High-performance supercapacitor of manganese oxide/reduced graphene oxide nanocomposite coated on flexible carbon fiber paper

Although supercapacitors have higher power density than batteries, they are still limited by low energy density and low capacity retention. Here we report a high-performance supercapacitor electrode of manganese oxide/reduced graphene oxide nanocomposite coated on flexible carbon fiber paper (MnO₂–rGO/CFP). MnO₂–rGO nanocomposite was produced using a colloidal mixing of rGO nanosheets and 1.8 ± 0.2 nm MnO₂ nanoparticles. MnO₂–rGO nanocomposite was coated on CFP using a spray-coating technique. MnO₂–rGO/CFP exhibited ultrahigh specific capacitance and stability. The specific capacitance of MnO₂–rGO/CFP determined by a galvanostatic charge–discharge method at 0.1 A g⁻¹ is about 393 F g⁻¹, which is 1.6-, 2.2-, 2.5-, and 7.4-fold higher than those of MnO₂–GO/CFP, MnO₂/CFP, rGO/CFP, and GO/CFP, respectively. The capacity retention of MnO₂–rGO/CFP is over 98.5% of the original capacitance after 2000 cycles. This electrode has comparatively 6%, 11%, 13%, and 18% higher stability than MnO₂–GO/CFP, MnO₂/CFP, rGO/CFP, and GO/CFP, respectively. It is believed that the ultrahigh performance of MnO₂–rGO/CFP is possibly due to high conductivity of rGO, high active surface area of tiny MnO₂, and high porosity between each MnO₂–rGO nanosheet coated on porous CFP. An as-fabricated all-solid-state prototype MnO₂–rGO/CFP supercapacitor (2 × 14 cm) can spin up a 3 V motor for about 6 min.     

Hierarchically Fe-doped porous carbon derived from phenolic resin for high performance supercapacitor

Supercapacitors are promising for high power application in the recent years. In particular, the conversion of simple and available carbon materials into economic and high performance electrical devices receives excellent scientific and technological interest. This paper reports a one-step strategy for synthesizing hierarchical porous carbon derived from phenolic resin (PR), which is then used to configure electric double-layer capacitors (EDLCs). Here, a carbon material with a flexible porous structure, large specific surface area, and high graphitization degree is prepared using potassium ferrate (K₂FeO₄) to catalytically activate PR and to realize synchronous carbonization and graphitization. This method overcomes the disadvantage of time-consuming, high-cost, and environmentally unfriendly. In addition, the as-prepared carbon material has a high specific surface area (1086 m² g^?1) and a large pore size (3.07 nm), which can increase the transfer rate of electrolyte ions. The specific capacitance of the obtained electrode material is 315 F g^?1 at 1.0 A g^?1, and the optimized electrode material has an ultra-long cycle lifetime (capacitance retention rate is 96.3% after 10,000 cycles). Thus, the hierarchically Fe-doped porous carbon material derived from PR material is expected to realize high rate capacitance for supercapacitor applications.     

The additive-free electrode based on the layered MnO2 nanoflowers/reduced,graphene oxide film for high performance supercapacitor

The MnO₂ nanoflowers/reduced graphene oxide composite is coated on a nickel foam substrate (denoted as MnO₂ NF/RGO @ Ni foam) via the layer by layer (LBL) self-assembly technology without any polymer additive, following the soft chemical reduction. The layered MnO₂ NF/RGO composite is uniformly anchored on the Ni foam skeleton to form the 3D porous framework, and the interlayers have access to lots of ions channels to improve the electron transfer and diffusion. This special construction of 3D porous structure is beneficial to the enhancement of electrochemical property. The specific capacitance is up to 246 F g⁻¹ under the current density of 0.5 A g⁻¹. After 1000 cycles, it can retain about 93%, exhibiting excellent cycle stability. The electrochemical impedance spectroscopy measurements confirm that MnO₂ NF/RGO @ Ni foam electrode has lower R_ESR and R_CT values when compared to MnO₂ @ Ni foam and RGO @ Ni foam. This study opens a new door to the preparation of composite electrodes for high performance supercapacitor.     

