共查询到20条相似文献,搜索用时 453 毫秒
1.
2.
3.
4.
5.
采用不同的锻压工艺对货车上心盘进行了锻压,并对其试样进行了冲击性能和耐腐蚀性能的测试与分析。结果表明:在试验条件下,随始锻温度从1140℃升高至1300℃、终锻温度从720℃升高至880℃,锻压速度从100 mm/min增大至400 mm/min,货车上心盘的冲击性能和耐腐蚀性能均先提高后下降。货车上心盘的最佳锻压工艺参数为:始锻温度1260℃、终锻温度800℃、锻压速度300 mm/min。 相似文献
6.
机油滤清器端部法兰等组成构件的成形质量对其使用寿命和工作可靠性起着重要作用。为了预测控制法兰零件冲压成形工艺,本文采用有限元数值模拟方法研究机油滤清器端部法兰多道次冲压成形工艺。基于Deform-3D软件环境建立了机油滤清器法兰零件多道次冲压成形过程的有限元模型,实现包括拉深、材料断裂、翻边等成形过程的数值模拟。通过零件几何形状的比较验证了所建立的有限元模型对法兰零件冲压成形过程的模拟是可靠的。运用该模型对法兰多道次冲压成形过程进行了数值模拟,分析了成形过程的载荷变化、模具和坯料接触情况、零件几何形状演化等,结果表明所制定的成形工艺能够成形合格零件。 相似文献
7.
8.
9.
以某型号万向联轴器法兰叉头为研究对象,针对铸造工艺引起的内部组织疏松,造成零件质量不稳定的问题,提出采用闭式模锻工艺的生产方式。采用Deform-3D对闭式模锻过程进行了仿真,观察了成形时金属的填充过程以及成形力的变化过程,并分析了不同坯料高径比及锻压速度对法兰叉头成形质量及成形力大小的影响。模拟结果表明:采用闭式模锻工艺,能够获得填充饱满的法兰叉头锻件;当坯料高径比为0.96、锻压速度为15 mm·s-1时,获得的锻件质量更好,所需的成形力也更小。最后,基于模拟结果,设计了锻造模具,进行了锻造试验,对闭式模锻工艺的合理性进行了验证。 相似文献
10.
以车用法兰螺母冷挤压成形为研究对象,根据其结构特点设计6工位成形工艺,选取其中易出现缺陷的六角成形工序,采用有限元分析软件DEFOMR-3D对其成形过程进行模拟分析,采用双顶杆结构替代原有单顶杆结构,成功解决成形过程中的材料折叠问题。同时,为降低成形载荷,选取凹模圆角半径、模芯切入角、凸模切入角、摩擦系数作为因素,设计正交试验对参数进行优选,得出各因素对成形载荷的影响趋势,确定最优工艺参数为:凹模圆角半径为0.5 mm、模芯切入角为20°、凸模切入角为10°、摩擦系数为0.12,采用优化后的模具结构及参数进行试模,制件符合成形要求,成形载荷与模拟结果基本一致,为法兰螺母生产提供理论基础。 相似文献
11.
12.
13.
扫描电镜观察显示胫骨是一种由羟基磷灰石和胶原蛋白组成的自然生物陶瓷复合材料.羟基磷灰石具有层状的微结构并且平行于骨的表面排列.观察也显示这些羟基磷灰石层又是由许多羟基磷灰石片所组成,这些羟基磷灰石片具有长而薄的形状,也以平行的方式整齐排列.基于在胫骨中观察到的羟基磷灰石片的微结构特征,通过微结构模型分析及实验,研究了羟基磷灰石片平行排列微结构的最大拔出能.结果表明,羟基磷灰石片长而薄的形状以及平行排列方式增加了其最大拔出能,进而提高了骨的断裂韧性. 相似文献
14.
15.
论述了CAD技术中参数化设计的三种建模方法,重点介绍了基于特征的参数化建模原理。在此基础上,分析机械设计中的机构结构,归纳出其零件的几何特征构成。设计了机构CAD图形库,并提出了该图形库生成步骤和人机交互界面。 相似文献
16.
采用激光辐照对FeCrAlW电弧喷涂层的组织进行致密化处理,借助扫描电镜和X衍射对涂层的组织进行了分析.测试了涂层的显微硬度.结果表明:涂层组织致密度提高,孔隙率明显降低.随着激光扫描速度的增加,涂层的显微硬度降低.在较低的扫描速度下,涂层与基体之间形成互熔区,涂层与基体之间产生良好的冶金结合. 相似文献
17.
18.
19.
C. Colinet 《Intermetallics》2003,11(11-12):1095
A large number of ab-initio calculations of energies of formation of intermetallic compounds have been performed in the last 15 years. The currently used methods are listed. The paper presents a review of the aluminium based compounds which have been studied. Comparisons of calculated and experimental enthalpies of formation are provided for aluminim-3d and-4d transition metal alloys at equiatomic composition. The modelling of the enthalpies of mixing of solid solutions based on a given lattice is described. 相似文献
20.
O. N. Vlasova N. N. Korneeva V. I. Eremenko O. Kh. Fatkullin N. M. Semenova S. N. Petrova D. D. Vaulin 《Metal Science and Heat Treatment》1991,33(12):924-931
Conclusions To provide a high level of mechanical properties in wrought blanks of cast ÉP741NP and ÉP962 alloys it is necessary to form controlled structures. A necklace-type structure formed in homogenizing isostatic treatment, subsequent thermomechanical working including alternation of the operations of deformation in the (+)-area and recrystallization anneals, and final heat treatment is preferable. The temperature conditions of all stages of thermomechanical working are strictly controlled, especially the final operation of deformation and heating for hardening. To eliminate hardening cracks and distortions it is necessary to use molten salts at t=600°C as quenchants. The use of multiple production operations makes it possible to significantly reduce the structural inhomogeneity related to inhertance of the original dendritic structure. However, the structure of the final semifinished product is nevertheless characterized by a difference in occurrence of the processes of polygonization and recrystallization between the former dendritic cells and the interdendritic spaces in deformation and heat treatment.To obtain structurally homogeneous blanks for gas turbine engine parts it is necessary to use basically new methods of remelting such as vacuum double electrode remelting and electron beam remelting with an intermediate vessel.Translated from Metallovedenie i Termicheskaya Obrabotka Metallov, No. 12, pp. 25–29, December, 1991. 相似文献