接收机参数对北斗三号卫星伪距偏差影响研究

伪距偏差是抑制北斗系统服务能力提升的重要误差源,影响用户实时定位性能和卫星精密定轨处理.目前对北斗三号伪距偏差的分析研究与测量较少,文章首先从理论上分析了接收机的前端滤波带宽和相关器间隔对伪距偏差的影响,并对理论分析结果进行了仿真.然后在此基础上利用7.5 m大口径天线对北斗三号在轨卫星信号进行采集,使用软件接收机对卫星实测数据的伪距偏差进行测试验证,全面分析了前端滤波带宽和相关器间隔对北斗三号卫星信号伪距偏差的影响.根据理论分析和实测验证的结果,得到了接收机的相关器间隔和前端滤波带宽对北斗三号卫星B1I、B3I和B1C信号的伪距偏差影响范围.研究表明,通过合理设置接收机相关器间隔和前端滤波带宽,可有效减小北斗三号卫星信号伪距偏差,提升用户定位精度.     

北斗B1C频点正交复用二进制偏移载波信号闸波设计方法

第3代北斗卫星导航系统中B1C频点信号将使用正交复用二进制偏移载波调制方式。为了增强北斗卫星导航接收机码跟踪环路的抗多径性能并且解决码跟踪中的模糊跟踪问题,该文针对正交复用二进制偏移载波调制信号QMBOC(6, 1, 4/33)提出一种双闸波码跟踪环路结构。根据理想的目标鉴相函数和二进制偏移载波调制信号自相关函数的特点分别设计出针对BOC(1, 1)和BOC(6, 1)信号的闸波,并在本地码跟踪环路中使用这两种不同的闸波分别与输入信号相关,最后将所得的两个相关函数进行加权合并以用于鉴相过程。计算机仿真结果表明所提方法不仅能够有效消除QMBOC(6, 1, 4/33)信号的模糊跟踪可能性,且能够大幅增强接收机的抗多径性能,其对应多径误差包络面积相比于现有的方法能够减少约33%。     

一种矢量跟踪环路及其抗干扰性能分析

针对GPS信号在接收端的功率较弱,接收机在载噪比低的环境中很容易受到其他信号的干扰,该文提出一种基于矢量跟踪环路的接收机设计方法,在跟踪环路环节对干扰信号进行抑制。以实际的伪距、伪距率误差为状态量,量测得到的伪距、伪距率误差为观测量构建跟踪环路滤波器,利用更新后的接收机位置,计算出接收机与可视卫星间的观测矢量,完成闭合反馈回路。接收机的信号跟踪与导航解算部分融合一体,改变了传统接收机的结构。对比分析标量和矢量跟踪环路的预测伪距方差,来研究矢量跟踪环路对干扰信号的抑制性能。采用实际卫星星历进行仿真实验,验证了矢量跟踪环路比标量跟踪环路的预测伪距方差小,抗干扰能力强。     

矢量跟踪算法快速重跟性能分析

当卫星导航信号受到一段时间干扰或遮蔽时,信号载噪比下降,传统跟踪环路失锁。信号恢复时,针对传统跟踪环路不能及时重新跟踪问题,应用矢量跟踪算法,进行跟踪。分析了在真实GPS数据加上仿真噪声之后矢量/频率锁定环路（VDFLL）的性能以及与传统环路进行对比,试验证明矢量跟踪具有快速重跟性能。     

基于盲判决反馈均衡的GPS信号多径干扰抑制方法

给出了存在多径效应时的GPS接收信号模型,分析了多径干扰对GPS接收机跟踪环路的影响,将均衡技术应用于跟踪环路,提出了一种GPS信号多径干扰抑制方法.该方法在GPS信号跟踪环路中引入了判决反馈分数间隔均衡器,同时,根据GPS信号为BPSK调制且发送的伪码序列被导航电文调制后存在正负反转不确定性的特点,均衡器系数更新时选...     

伪码测距雷达中的伪码跟踪环路设计

提出了一种适用于伪码测距雷达的伪码跟踪环设计方法,重点对伪码跟踪环的跟踪精度和动态性能进行了分析,讨论了一种最小跟踪误差意义下的最优环路带宽确定方法。仿真结果表明伪码跟踪环跟踪精度高,对动态运动的适应能力强。     

利用多相关器的伪码测距多址干扰抑制算法性能分析

伪码跟踪多相关器技术广泛应用于导航接收机抗多径和导航信号质量监测。论文通过对比分析多径和多址信号对导航信号相关峰畸变的影响,揭示了多相关器技术可用于多址干扰抑制。通过仿真分析了多址误差随期望接收信号与干扰信号功率差和载波多普勒频率差的变化规律,并与传统的并行多址干扰对消方法进行了对比。仿真结果表明当多址干扰信号功率差小于10dB时,ELS和Double-delta与单级并行干扰对消方法的性能相当,但是实现复杂度大大降低。      