Manganese oxide embedded polypyrrole nanocomposites for electrochemical supercapacitor

MnO₂ embedded PPy nanocomposite (MnO₂/PPy) thin film electrodes were electrochemically synthesized over polished graphite susbtrates. Growing PPy polymer chains provides large surface area template that enables MnO₂ to form as nanoparticles embeded within polymer matrix. Co-deposition of MnO₂ and PPy has a complimentary action in which porous PPy matrix provides high active surface area for the MnO₂ nanoparticles and, on the other hand, MnO₂ nanoparticles nucleated over polymer chains contribute to enhanced conductivity and stability of the nanocomposite material by interlinking the PPy polymer chains. The MnO₂/PPy nanocomposite thin film electrodes show significant improvement in the redox performance as cyclic voltammetric studies have shown. Specific capacitance of the nanocomposite is remarkably high (∼620 F g⁻¹) in comparision to its constituents MnO₂ (∼225 F g⁻¹) and PPy (∼250 F g⁻¹). Photoelectron spectroscopy studies show that hydrated manganese oxide in the nanocomposite exists in the mixed Mn(II) to Mn(IV) oxidation states. Accordingly, chemical structures of MnO₂ and PPy constituents in the nanocomposite are not influenced by the co-deposition process. The MnO₂/PPy nanocomposite electrode material however shows significantly improved high specific capacitity, charge-discharge stability and the redox performance properties suitable for application in the high energy density supercapcitors.     

Fabrication of a fibrous MnO2@MXene/CNT electrode for high-performance flexible supercapacitor

As shining stars of 2-dimensional materials, transition metal carbides (MXene) and transition metal oxides have attracted much interest in various energy fields due to their excellent conductive and electrochemical properties. However, big challenge still remains in the accessibility of high-performance fibrous electrodes for flexible supercapacitors. In this paper, MnO₂ nanorods are loaded on MXene sheets to obtain MnO₂@MXene composites by a facile hydrothermal method, which are subsequently coated on carbon nanotube fibers (CNTFs). With a fine control on morphology, the resulting MnO₂@MXene/CNTF electrode exhibits a high specific capacitance of 181.8 F/g at 1 A/g, a capacitance retention of 91% after 5000 charge-discharge cycles, as well as superb flexibility, i.e., neglected capacitance loss at a bending angle of 180°. The as-fabricated flexible composite fiber opens a new door for transition metal carbides and transition metal oxides with great potential in flexible electronics.     

Multiwall carbon nanotube supported poly(3,4-ethylenedioxythiophene)/manganese oxide nano-composite electrode for super-capacitors

MWCNT-PSS/PEDOT/MnO₂ nano-composite electrodes were fabricated by generating pseudo-capacitive poly(3,4-ethylenedioxythiophene) (PEDOT)/MnO₂ nano-structures on poly(styrene sulfonate) (PSS) dispersed multiwalled carbon nanotubes (MWCNTs). PSS dispersed MWCNTs (MWCNT-PSS) facilitated the growth of PEDOT and MnO₂ into nano-rods with large active surface area and good electrical conductivity. The ternary MWCNT-PSS/PEDOT/MnO₂ nano-composite electrode was studied for the application in super-capacitors, and exhibited excellent capacitive behavior between −0.2 V and 0.8 V (vs. saturated Ag/AgCl electrode) with high reversibility. Specific capacitance of the nano-composite electrode was found as high as 375 F g⁻¹. In contrast, specific capacitance of MWCNT-PSS/MnO₂ and MWCNT-PSS nano-composite electrodes is 175 F g⁻¹ and 15 F g⁻¹, respectively. Based on cyclic voltammetric studies and cycle-life tests, the MWCNT-PSS/PEDOT/MnO₂ nano-composite electrode gave a highly stable and reversible performance up to 2000 cycles. Our studies demonstrate that the synergistic combination of MWCNT-PSS, PEDOT and MnO₂ has advantages over the sum of the individual components.     

Flexible electrodes based on polypyrrole/manganese dioxide/polypropylene fibrous membrane composite for supercapacitor

The composites of polypyrrole/manganese dioxide/polypropylene fibrous films (PPy/MnO₂/PPF) have been prepared in situ through chemical oxidation polymerization by using the mixture of FeCl₃·6H₂O and MnO₂ adsorbed on PPF as oxidant in the atmosphere of pyrrole vapor at room temperature. The morphologies and structures of the composites are investigated by using scanning electron microscope and X-ray diffraction spectroscopy. The properties of the capacitor cells assembled by the composites of PPy/MnO₂/PPF are evaluated by cyclic voltammetry, galvanostatic charge/discharge and electrochemical impedance spectroscopy methods. The results reveal that the morphologies, conductivities and capacitance performance of the composites are influenced strongly by the content of MnO₂ in the solution of oxidant. The capacitors assembled by PPy/MnO₂/PPF exhibit the property of quick charge/discharge, and the highest specific capacitance of about 110 F g⁻¹ is obtained when the PPy/MnO₂ content in the composite is about 17.4%.     

