具有低欧姆接触电阻的高性能AlGaN/GaN HEMT器件研制

研究了AlGaN/GaN HEMT器件Ti/Al/Ti/Au四层金属结构欧姆接触的形成过程.通过系统研究退火条件获得了较低的欧姆接触电阻,实现了10-7Ω·cm2的欧姆接触率,并在此基础上对AlGaN/GaN HEMT欧姆接触形成机理进行了深入讨论.通过器件工艺的优化,研制了高性能的AlGaN/GaN HEMT器件.栅宽40μm的器件跨导达到250mS/mm,fT达到70GHz;栅宽0.8mm的功率器件电流密度达到1.07A/mm(Vg=0.5V),Vds=30V时,8GHz工作频率下(在片测试)器件的输出功率为32.5dBm(1.6W),输出功率密度达到2.14W/mm,功率增益为12.7dB.     

具有低欧姆接触电阻的高性能AlGaN/GaN HEMT器件研制

研究了AlGaN/GaN HEMT器件Ti/Al/Ti/Au四层金属结构欧姆接触的形成过程.通过系统研究退火条件获得了较低的欧姆接触电阻,实现了10-7Ω·cm2的欧姆接触率,并在此基础上对AlGaN/GaN HEMT欧姆接触形成机理进行了深入讨论.通过器件工艺的优化,研制了高性能的AlGaN/GaN HEMT器件.栅宽40μm的器件跨导达到250mS/mm,fT达到70GHz;栅宽0.8mm的功率器件电流密度达到1.07A/mm(Vg=0.5V),Vds=30V时,8GHz工作频率下(在片测试)器件的输出功率为32.5dBm(1.6W),输出功率密度达到2.14W/mm,功率增益为12.7dB.     

非掺杂AlGaN/GaN微波功率HEMT

报道了研制的AlGaN/GaN微波功率HEMT,该器件采用以蓝宝石为衬底的非掺杂AlGaN/GaN异质结构,器件工艺采用了Ti/Al/Ni/Au欧姆接触和Ni/Au肖特基势垒接触以及SiN介质进行器件的钝化.研制的200μm栅宽T型布局AlGaN/GaN HEMT在1.8GHz,Vds=30V时输出功率为28.93dBm,输出功率密度达到3.9W/mm,功率增益为15.59dB,功率附加效率(PAE)为48.3%.在6.2GHz,Vds=25V时该器件输出功率为27.06dBm,输出功率密度为2.5W/mm,功率增益为10.24dB,PAE为35.2%.     

X波段高输出功率凹栅AlGaN/GaN HEMT

使用自主研制的SiC衬底GaN HEMT外延材料,研制出高输出功率AlGaN/GaN HEMT,优化了器件研制工艺,比接触电阻率小于1.0×10-6Ω·cm2,电流崩塌参量小于10%,击穿电压大于80V.小栅宽器件工作电压达到40V,频率为8GHz时输出功率密度大于10W/mm.栅宽为2mm单胞器件,工作电压为28V,频率为8GHz时,输出功率为12.3W,功率增益为4.9dB,功率附加效率为35%.四胞内匹配总栅宽为8mm器件,工作电压为27V时,频率为8GHz时,输出功率为33.8W,功率增益为6.3dB,功率附加效率为41.77%,单胞器件和内匹配器件输出功率为目前国内该器件输出功率的最高结果.     

X波段高输出功率凹栅AlGaN/GaN HEMT

使用自主研制的SiC衬底GaN HEMT外延材料,研制出高输出功率AlGaN/GaN HEMT,优化了器件研制工艺,比接触电阻率小于1.0×10-6Ω·cm2,电流崩塌参量小于10%,击穿电压大于80V.小栅宽器件工作电压达到40V,频率为8GHz时输出功率密度大于10W/mm.栅宽为2mm单胞器件,工作电压为28V,频率为8GHz时,输出功率为12.3W,功率增益为4.9dB,功率附加效率为35%.四胞内匹配总栅宽为8mm器件,工作电压为27V时,频率为8GHz时,输出功率为33.8W,功率增益为6.3dB,功率附加效率为41.77%,单胞器件和内匹配器件输出功率为目前国内该器件输出功率的最高结果.     

高性能1mm SiC基AlGaN/GaN功率HEMT研制

在6H-SiC衬底上,外延生长了AlGaN/GaN HEMT结构,设计并实现了高性能1mm AlGaN/GaN微波功率HEMT,外延材料利用金属有机物化学气相淀积技术生长.测试表明,该lmm栅宽器件栅长为0.8μm,输出电流密度达到1.16A/mm,跨导为241mS/mm,击穿电压＞80V,特征频率达到20GHz,最大振荡频率为28GHz.5.4GHz连续波测试下功率增益为14.2dB,输出功率达4.1W,脉冲条件测试下功率增益为14.4dB,输出功率为5.2W,两端口阻抗特性显示了在微波应用中的良好潜力.     