现代OS导航信号中HRC相关间隔的优化设计

目前接收机基于环路的多径抑制主要采用窄相关和HRC技术,而在实际应用中HRC技术对不同调制方式的现代导航信号采取的相关间隔也不同。针对上述问题,通过对几种现代导航信号的鉴相范围和多径抑制性能进行分析,给出在现代导航信号中HRC鉴别器算法相关间隔的优化设计方法。仿真可见:不同现代导航信号下HRC相关间隔的优化选取也不同;带宽较宽时,鉴相范围随相关间隔增大而增大,多径抑制性能随相关间隔减小而提高;带宽较窄和相关间隔较小时,在一定鉴相范围内减小相关间隔并不会再提高现代导航信号的多径抑制性能。提出的相关间隔的优化方法具有创新性,研究成果具有重要理论价值并已应用到GNSS接收机中。     

动态环境下载波锁相跟踪环的信号级仿真

在接收信号载噪比一定的前提下,针对GPS软件接收机在不同运动状态下载波环跟踪的问题,仿真研究了不同环路的跟踪性能:在低加速度动态下采用2阶锁相环跟踪更佳,在高加速度动态下则应该采用3阶锁相环跟踪。通过仿真验证了环路的有效性。此外通过仿真发现当载噪比和滤波器噪声带宽一定的情况下,选择合适的预检测积分时间可以有利于载波跟踪。     

BOC调制导航信号关键技术研究

BOC调制作为一种导航信号体制,具有良好的抗多径和抗干扰性能,同时实现共用载波频率条件下的频谱分离。与BPSK调制信号相比,BOC调制信号具有多径误差小、码跟踪热噪声误差小的优点。通过对BOC调制技术和合路方式的深入分析,给出了各种BOC调制的自相关和功率谱函数,以及各种合路方式的分析比较。通过仿真验证了BOC信号的码跟踪性能和抗多径性能的优越性。     

Resolution Enhancement Technology:Integrated Process Solutions using OPC

DUV lithography, using the 248 nm wavelength, is a viable manufacturing option for devices with features at 130 nm and less. Given the low kl value of the lithography, integrated process development is a necessary method for achieving acceptable process latitude. The application of assist features for rule based OPC requires the simultaneous optimization of the mask, illumination optics and the resist.Described in this paper are the details involved in optimizing each of these aspects for line and space imaging.A reference pitch is first chosen to determine how the optics will be set. The ideal sigma setting is determined by a simple geometrically derived expression. The inner and outer machine settings are determined, in turn,with the simulation of a figure of merit. The maximum value of the response surface of this FOM occurs at the optimal sigma settings. Experimental confirmation of this is shown in the paper.Assist features are used to modify the aerial image of the more isolated images on the mask. The effect that the diffraction of the scattering bars (SBs) has on the image intensity distribution is explained. Rules for determining the size and placement of SBs are also given.Resist is optimized for use with off-axis illumination and assist features. A general explanation of the material' s effect is discussed along with the affect on the through-pitch bias. The paper culminates with the showing of the lithographic results from the fully optimized system.     

Cost-effective test solutions for smart card and other integrated flash applications

From its emergence in the late 1980s as a lower cost alternative to early EEPROM technologies, flash memory has evolved to higher densities and speedsand rapidly growing acceptance in mobile applications.In the process, flash memory devices have placed increased test requirements on manufacturers. Today, as flash device test grows in importance in China, manufacturers face growing pressure for reduced cost-oftest, increased throughput and greater return on investment for test equipment. At the same time, the move to integrated flash packages for contactless smart card applications adds a significant further challenge to manufacturers seeking rapid, low-cost test.     

An improved parallel thinning algorithm with two subiterations

The parallel thinning algorithm with two subiterations is improved in this paper. By analyzing the notions of connected components and passes, a conclusion is drawn that the number of passes and the number of eight-connected components are equal. Then the expression of the number of eight-connected components is obtained which replaces the old one in the algorithm. And a reserving condition is proposed by experiments, which alleviates the excess deletion where a diagonal line and a beeline intersect. The experimental results demonstrate that the thinned curve is almost located in the middle of the original curve connectivelv with single pixel width and the processing speed is high.     

Theoretical analysis of the relationship between the Brillouin gain coefficient and the strain in the optical-fiber sensors

The relation between the power of the Brillouin signal and the strain is one of the bases of the distributed fiber sensors of temperature and strain. The coefficient of the Bfillouin gain can be changed by the temperature and the strain that will affect the power of the Brillouin scattering. The relation between the change of the Brillouin gain coefficient and the strain is thought to be linear by many researchers. However, it is not always linear based on the theoretical analysis and numerical simulation. Therefore, errors will be caused if the relation between the change of the Brillouin gain coefficient and the strain is regarded as to be linear approximately for measuring the temperature and the strain. For this reason, the influence of the parameters on the Brillouin gain coefficient is proposed through theoretical analysis and numerical simulation.     

