稀土元素Sm对Mg-Zn-Y合金组织结构和力学性能的影响

制备了Mg-6Zn-1.5Y-0.8Zr-xSm(x=0,1,2,3)系列合金,研究了稀土元素Sm对Mg-6Zn-1.5Y-0.8Zr合金组织结构和力学性能的影响.通过金相显微镜、扫描电镜、EDS、XRD等观察和分析了合金的微观形貌和组织结构,测量了合金抗拉强度、屈服强度和伸长率等力学性能.结果表明:合金中添加稀土元素Sm后晶粒有了明显的细化,随着Sm元素含量的增加,晶粒细化效果更为明显;通过XRD分析,添加Sm元素后,合金中并没有出现新的含Sm的物相,通过扫描电镜和EDS分析表明,合金中加入的Sm置换了部分Y,形成了Mg3( SmY)2 Zn3,Mg3( SmY) Zn6的相结构,Sm元素对Y的置换主要出现在Mg3( SmY) Zn6结构当中,在Mg3 (SmY) Zn6相结构出现较少;力学性能测试结果表明,随着Sm含量增多,合金晶粒细化,细晶强化作用明显,合金屈服强度逐渐增大,而抗拉强度和伸长率在Sm含量为2％时达到最大,比未添加Sm元素时提高约15％以上.     

Al-4.9Zn-1.6Mg-0.4Mn-0.1Zr-xEr合金时效行为研究

采用金相(OM)、透射电镜(TEM)及能谱分析(EDS)、硬度测试的方法研究了单级与双级时效热处理制度对Al-4.9Zn-1.6Mg-0.4Mn-0.1Zr-xEr合金板材硬度和显微组织的影响.结果表明,添加Er元素后合金中形成了纳米级的A13(Zr,Er)相,可以强烈地钉扎位错,细化再结晶晶粒.无论单级时效还是双级时效,Er元素的添加均可以提高合金的硬度,加快合金的时效硬化速率,使合金达到硬度峰值的时间缩短,但Er含量对提高合金硬度的影响不大.同时,晶界处出现的第二相颗粒析出带得到消除,合金中存在明显的沉淀无析出带.此外,Er元素可以促进Zn,Mg元素的固溶,而析出的A13(Zr,Er)颗粒又可以促进MgZn2相的析出.     

Microstructure and mechanical properties of Mg-Zn-Y-Nd-Zr alloys

The microstructure and tensile properties of the as-cast and solution treatment Mg-4.5Zn-1Y-xNd-0.5Zr (x=0, 1 wt.%, 2 wt.%, 3 wt.%) alloys were investigated. The results showed that the microstructure of Mg-4.5Zn-1Y-0.5Zr alloy consisted of α-Mg, Zn-Zr, W (Mg₃Y₂Zn₃) and I (Mg₃YZn₆) phases. With the addition of Nd, I-phase disappeared and Mg₃Y₂Zn₃ phase changed into Mg₃(Nd,Y)₂Zn₃ phase. When the content of Nd reached 3 wt.%, T phase, i.e., ternary Mg-Zn-Nd phase, formed. In addition, with the increase of Nd content in the alloys, the secondary dendritic arm spacing decreased, while the amount of intermetallic phases increased. For as-cast Mg-4.5Zn-1Y-xNd-0.5Zr alloys, after solution treatment, microsegregation was eliminated and the shape of eutectic structure of α-Mg+W transformed from lamellar into spherical. The tensile strength and elongation of Mg-4.5Zn-1Y- 3Nd-0.5Zr alloy were increased from 219.2 MPa and 11.0% to 247.5 MPa and 20.0%, respectively.     

Deformation Behavior of Ultra-Strong and Ductile Mg-Gd-Y-Zn-Zr Alloy with Bimodal Microstructure

Metallurgical and Materials Transactions A - An ultra-strong and ductile Mg-8.2Gd-3.8Y-1Zn-0.4Zr (wt pct) alloy was developed by using hot extrusion to modify the microstructure via...     