高性能1mm SiC基AlGaN/GaN功率HEMT研制

在6H-SiC衬底上,外延生长了AlGaN/GaN HEMT结构,设计并实现了高性能1mm AlGaN/GaN微波功率HEMT,外延材料利用金属有机物化学气相淀积技术生长.测试表明,该lmm栅宽器件栅长为0.8μm,输出电流密度达到1.16A/mm,跨导为241mS/mm,击穿电压＞80V,特征频率达到20GHz,最大振荡频率为28GHz.5.4GHz连续波测试下功率增益为14.2dB,输出功率达4.1W,脉冲条件测试下功率增益为14.4dB,输出功率为5.2W,两端口阻抗特性显示了在微波应用中的良好潜力.     

14W X波段AlGaN/GaN HEMT功率MMIC

报道了研制的SiC衬底AIGaN/GaN HEMT微带结构微波功率MMIC,芯片工艺采用凹槽栅场板结构提高AlGaN/GaNHEMTs的微波功率特性.S参数测试结果表明AlGaN/GaN HEMTs的频率特性随器件的工作电压变化显著.研制的该2级功率MMIC在9～11GHz带内30V工作,输出功率大于10W,功率增益大于12dB,带内峰值输出功率达到14.7W,功率增益为13.7dB,功率附加效率为23%,该芯片尺寸仅为2.0mm×1.1mm.与已发表的X波段AlGaN/GaN HEMT功率MMIC研制结果相比,本项工作在单位毫米栅宽输出功率和芯片单位面积输出功率方面具有优势.     

14W X波段AlGaN/GaN HEMT功率MMIC

报道了研制的SiC衬底AIGaN/GaN HEMT微带结构微波功率MMIC,芯片工艺采用凹槽栅场板结构提高AlGaN/GaNHEMTs的微波功率特性.S参数测试结果表明AlGaN/GaN HEMTs的频率特性随器件的工作电压变化显著.研制的该2级功率MMIC在9～11GHz带内30V工作,输出功率大于10W,功率增益大于12dB,带内峰值输出功率达到14.7W,功率增益为13.7dB,功率附加效率为23%,该芯片尺寸仅为2.0mm×1.1mm.与已发表的X波段AlGaN/GaN HEMT功率MMIC研制结果相比,本项工作在单位毫米栅宽输出功率和芯片单位面积输出功率方面具有优势.     

非掺杂AlGaN/GaN微波功率HEMT

报道了研制的Al Ga N / Ga N微波功率HEMT,该器件采用以蓝宝石为衬底的非掺杂Al Ga N/ Ga N异质结构,器件工艺采用了Ti/ Al/ Ni/ Au欧姆接触和Ni/ Au肖特基势垒接触以及Si N介质进行器件的钝化.研制的2 0 0μm栅宽T型布局Al Ga N / Ga N HEMT在1.8GHz,Vds=30 V时输出功率为2 8.93d Bm,输出功率密度达到3.9W/mm ,功率增益为15 .5 9d B,功率附加效率(PAE)为4 8.3% .在6 .2 GHz,Vds=2 5 V时该器件输出功率为2 7.0 6 d Bm ,输出功率密度为2 .5 W/ mm ,功率增益为10 .2 4 d B,PAE为35 .2 % .     

Development of the readout system for waveguide multilayer optical card

Waveguide multilayer optical card （WMOC） is a novel storage device of three-dimensional optical information. An advanced readout system fitting for the WMOC is introduced in this paper. The hardware mainly consists of the light source for reading, WMOC, motorized stages addressing unit, microscope imaging unit, CCD detecting unit and PC controlling ＆ processing unit. The movement of the precision motorized stage is controlled by the computer through Visual Basic （VB） language in software. A control panel is also designed to get the layer address and the page address through which the position of the motorized stages can be changed. The WMOC readout system is easy to manage and the readout result is directly displayed on computer monitor.     

Nanoimprint Lithography -A Next Generation High Volume Lithography Technique

IntroductionNanoimprint Lithography is a well-acknowl-edged low cost, high resolution, large area pattern-ing process. It includes the most promising methods,high-pressure hot embossing lithography (HEL) [2],UV-cured imprinting (UV-NIL) [3] and micro contactprinting (m-CP, MCP) [4]. Curing of the imprintedstructures is either done by subsequent UV-lightexposure in the case of UV-NIL or by cooling downbelow the glass transition temperature of the ther-moplastic material in case of HEL…     

Collinear phase-matching study of terahertz-wave generation via difference frequency mixed in GaAs and Inp

The collinearly phase-matching condition of terahertz-wave generation via difference frequency mixed in GaAs and InP is theoretically studied. In collinear phase-matching, the optimum phase-matching wave hands of these two crystals are calculated. The optimum phase-matching wave bands in GaAs and lnP are 0.95-1.38μm and 0.7-0.96μm respectively. The influence of the wavelength choice of the pump wave on the coherent length in THz-wave tuning is also discussed. The influence of the temperature alteration on the phase-matching and the temperature tuning properties in GaAs crystal are calculated and analyzed. It can serve for the following experiments as a theoretical evidence and a reference as well.     

