共查询到20条相似文献,搜索用时 500 毫秒
1.
2.
提出了一种基于深刻蚀脊形光波导带模斑转换器的多功能2×2 GaAs/GaAlAs多模干涉型光开关,并用变量变换级数展开法及三维有限差分束传播法对其进行了模拟分析与优化设计.结果表明,通过控制多模波导中央的两段Schottky电极,器件可实现交叉态、直通态及3dB耦合器功能,并有较大的制作容差、较宽的工作带宽,只须一个多模波导,器件结构紧凑.采用深刻蚀脊形光波导能够满足多模干涉型器件的精确自镜像要求,并使输入/输出光波导在单模工作下有较大的横截面,较低的弯曲损耗及较小的耦合串扰.通道末端引入的模斑转换器可方便地与单模光纤连接耦合. 相似文献
3.
4.
5.
6.
7.
采用离散谱折射率法直接对三维脊形自镜像效应(SIE)多模波导的模式特性进行具体分析,并根据模式传播常数偏差分布情况,引入了SIE多模波导长度微小变量用以抵消或部分减弱由各阶模式传播常数偏差引起的相位偏差,设计了一种低自镜像损耗、高均匀度、几乎与偏振无关及深刻蚀SIE多模波导结构的多模干涉(MMI)光功分器。如1×16MMI光功分器TE模的自镜像损耗为0.0451dB,均匀度0.0309dB;对TE模的自镜像损耗为0.0455dB,均匀度为0.0311dB。 相似文献
8.
设计并制作了阻塞型和完全无阻塞型4×4热光SOI(silicon-on-insulator)波导开关阵列。开关单元采用了多模干涉耦合器(MMI)-MZI(Mach-Zehnder interferometer)结构的2×2光开关。阻塞型光开关附加损耗为4.8~5.4dB,串扰为-21.8dB~-14.5dB。完全无阻塞型光开关阵列附加损耗为6.6~9.6dB,串扰为-25.8~-16.8dB。两者的消光比都在17~25dB内变化,开关单元功耗小于230mW。器件的开关时间小于3μs。功耗和开关速度都明显优于SiO2基和聚合物基的开关阵列。 相似文献
9.
10.
基于SOI的2×2 MMI耦合器的设计 总被引:1,自引:1,他引:0
设计了一种可用于阵列波导光栅(AWG)解调集成微系统的绝缘体上硅(SOI)基2×2多模干涉(MMI)耦合器,用光束传播法(BPM)对MMI耦合器进行了模拟。耦合器输入/输出波导采用倒锥形,多模干涉区尺寸为6μm×57μm。在TE偏振中心波长为1.55μm时,器件附加损耗为0.46dB,不均匀性为0.06dB。在1.49~1.59μm波长范围内耦合器的附加损耗小于1.55dB。仿真结果表明所设计的2×2MMI耦合器体积小、附加损耗低、波长响应范围宽、分光均匀,符合片上集成系统的要求。 相似文献
11.
12.
13.
14.
15.
Lasing at 1.3 μ upon flash photolysis of 2-2-2 tri-fluoroethyliodide, CF3 CH2 I, has been observed on the2P_{1/2} -2P_{3/2} magnetic dipole allowed transition of atomic iodine. Using an 800-J flash, a maximum peak power output of approximately 108 W for 10-μs duration at half-maximum intensity was obtained with a pressure of 17 torr CF3 CH2 I. 相似文献
16.
17.
氟氧化物玻璃陶瓷综合了传统激光晶体和激光玻璃的优点,是近年来激光材料研究的新热点。我们制备了掺杂Er离子的SiO2-Al2O3-PbF2-ZnF2玻璃陶瓷材料,并对其显微结构进行了初步研究。 相似文献
18.
K. C. Goretta V. R. Todt D. J. Miller M. T. Lanagan Y. L. Chen U. Balachandran J. Guo J. A. Lewis 《Journal of Electronic Materials》1995,24(12):1961-1966
Three methods were used to introduce flux-pinning centers into Bi2Sr2CaCu2Ox (Bi-2212) and TlBa2Ca2Cu3Ox (Tl-1223) samples. It was found that carbon induced local decomposition, that nanosized Al2O3 additions created stable reaction products, and that second phases could be isolated in Tl-1223 during synthesis. Each of
these defects enhanced flux pinning and was of most benefit at temperatures ≤ 35K. 相似文献
19.
Y. F. Li M. E. Loomans K. C. Goretta S. E. Dorris M. T. Lanagan R. B. Poeppel J. J. Wenzlaff P. M. Winandy C. A. Youngdahl U. Balachandran P. Kostic 《Journal of Electronic Materials》1994,23(11):1163-1167
Three phase assemblages were used to produce Bi2Sr2CaCu2Ox (2212) during sintering: a mixture of 20% Ca-rich 2212+80%2212, partially synthesized 2212, and Bi2Sr2CuOx (2201)+(1/2 Ca2 CuO3+1/2 CuO) (denoted 0011). The mixture of 2201+0011 produced highly pure 2212 within 50 h of heating in air at ≈850°C. Ag tubes
were filled with a mixture of 2201+0011 and worked into tapes by a powder-in-tube process. Heat treatments produced microstructures
consisting of small, highly textured 2212 grains. Tc values were ≈70K. Transport Jc values at 4.2K were ≈104 A/cm2. 相似文献
20.