Novel fiber-optical interferometer with miniaturized probe for in-hole measurements

Today, micro-system technology and the development of new MEMS （Micro-Electro-Mechanical Systems） are emerging rapidly. In order for this development to become a success in the long run, measurement systems have to ensure product quality. Most often, MEMS have to be tested by means of functionality or destructive tests. One reason for this is that there are no suitable systems or sensing probes available which can be used for the measurement of quasi inaccessible features like small holes or cavities. We present a measurement system that could be used for these kinds of measurements. The system combines a fiber optical, miniaturized sensing probe with low-coherence interferometry, so that absolute distance measurements with nanometer accuracy are possible.     

Study of waveguide coupling efficiency in hybrid silicon lasers

This paper presents a new method to increase the waveguide coupling efficiency in hybrid silicon lasers. We find that the propagation constant of the InGaAsP emitting layer can be equal to that of the Si resonant layer through improving the design size of the InP waveguide. The coupling power achieves 42% of the total power in the hybrid lasers when the thickness of the bonding layer is 100 nm. Our result is very close to 50% of the total power reported by Intel when the thickness of the thin bonding layer is less than 5 nm. Therefore, our invariable coupling power technique is simpler than Intel＇s.     

Curved crystal spectrometer for the measurement of X-ray lines from laser-produced plasmas

In order to diagnose the laser-produced plasmas, a focusing curved crystal spectrometer has been developed for measuring the X-ray lines radiated from a laser-produced plasmas. The design is based on the fact that the ray emitted from a source located at one focus of an ellipse will converge on the other focus by the reflection of the elliptical surface. The focal length and the eccentricity of the ellipse are 1350 mm and 0.9586, respectively. The spectrometer can be used to measure the X- ray lines in the wavelength range of 0.2-0.37 nm, and a LiF crystal （200） （2d = 0.4027 nm） is used as dispersive element covering Bragg angle from 30° to 67.5°. The spectrometer was tested on Shengnang- Ⅱ which can deliver laser energy of 60-80 J/pulse and the laser wavelength is 0.35 μm. Photographs of spectra including the 1 s2p ^1P1-1s^2 ^1S0 resonance line（w）, the 1s2p ^3P2-1s^2 1S0 magnetic quadrupole line（x）, the 1s2p ^3P1-1 s^2 ^1S0 intercombination lines（y）, the 1 s2p ^3S~1-1 s^2 ^1S0 forbidden line（z） in helium-like Ti Ⅹ Ⅺ and the 1 s2s2p ^2P3/2-1 s622s ^2S1/2 line（q） in lithium-like Ti Ⅹ Ⅹhave been recorded with a X-ray CCD camera. The experimental result shows that the wavelength resolution（λ/△ 2） is above 1000 and the elliptical crystal spectrometer is suitable for X-ray spectroscopy.     

Preparation and Characterization of TaN ALD Precursors

High purity organic-tantalum precursors for thin film ALD TaN were synthesized and characterized.Vapor pressure and thermal stability of these precursors were studied.From the vapor pressure analysis,it was found that TBTEMT has a higher vapor pressure than any other published liquid TaN precursor,including TBTDET,TAITMATA,and IPTDET.Thermal stability of the alkyl groups on the precursors was investigated using a 1H NMR technique.The results indicated that the tertbutylimino group is the most stable group on TBTDET and TBTEMT as compared to the dialkylamido groups.Thermal stability of TaN precursors decreased in the following order:TBTDET ＞ PDMAT ＞ TBTEMT.In conclusion,precursor vapor pressure and thermal stability were tuned by making slight variations in the ligand sphere around the metal center.     

Electronic Structure of Semiconductor Nanocrystals

This paper reviews our recent development of the use of the large-scale pseudopotential method to calculate the electronic structure of semiconductor nanocrystals, such as quantum dots and wires, which often contain tens of thousands of atoms. The calculated size-dependent exciton energies and absorption spectra of quantum dots and wires are in good agreement with experiments. We show that the electronic structure of a nanocrystal can be tuned not only by its size,but also by its shape. Finally,we show that defect properties in quantum dots can be significantly different from those in bulk semiconductors.     

A rigorous proof of MIMO channel capacity’s increase with antenna number

It is well known that adding more antennas at the transmitter or at the receiver may offer larger channel capacity in the multiple-input multiple-output（MIMO） communication systems. In this letter, a simple proof is presented for the fact that the channel capacity increases with an increase in the number of receiving antennas. The proof is based on the famous capacity formula of Foschini and Gans with matrix theory.