Texture Evolution in Mg-Zn-Ca Alloy Sheets

Ca was added to Mg-1Zn and Mg-6Zn alloys to modify their texture, and the origin of texture modification by Ca addition has been investigated. It shows that Mg-1Zn-1Ca (ZX11) and Mg-6Zn-1Ca (ZX61) alloy sheets in the as-rolled condition show the textures having a splitting of basal poles toward the rolling direction and a splitting of basal poles toward the transverse direction, respectively. An analysis of the microstructure in the as-rolled condition shows that two different types of twins become active during rolling, double twins for ZX11 and tension twins for ZX61, suggesting that double twinning and tension twinning promote a splitting of basal poles toward the rolling direction (ZX11) and transverse direction (ZX61), respectively. On the other hand, after annealing, both alloy sheets show a weakened texture characterized by a splitting of basal poles toward the transverse direction. During annealing, the growth of tension twin-oriented grains occurs, resulting in the texture having a splitting of basal poles toward the transverse direction in both alloys. These alloys show not only higher yield strength but also better stretch formability than Al 5052 alloy, showing their potential as highly formable Mg sheet alloys.     

Microstructure and mechanical properties of Mg-xY-1.5MM-0.4Zr alloys

Age hardening,microstructure and mechanical properties of Mg-xY-1.5MM-0.4Zr (x=0,2,4,6 wt.%) alloys (MM represents Ce-based misch-metal) were investigated by scanning electron microscopy (SEM) and transmission electron microscopy (TEM). The results showed that the formed precipitates being responsible for age hardening changed from fine hexagonal-shaped equilibrium Mg12MM phase to metastable β’ phase with bco crystal structure when Y was added into Mg-1.5MM-0.4Zr alloy,and the volume fraction of precipitate phases also increased. With the increase of Y content in Mg-Y-1.5MM-0.4Zr alloys,it was found that the age hardening was enhanced,the grain sizes became finer and the tensile strength was improved. The cubic-shaped β-Mg24Y5 precipitate phases were observed at grain boundaries in Mg-6Y-1.5MM-0.4Zr alloy. It was suggested that the distribution of prismatic shaped β’ phases and cubic shaped β-Mg24Y5 precipitate phases in Mg matrix might account for the remarkable enhancement of tensile strength of Mg-Y-MM-Zr alloy. It was shown that the Mg-6Y-1.5MM-0.4Zr alloy was with maximum tensile strength at aged-peak hardness,UTS of 280 MPa at room temperature and 223 MPa at 250 oC,respectively.     

Effects of Alloying Elements on Creep Properties of Mg-Gd-Zr Alloys

The minimum creep rate and microstructures of aged samples of Mg-Gd-Zr alloys, with and without alloying additions of Zn and/or Y, have been investigated in the present work. The creep tests were performed at 523 K (250 °C) and under 80 to 120 MPa, and the microstructures before and after creep tests were characterized using scanning electron microscopy, transmission electron microscopy, and the high-angle annular dark-field imaging technique. It is found that dislocation creep predominates in the steady-state creep stage for all alloys. The Mg-2.5Gd-0.1Zr (at. pct) alloy, strengthened by the β′ precipitates, has minimum creep rates in the range 1.0 × 10^?8 to 3.8 × 10^?8 s^?1 under 80 to 120 MPa. The addition of 1.0 at. pct Zn to the Mg-2.5Gd-0.1Zr alloy reduces the 0.2 pct proof strength and increases the minimum creep rate, resulting from the formation of γ′ basal plates at the expense of β′ precipitates. The replacement of 1.0 at. pct Gd by Y in the Mg-2.5Gd-1.0Zn-0.1Zr alloy leads to a substantial reduction in the minimum creep rate, even though it does not cause much change to the 0.2 pct proof strength. The reduced minimum creep rate is attributed to a much lower diffusivity of Y atoms than Gd in the solid magnesium matrix. An increase in the Gd content from Mg-1.5Gd-1.0Y-1.0Zn-0.1Zr to Mg-2.5Gd-1.0Y-1.0Zn-0.1Zr leads to a denser distribution of precipitates, a higher 0.2 pct proof strength, and a further reduction in the minimum creep rate.     