Hierarchical MnO2@NiCo2O4@Ti3SiC2/carbon cloth core-shell structure with superior electrochemical performance for all solid-state supercapacitors

Core-shell hierarchical structured composites have demonstrated great advantages in numerous energy storage devices. In particular, structured composites with rationally structural components and controllable morphology are the most effective in enhancing electrochemical properties. In this work, MnO₂@NiCo₂O₄@Ti₃SiC₂/CC (carbon cloth) core-shell hierarchical structured composites were designed and successfully synthesized via electrospinning followed by a two-step hydrothermal reaction. The Ti₃SiC₂/CC nanofibers and core-shell nanoarrays were able to improve the specific capacitance and cycling stability. In the three-electrode system, the specific capacitance of MnO₂@NiCo₂O₄@Ti₃SiC₂/CC was observed as 1938.2 F/g at a current density of 1 A/g, while the rate capability retention was observed as 81.7% between 1 and 10 A/g. Furthermore, a superior cycling stability was observed following 5000 cycles with a specific capacitance retention rate of 55.4%. Employing MnO₂@NiCo₂O₄@Ti₃SiC₂/CC as the all solid-state supercapacitor positive electrode exhibited a high energy density of 58.0 W h/kg at the power density of 800 W/kg. Results demonstrate the potential of the MnO₂@NiCo₂O₄@Ti₃SiC₂/CC as an electrode material with phenomenal electrochemical properties for supercapacitors.     

Fabrication of PANI@Ti3C2Tx/PVA hydrogel composite as flexible supercapacitor electrode with good electrochemical performance

Developing a new strategy to effectively prevent the restacking of MXene nanosheets will have significant impacts on designing flexible supercapacitor electrodes. Herein, a novel Ti₃C₂T_x/polyvinyl alcohol (PVA) porous sponge with 3D interconnected structures is prepared by sol-gel and freeze-dried methods. This Ti₃C₂T_x/PVA porous sponge is used as the template of in-situ polyaniline (PANI) polymerization, and the fabricated PANI@Ti₃C₂T_x/PVA hydrogel composite is applied as flexible supercapacitors electrodes. 1D conductive polymer chains PVA could increase the interlayer spacing of Ti₃C₂T_x nanosheets, which is beneficial to expose more electrochemical active sites. The supercapacitor based on PANI@Ti₃C₂T_x/PVA hydrogel composite exhibits the coexistence of double-layer capacitance and pseudocapacitance behavior. This supercapacitor shows a maximum areal specific capacitance of 103.8 mF cm^?2 at 2 A m^?2, and it also exhibits a maximum energy density of 9.2 μWh·cm^?2 and an optimum power density of 800 μW cm^?2. The capacitance of this supercapacitor is almost not change under different bending angles. Moreover, 99% capacitance retention is achieved after 10 000 charge/discharge cycles of the supercapacitor. The synergistic effect between PANI and Ti₃C₂T_x/PVA composite may improve the number of reactive sites and provide efficient channels for ion diffusion/electron transport.     

Coaxial carbon nanofibers/MnO2 nanocomposites as freestanding electrodes for high-performance electrochemical capacitors

Carbon nanofibers (CNFs)/MnO₂ nanocomposites were prepared as freestanding electrodes using in situ redox deposition and electrospinning. The electrospun CNFs substrates with porosity and interconnectivity enabled the uniform incorporation of birnessite-type MnO₂ deposits on each fiber, thus showing unique and conformal coaxial nanostructure. CNFs not only provided considerable specific surface area for high mass loading of MnO₂ but also offered reliable electrical conductivity to ensure the full utilization of MnO₂ coatings. The effect of MnO₂ loading on the electrochemical performances was investigated by cyclic voltammetry (CV), impedance measurements and Galvonostatic charging/discharging technique. The results showed that an ultrathin MnO₂ deposits were indispensable to achieve better electrochemical performance. The maximum specific capacitance (based on pristine MnO₂) attained to 557 F/g at a current density of 1 A/g in 0.1 M Na₂SO₄ electrolyte when the mass loading reached 0.33 mg/cm². This freestanding electrode also exhibited good rate capability (power density of 13.5 kW/kg and energy density of 20.9 Wh/kg at 30 A/g) and long-term cycling stability (retaining 94% of its initial capacitance after 1500 cycles). These characteristics suggested that such freestanding CNFs/MnO₂ nanocomposites are promising for high-performance supercapacitors.     

