fit X-shaped crossroads. The results were compared with the results of a two-dimensional hydrodynamic model based on the full shallow water equations. The comparison shows that good agreements can be found in the steepest streets of the study zone, but differences may be important in the other streets. Some reasons that can explain the differences between the two models are given and some research possibilities are proposed.     

Identification of the adverse effect of nitrate on the phosphate release rate and improvement of EBPR process models.

The adverse effect of nitrate on the phosphate release rate in the anaerobic phase was observed and was hardly explainable with conventional EBPR process models. Four possible mechanisms were proposed including substrate competition, reduced fermentation, parallel reaction and sequential reaction. Batch experiments were designed and conducted to identify the dominant mechanism. Results showed that the sequential reaction was the only possible mechanism where only denitrification occurred if any nitrate existed in the anaerobic phase. Then the phosphate release following after the nitrate was completely removed. Nitrate inhibition effect was added into the PHA storage rate to incorporate the sequential reaction in the conventional ASM3 plus EAWAG bio-P module (ASM3 + P). Nitrate inhibition coefficient, K(I,NO,PAO) was found to be as low as 0.05 mg/L. This correlated well with experimental observation where no also meant that the anaerobic compartment of a continuous flow reactor could be seriously affected by the residual nitrate contained in the sludge recycle flow. This phenomenon caused overestimation of the phosphate uptake rate and consequently underestimation of PO4(3-) -P concentration. This problem was resolved by incorporation of a nitrate inhibition term in the ASM3 + P for more accurate simulation of the EBPR process.     

Design of a retention tank: comparison of stormwater quality models with various levels of complexity.

Stormwater quality simulation models are useful tools for the design and management of sewer systems. Modelling results are highly sensitive to experimental data used for calibration. This sensitivity is examined for three modelling approaches of various complexities (site mean concentration approach, event mean concentration approach and build-up, washoff and transport modelling approach) applied to a typical case study (design of a dry detention tank), accounting for the variability of calibration data and their effect on simulation results. Calibrated models with different calibration data sets were used to simulate 3 years of rainfall with different retention tank specific volumes. Annual pollutant load interception efficiencies were determined. Simulations results revealed (i) that there is no advantage in using the EMC model compared to the SMC model and (ii) that the BWT model resulted in higher design ratios than those given by the SMC/hydraulic approach. For both EMC and BWT models, using an increasing number n of events for calibration leads to narrower confidence intervals for the design ratios. It is crucial for design ratios to account for successive storm events in chronological order and to account for the maximum allowable flow to be transferred to the downstream WWTP.     

Inhibition of microbial growth in ready‐to‐eat food stored at ambient temperature by modified atmosphere packaging

This study was undertaken to develop a modified atmosphere package to control microbial growth in ready‐to‐eat (RTE) products stored at ambient temperature. Ethanol and/or limonene associated with modified atmosphere (CO₂ : O₂ : N₂ = 30% : 5% : 65%) was used to inhibit the growth of total air‐borne microorganisms and Escherichia coli in RTE products stored at 25°C. The results indicated that 0.05% ethanol vapour in the headspace was effective to inhibit the growth of air‐borne microorganisms and E. coli at 25°C for 72 h in a model study, and the effectiveness was related to ethanol content. Both 73 ppm limonene and 0.05% ethanol vapour enhanced the bacteriostatic effect of modified atmosphere in RTE sushi roll products, and no off‐flavour was detected using this formulated gas; however, no significant inhibitory effect was observed for RTE cold noodle products. This study concludes that combinations of carbon dioxide, ethanol or limonene vapours are effective to inhibit microbial growth in RTE food at ambient temperature, and the outcome may be due to the hurdle effect. Copyright © 2003 John Wiley & Sons, Ltd.     

State of polarization changes: Classification and measurement

We propose a standardization procedure that provides a convenient, quantitative and reproducible laboratory-based method for measuring the state of polarization (SOP) fluctuations produced by polarization varying devices. This method is based on the SOP distributions generated by commercial polarization scramblers. We show that these devices generate distributions of the maximum change of the SOP (in a given sample time) that follow Rayleigh statistics, which scale linearly with scrambling frequency and the sample time. We use this procedure to measure the SOP fluctuations in a short length of coiled fiber subject to mechanical perturbations.     

Oligo(ethylene oxide) side‐chain steric screening effects on conductimetric properties of grafted poly(4‐vinylpyridinium) salts in aqueous solutions

A set of poly[N‐oligo(ethylene oxide)yl 4‐vinylpyridinium tosylate] (P4VOEOOTs) has been prepared by spontaneous polymerization of 4‐vinylpyridine. This method gives a grafted polyelectrolyte having a positive charge on every backbone pyridinic moiety. The P4VP15Ts, P4VP164Ts, P4VP350Ts and P4VP750Ts aqueous solution conductivities were determined in the concentration range from 6 × 10^?4 to 10^?2 M at 25 °C. The variation of the conductivity versus concentration of the investigated system exhibits typical polyelectrolyte behaviour. The polyelectrolyte mobility was found to be dependent on the oligo(ethylene oxide) (OEO) side‐chain length. Manning's rod‐like model fails to describe these results. A simple steric effect is proposed to explain the influence of the OEO length. Copyright © 2003 Society of Chemical Industry