Role of Alloying Elements in the Mechanical Behaviors of An Mg-Zn-Zr-Er Alloy

The mechanical behavior of the as-extruded and heat-treated Mg-1.5Zn-0.6Zr and Mg-1.5Zn-0.6Zr-2Er alloys was investigated and correlated with microstructure evolution. Deformation mechanisms are detailed. No evidence of twinning was observed under compression in the Er-bearing alloy throughout the grain size range of ~5 to 27 μm at a strain rate of 0.001 or 1/s. The compressive yield strength followed a Hall–Petch relation with a slope of ~10.3 MPa/mm^1/2. Er played a major role in the pyramidal 〈c+a〉 slip that was identified as a dominant plastic deformation mechanism. The CRSS for 〈c+a〉 slip system was greatly reduced and was 98 MPa in the as-extruded alloy. While it did not change the mechanical response of the Mg-1.5Zn-0.6Zr-2Er alloy, annealing was found to promote dissolution of Zn in the Mg matrix, leading to an increase in CRSS for extension twinning in the heat-treated Mg-1.5Zn-0.6Zr alloy. As a result, twinning was only observed under a higher strain rate of 1/s in compression. The CRSS for extension twinning for the heat-treated alloy with a grain size of ~28 μm was estimated to be 40 MPa, a bit lower than that for the Er-bearing alloy of the same grain size, which was 42 MPa.     

Mg-12Gd-3Y-0.6Zr合金的二次挤压热变形行为

采用Gleeble-1500型热模拟机在变形温度为360~480℃、应变速率为0.01~10 s-1、真应变为0~0.7的条件下,研究Mg-12Gd-3Y-0.6Zr合金二次挤压过程的热变形行为,获得其热变形工艺参数,并分析热变形后的显微组织。结果表明:合金的峰值应力随应变速率的增大而提高,随应变温度的升高而降低;在变形温度、应变速率相同的情况下,一次热模拟的峰值应力均大于二次热模拟(450℃,10 s~(-1)除外);合金二次挤压过程的流变应力可以采用含Zener-Hollomon参数的双曲正弦函数形式来描述;由于二次热模拟试样中位错及晶界运动增强,使二次热模拟的激活能(Q)、应力指数(n)均小于一次热模拟的相应参数,导致二次挤压较一次挤压容易发生再结晶。     

Preparation,microstructure and properties of Al-Zn-Mg-Sc alloy tubes

The Al-6.0Zn-2.0Mg-0.2Sc-0.10Zr hollow tube ingots, prepared by semi-continuous casting technology, were subjected to ho- mogenization treatment, hot extrusion, intermediate annealing, tension, solution and aging treatment. The microstructures and properties of as-cast Al-Zn-Mg-Sc alloy at different homogenization treatment conditions were studied using hardness measurement, X-ray diffraction (XRD), scanning electron microscopy (SEM) and transmission electron microscopy (TEM) analysis. The results showed th...     

Nd对Mg-11Li-3Al-2Zn-0.2Zr合金组织、力学性能及腐蚀行为的影响

研究稀土Nd对均匀化态Mg-11Li-3Al-2Zn-0.2Zr合金组织、力学性能及腐蚀行为的影响.通过真空感应熔炼制备镁锂合金铸锭, 经均匀化处理(280 ℃, 24 h)得到均匀化态Mg-11Li-3Al-2Zn-xNd-0.2Zr(x=0, 0.5, 1.0, 1.5)合金.采用XRD和SEM分析合金的显微组织, 并对合金进行拉伸试验和断口分析.采用电化学法和析氢失重法研究合金在3.5 %NaCl溶液中的腐蚀行为.结果表明:Mg-11Li-3Al-2Zn-0.2Zr合金主要含有β-Li、AlLi、MgLi₂Al相, Nd的加入使合金中形成NdAl3相.随着Nd含量的增加, 合金的强度和塑性呈先增大后降低的趋势. Mg-11Li-3Al-2Zn-1Nd-0.2Zr合金表现出较优的力学性能, 其抗拉强度和延伸率相对于Mg-11Li-3Al-2Zn-0.2Zr合金分别提高了28.8 %和51.3 %.稀土Nd的添加使合金的耐蚀性能提高.      