Electrochemical fabrication of polyaniline/MnO2/graphite felt as free‐standing,flexible electrode for supercapacitors

Polyaniline/MnO₂/graphite felt (PMGF) composite, which can be used as a novel free‐standing, flexible electrode for supercapacitors, was fabricated via a facile electrochemical method. Polyaniline/graphite felt (PANI/GF) electrode was prepared by electropolymerization of PANI onto the GF. Subsequently, manganese dioxide (MnO₂) was electrodeposited on the surface of the PANI/GF electrode to prepare PMGF electrode. The microstructure and morphology of the as‐prepared samples were characterized by Fourier transform infrared spectra, X‐ray diffraction, scanning electron microscopy, and transmission electron microscopy. Specific surface area was examined using N₂ adsorption/desorption test. Cyclic voltammogram, chronopotentiometry techniques and electrochemical impedance spectroscopy were introduced to investigate the electrochemical performance of the composites. The PMGF electrode exhibited specific capacitance as high as about 630 F g⁻¹ at the current density of 0.5 A g⁻¹, which is much higher than that of PANI/MnO₂ composites reported previously. The high specific capacitance of PMGF may be attributed to the fact that the porous GF is a good conductive matrix for the dispersion of PANI/MnO₂ and it can facilitate easy access of electrolytes to the electrode, which results in enhancement of the electrochemical performance of the composite. Moreover, the specific capacitance of PMGF is much larger than that of MnO₂/GF (MGF), which may be ascribed to the participant of PANI, which contributes additional pseudocapacitance and electron transport path. POLYM. COMPOS., 34:819–824, 2013. © 2013 Society of Plastics Engineers     

A novel method to prepare nanostructured manganese dioxide and its electrochemical properties as a supercapacitor electrode

Nanostructured MnO₂ was synthesized by co-precipitation in the presence of Pluronic P123 surfactant and characterized by X-ray diffraction (XRD), infrared spectroscopy (IR), scanning electron microscope (SEM) and transmission electron microscope (TEM). The sample without surfactant was spherical with particle size on the submicron scale, whereas P123-assisted samples were all loose clew shapes, consisting of MnO₂ nanowires, 8-20 nm in diameter and 200-400 nm in length. The electrochemical performances of the as-prepared MnO₂ as the electrode materials for supercapacitors were evaluated by cyclic voltammetry and galvanostatic charge-discharge measurements in a solution of 1 M Na₂SO₄. The sample without surfactant exhibited a relatively low specific capacitance of 77 F g⁻¹, whereas the nanostructured MnO₂ prepared with 0.02% (wt%) P123 exhibited excellent pseudocapacitive behavior, with a maximum specific capacitance of 176 F g⁻¹.     

Fabrication of manganese oxide/three-dimensional reduced graphene oxide composites as the supercapacitors by a reverse microemulsion method

Manganese oxide (MnO₂)/three-dimensional (3D) reduced graphene oxide (RGO) composites were prepared by a reverse microemulsion (water/oil) method. MnO₂ nanoparticles (3–20 nm in diameter) with different morphologies were produced and dispersed homogeneously on the macropore surfaces of the 3D RGO. Scanning electron microscopy and transmission electron microscopy were applied to characterize the microstructure of the composites. The MnO₂/3D RGO composites, which were annealed at 150 °C, displayed a significantly high specific capacitance of 709.8 F g⁻¹ at 0.2 A g⁻¹. After 1000 cycles, the capacitance retention was measured to be 97.6%, which indicates an excellent long-term stability of the MnO₂/3D RGO composites.     

Electrophoretic deposition of MnO2-coated carbon nanotubes on a graphite sheet as a flexible electrode for supercapacitors

A flexible electrode was prepared by microwave heating deposition of manganese oxide (MnO₂) on carbon nanotubes (CNTs) followed by electrophoretic deposition of the MnO₂-coated CNTs on a flexible graphite sheet (FGS). The prepared MnO₂-coated CNTs were characterized by scanning and transmission electron microscopy, and X-ray diffraction. A uniformly thin nano-scale MnO₂ coating was formed on the surface of the CNTs. The MnO₂-coated CNTs–FGS electrode showed highly capacitive behaviour in the 0.5 M Na₂SO₄ aqueous solution, with a specific capacitance of 442.9 F/g based on MnO₂ at 2 mV/s. It exhibited an excellent cycling stability with no more than 1.1% capacitance loss after 1000 cycles at 50 mV/s.     

Enhanced electrochemical stability and charge storage of MnO2/carbon nanotubes composite modified by polyaniline coating layer in acidic electrolytes

Manganese dioxide/multiwalled carbon nanotubes (MnO₂/MWCNTs) were synthesized by chemically depositing MnO₂ onto the surface of MWCNTs wrapped with poly(sodium-p-styrenesulfonate). Then, polyaniline (PANI) with good supercapacitive performance was further coated onto the MnO₂/MWCNTs composite to form PANI/MnO₂/MWCNTs organic-inorganic hybrid nanoarchitecture. Electrochemical performance of the hybrid in Na₂SO₄-H₂SO₄ mixed acidic electrolytes was evaluated by cyclic voltammetry (CV) and chronopotentiometry (CP) in detail. Comparative electrochemical tests revealed that the hybrid nanoarchitecture could operate in the acidic medium due to the protective modification of PANI coating layer onto the MnO₂/MWCNTs composite, and that its electrochemical behavior was greatly dependent upon the concentration of protons in the acidic electrolytes. Here, PANI not only served as a physical barrier to restrain the underlying MnO₂/MWCNTs composite from reductive-dissolution process so as to make the novel ternary hybrid material work in acidic medium to enhance the utilization of manganese oxide as much as possible, but also was another electroactive material for energy storage in the acidic mixed electrolytes. It was due to the existence of PNAI layer that an even larger specific capacitance (SC) of 384 F g⁻¹ and a much better SC retention of 79.9% over 1000 continuous charge/discharge cycles than those for the MnO₂/MWCNTs nanocomposite were delivered for the hybrid in the optimum 0.5 M Na₂SO₄-0.5 M H₂SO₄ mixed acidic electrolyte.     

Electrolytes for hybrid carbon-MnO2 electrochemical capacitors

Different aqueous-based electrolytes have been tested in order to improve the electrochemical performance of hybrid (asymmetric) carbon/MnO₂ electrochemical capacitor (EC). Chloride and bromide aqueous solutions lead to the formation of Cl₂ and Br₂ respectively upon oxidation of the corresponding salt, thus limiting the useful electrochemical window of the MnO₂ electrode and producing gas evolution (in the case of chloride salts) detrimental to the cycling ability of an hybrid device. For sulfate and nitrate salts, MnO₂ electrode exhibits a 20% increase in capacitance when lithium is used as the cation compared to sodium or potassium salts, probably due to partial lithium intercalation in the tunnels of α-MnO₂ structure. The higher ionic conductivity and solubility of LiNO₃ has led to the investigation of this electrolyte in carbon/MnO₂ supercapacitor compared to standard hybrid cell using K₂SO₄. A lower resistance increase was evidenced when the temperature was decreased down to −10 °C. Long term cycling ability of carbon/MnO₂ supercapacitor was also evidenced with 5 M LiNO₃ electrolyte.     

Hydrothermal synthesis of MnO<Subscript>2</Subscript>/CNT nanocomposite with a CNT core/porous MnO<Subscript>2</Subscript> sheath hierarchy architecture for supercapacitors

MnO₂/carbon nanotube [CNT] nanocomposites with a CNT core/porous MnO₂ sheath hierarchy architecture are synthesized by a simple hydrothermal treatment. X-ray diffraction and Raman spectroscopy analyses reveal that birnessite-type MnO₂ is produced through the hydrothermal synthesis. Morphological characterization reveals that three-dimensional hierarchy architecture is built with a highly porous layer consisting of interconnected MnO₂ nanoflakes uniformly coated on the CNT surface. The nanocomposite with a composition of 72 wt.% (K_0.2MnO₂·0.33 H₂O)/28 wt.% CNT has a large specific surface area of 237.8 m²/g. Electrochemical properties of the CNT, the pure MnO₂, and the MnO₂/CNT nanocomposite electrodes are investigated by cyclic voltammetry and electrochemical impedance spectroscopy measurements. The MnO₂/CNT nanocomposite electrode exhibits much larger specific capacitance compared with both the CNT electrode and the pure MnO₂ electrode and significantly improves rate capability compared to the pure MnO₂ electrode. The superior supercapacitive performance of the MnO₂/CNT nancomposite electrode is due to its high specific surface area and unique hierarchy architecture which facilitate fast electron and ion transport.     