Influence of Nd and Y additions on the corrosion behaviour of extruded Mg-Zn-Zr alloys

To improve the corrosion resistance of wrought magnesium alloys through rare earth (RE) additions, the corrosion behaviour of Mg-5Zn-0.3Zr-xNd (x=0, 1, and 2; wt%) and Mg-5Zn-0.3Zr-2Nd-yY (y=0.5 and 1; wt%) alloys in a 5wt% NaCl solution was investigated using immersion test and electrochemical measurements. The results of immersion test show that Mg-5Zn-0.3Zr-2Nd alloy exhibits the best corrosion resistance among the tested alloys. Electrochemical measurements show that secondary phases in RE-containing Mg-5Zn-0.3Zr alloys behave as less noble cathodes in micro-galvanic corrosion and suppress the cathodic process. The additions of Nd and Y into Mg-5Zn-0.3Zr alloy also improve the compactness of the corrosion product film and are beneficial to the corrosion resistance.     

Microstructures and Properties of Al-Zn-Mg-Cu-Zr Alloys with Minor Scandium

The microstructures of Al-Zn-Mg-Cu-Zr al- loys with minor Sc were studied by using optical microscope（OM）, scanning electron microscope （SEM） and transmission electron microscope（TEM）. The tensile mechanical properties and electric conductivity of the studied alloys under different treatment conditions were tested. The results show that adding minor Sc can greatly fines the grain size of the Al-Zn-Mg-Cu-Zr alloy ingots and obviously improves the tensile properties and electric conductivity of the alloys. The strengthening mechanism is considered as fine grain strengthening, sub-structure strengthening and dispersion strengthening by Al3 （Sc, Zr）.     

Microstructure and High Temperature Impression Creep Properties of Mg–3Ca–xZr (x = 0.3, 0.6, 0.9 wt%) Alloys

The current study has investigated the influence of zirconium (Zr) addition to Mg–3Ca–xZr (x = 0.3, 0.6, 0.9 wt%) alloys prepared using argon arc melting on the microstructure and impression properties at 448–498 K under constant stress of 380 MPa. Microstructural analysis of as-cast Mg–3Ca–xZr alloys showed grain refinement with Zr addition. The observed grain refinement was attributed to the growth restriction effect of Zr in hypoperitectic Mg–3Ca–0.3 wt% Zr alloys. Heterogeneous nucleation of α-Mg in properitectic Zr during solidification resulted in grain refinement of hyperperitectic Mg–3Ca–0.6 wt% Zr and Mg–3Ca–0.9 wt% Zr alloys. The hardness of Mg–3Ca–xZr alloys increased as the amount of Zr increased due to grain refinement and solid solution strengthening of α-Mg by Zr. Creep resistance of Mg–3Ca–xZr alloys increased with the addition of Zr due to solid solution strengthening of α-Mg by Zr. The calculated activation energy (Q_a) for Mg–3Ca samples (131.49 kJ/mol) was the highest among all alloy compositions. The Q_a values for 0.3, 0.6 and 0.9 wt% Zr containing Mg–3Ca alloys were 107.22, 118.18 and 115.24 kJ/mol, respectively.     

The intergranular microstructure of cast Mg-Zn and Mg-Zn-rare earth alloys

The solidification path and microstructure of cast Mg-9Zn and Mg-8Zn-1.5MM (misch metal) alloys have been investigated by a combination of thermal analysis and analytical electron microscopy. The addition of 1.5 wt pct MM had a strong influence on the as-cast microstructure with the introduction of new “ternary” interdendritic phases and structural modification of known binary phases. The temperature ranges for formation of these phases from the melt were identified, their crystal structures determined, and their compositions analyzed. Products from eutectoidal decomposition of the interdendritic phase in the binary Mg-9Zn alloy were also identified.     

固溶时效处理对Al-6.6Zn-2.3Mg-2.1Cu-0.12Zr合金组织性能的影响

采用光学显微镜、扫描电镜、透射电镜、X射线衍射、硬度测试、电导率测试和室温拉伸性能测试等分析手段,研究了Al-6.6Zn-2.3Mg-2.1Cu-0.12Zr合金挤压板带固溶、单级时效和双级时效制度下的组织和性能。研究表明,Al-6.6Zn-2.3Mg-2.1Cu-0.12Zr合金挤压板带采用475℃/2 h的固溶处理制度,析出相回溶充分,无过烧现象;合金采用475℃/2 h+120℃/24 h的T6时效处理制度,晶内析出相细小弥散,晶界析出相连续分布;合金采用475℃/2 h+110℃/8 h+160℃/28 h的T74双级固溶时效处理制度,晶内析出相以η’和η为主,晶界析出物完全断开。     

Microstructure and mechanical properties of Mg-Gd-Y-Sm-Al alloy and analysis of grain refinement and strengthening mechanism

The effects of Sm on the microstructure and mechanical properties of Mg-11 Gd-2 Y-0.6 Al alloy were investigated by X-ray diffraction,optical microscopy,scanning electron microscopy,energy dispersive spectrometry and high resolution transmission electron microscopy.Based on the theory of edge—edge matching and electronegativity theory,the mechanism of grain refinement is discussed.The strengthening mechanism is expounded conveniently from fine grain strengthening,coherent strengthening,precipitation strengthening and grain boundary strengthening.The results show that the micro structure of Mg-11 Gd-2 Y-0.6 Al alloy is mainly composed of a-Mg matrix,Mg_5 Gd and Mg_(24)Y_5 phases.The addition of Sm forms Mg_(41)Sm_5 phase in the alloy and refines the alloy.The addition of Sm significantly improves the mechanical properties of the alloy at room and high temperatures.When the addition of Sm is 3 wt%,the tensile strengths of the alloy at room temperature and high temperature(200℃) reach the maximum value 292 and 321 MPa,respectively.The fracture mode of the alloy at different temperatures is mainly brittle fracture and intercrystalline fracture.     

Effects of substitution of Nd in a sand-cast Mg-2.5Nd-0.6Zn-0.5Zr alloy with x wt.% Sm(x=2.5, 4, and 6)

The microstructures and mechanical properties of a series of sand-cast Mg-Sm-Zn-Zr alloys under ascast, solution-treated and peak-aged states were thoroughly investigated. The OM, XRD, SEM and HRTEM were employed to characterize the microstructural evolution. The results indicate that substitution Nd in the conventional Mg-2.5 Nd-0.6 Zn-0.5 Zr alloy with different contents of Sm has comparative grain refinement effect and will fully change the dominant intermetallic phase. In addition, the substituted alloys perform clearly higher strength with comparative ductility at both as-cast and peakaged conditions and much greater aging hardening response than the referential alloy. It is obvious that the strength increments of this alloy are attributed to the changes of the eutectic intermetallic particles on grain boundaries.     

Effect of Ca and Y additions on oxidation behavior of magnesium alloys at high temperatures

Oxidation and ignition of magnesium alloys at elevated temperature were successfully retarded by additions of Y and Ca,which could be melted at 1173 K in air without any protection.Thermogravimetric measurements in dry air revealed that the oxidation dynamics curves of Mg-2.5Ca alloy and Mg-3.5Y-0.79Ca alloy at high temperatures followed the parabolic-line law or the cubic-line law.X-ray diffraction(XRD) and scanning electron microscopy(SEM) analysis indicated that the oxide film on the surface of Mg-3.5Y-0.79Ca and Mg-2.5Ca alloys exhibited a duplex structure,which agreed with the results of thermodynamic analysis.By comparison,the ignition-proof effect of the combination addition of Y and Ca was better than that of the single addition of Ca.     

Effect of phosphorus modification on the microstructure and mechanical properties of DC cast Al-17.5Si-4.5Cu-1Zn-0.7Mg-0.5Ni alloy

Direct chill (DC) casting of an Al-17.5Si-4.5Cu-1Zn-0.7Mg-0.5Ni alloy with minor additions of Zr, V and Ti was performed and the effect of phosphorus modification on the solidification microstructure and mechanical properties were investigated. The results show that the addition of phosphorus refines the primary Si crystals remarkably but coarsens the eutectic Si in the DC cast billets. In the samples taken in 1/2 radius region of the billets of 100 mm in diameter, the average size of the primary Si particles in the unmodified alloy is 38 μm, while that in the modified alloys range from 13 to 26 μm, depending on the melt treatment time. The AlP particles as heterogeneous nucleation sites for the primary Si crystals were observed in the center of the primary Si particles. In the modified alloy, the achieved ultimate tensile strength is 320MPa and 433MPa respectively in the as-cast state and T6 state. The size of the primary Si particles is critical for the improvement of the mechanical properties of the alloy.