Thermoelectric properties of Ca0.8Dy0.2MnO3 synthesized by solution combustion process

High-quality Ca_0.8Dy_0.2MnO₃ nano-powders were synthesized by the solution combustion process. The size of the synthesized Ca_0.8Dy_0.2MnO₃ powders was approximately 23 nm. The green pellets were sintered at 1150-1300°C at a step size of 50°C. Sintered Ca_0.8Dy_0.2MnO₃ bodies crystallized in the perovskite structure with an orthorhombic symmetry. The sintering temperature did not affect the Seebeck coefficient, but significantly affected the electrical conductivity. The electrical conductivity of Ca_0.8Dy_0.2MnO₃ increased with increasing temperature, indicating a semiconducting behavior. The absolute value of the Seebeck coefficient gradually increased with an increase in temperature. The highest power factor (3.7 × 10^-5 Wm^-1 K^-2 at 800°C) was obtained for Ca_0.8Dy_0.2MnO₃ sintered at 1,250°C. In this study, we investigated the microstructure and thermoelectric properties of Ca_0.8Dy_0.2MnO₃, depending on sintering temperature.     

Barnacle-like manganese oxide decorated porous carbon nanofibers for high-performance asymmetric supercapacitors

In this study, barnacle-like manganese oxide (MnO₂) decorated porous carbon nanofibers (PCNF) were synthesized using electrospinning and the chemical precipitation method for high-performance asymmetric supercapacitors. The porous structure of PCNF was acquired using poly(styrene-co-acrylonitrile) in the electrospinning solution. In order to obtain the optimized barnacle-like MnO₂ on PCNF (MnO₂-PCNF), the barnacle-like MnO₂ was synthesized using different synthetic times (namely, 1.5, 3.0, and 7.0 min) of the chemical precipitation. Among them, the optimized MnO₂-PCNF for 3.0 min exhibited the well-dispersed MnO₂ on the PCNF with the nano-size of 190–218 nm. The optimized MnO₂-PCNF showed the superior specific capacitance of 209.8 F g^?1 at 10 mV s^?1 and the excellent high-rate performance of 160.3 F g^?1 at 200 mV s^?1 with the capacitance retention of 98.7% at 100 mV s^?1 for 300 cycles. In addition, electrochemical performances of asymmetric cell (constructed activated carbon and MnO₂-PCNF) showed the high specific capacitance of 60.6 F g^?1 at the current density of 0.5 A g^?1, high-rate capacitance of 30.0 F g^?1 at the current density of 10 A g^?1, and the excellent energy density of 30.3–15.0 Wh kg^?1 in the power density range from 270 to 9000 W kg^?1. The enhanced electrochemical performance can be explained by the synergistic effects of barnacle-like MnO₂ nanoparticles with a high active area related to high specific capacitance and well-dispersed MnO₂ with a short ion diffusion length related to the excellent high-rate performance.     

Effect of MnO2 addition on properties of NiFe2O4-based cermets

The impact of MnO₂ as an additive on the properties of NiFe₂O₄-based cermets prepared by the two-steps sintering method has been investigated. The new material was characterized in terms of the crystal structure, microstructure, linear shrinkage, relative density and porosity. Moreover, the bending strength of NiFe₂O₄-based cermets was measured. Differential scanning calorimetry (DSC) and X-ray diffraction analysis (XRD) shows that the addition of MnO₂ has no obvious influence on the crystal structure of the cermets. Scanning electron microscope (SEM) studies reveals that the grain sizes of cermets decreases slightly with doped MnO₂. The results show that the linear shrinkage, relative density and bending strength increase at first and then decrease slightly. A high-density (99.56%) and high-strength (84.28 MPa) NiFe₂O₄-based cermets has been obtained by adding 0.50 wt% MnO₂ into the matrix.