Effects of the alloy compositions on the phonon-polaritons in ternary mixed crystals

Composition dependence of bulk and surface phonon-polaritons in ternary mixed crystals are studied in the framework of the modified random-element-isodisplacement model and the Bom-Huang approximation. The numerical results for Several Ⅱ - Ⅵ and Ⅲ- Ⅴ compound systems are performed, and the polariton frequencies as functions of the compositions for ternary mixed crystals AlxGa1-xAs, GaPxAS1-x, ZnSxSe1-x, GaAsxSb1-x, GaxIn1-xP, and ZnxCd1-xS as examples are given and discussed. The results show that the dependence of the energies of two branches of bulk phonon-polaritons which have phonon-like characteristics, and surface phonon-polaritons on the compositions of ternary mixed crystals are nonlinear and different from those of the corresponding binary systems.     

Influence of PVK ： NPB hole transporting layer on the characteristics of organic light-emitting devices

A doping system consisting of NPB and PVK is employed as a composite hole transporting layer （CHTL）. By adjusting the component ratio of the doping system, a series of devices with different concentration proportion of PVK ： NPB are constracted. The result shows that doping concentration of NPB enhances the competence of hole transporting ability, and modifies the recombination region of charge as well as affects the surface morphology of doped film. Optimum device with a maximum brightness of 7852 cd/m^2 and a power efficiency of 1.75 lm/W has been obtained by choosing a concentration proportion of PVK ： NPB at 1：3.     

New insert layer structure OLEDs

An insert layer structure organic electroluminescent device（OLED） based on a new luminescent material （Zn（salen）） is fabricated. The configuration of the device is ITO/CuPc/NPD/Zn（salen）/Liq/LiF/A1/CuPc/NPD/Zn（salen）/Liq/LiF/A1. Effective insert electrode layers comprising LiF（1nm）/Al（5 nm） are used as a single semitransparent mirror, and bilayer cathode LiF（1 nm）/A1（100 nm） is used as a reflecting mirror. The two mirrors form a Fabry-Perot microcavity and two emissive units. The maximum brightness and luminous efficiency reach 674 cd/m^2 and 2.652 cd/A, respectively, which are 2.1 and 3.7 times higher than the conventional device, respectively. The superior brightness and luminous efficiency over conventional single-unit devices are attributed to microcavity effect.     

Analysis of error performance on Turbo coded FDPIM

Due to variable symbol length of digital pulse interval modulation（DPIM）, it is difficult to analyze the error performances of Turbo coded DPIM. To solve this problem, a fixed-length digital pulse interval modulation（FDPIM） method is provided. The FDPIM modulation structure is introduced. The packet error rates of uncoded FDPIM are analyzed and compared with that of DPIM. Bit error rates of Turbo coded FDPIM are simulated based on three kinds of analytical models under weak turbulence channel. The results show that packet error rate of uncoded FDPIM is inferior to that of uncoded DPIM. However, FDPIM is easy to be implemented and easy to be combined, with Turbo code for soft-decision because of its fixed length. Besides, the introduction of Turbo code in this modulation can decrease the average power about 10 dBm, which means that it can improve the error performance of the system effectively.     

A method for calculating the center position of collimated light

It is a key problem to accurately calculate beam spots＇ center of measuring the warp by using a collimated laser. A new method, named double geometrical center method （DGCM）, is put forward for the first time. In this method, a plane wave perpendicularly irradiates an aperture stop, and a charge couple device （CCD） is employed to receive the diffraction-beam spots, then the geometrical centers of the fast and the second diffraction-beam spots are calculated respectively, and their mean value is regarded as the center of datum beam. In face of such adverse instances as laser intension distributing defectively, part of the image being saturated, this method can still work well. What＇s more, this method can detect whether an unacceptable error exits in the courses of image receiving, processing and calculating. The experimental results indicate the precision of this method is high.     

Resolution Enhancement Technology:Integrated Process Solutions using OPC

DUV lithography, using the 248 nm wavelength, is a viable manufacturing option for devices with features at 130 nm and less. Given the low kl value of the lithography, integrated process development is a necessary method for achieving acceptable process latitude. The application of assist features for rule based OPC requires the simultaneous optimization of the mask, illumination optics and the resist.Described in this paper are the details involved in optimizing each of these aspects for line and space imaging.A reference pitch is first chosen to determine how the optics will be set. The ideal sigma setting is determined by a simple geometrically derived expression. The inner and outer machine settings are determined, in turn,with the simulation of a figure of merit. The maximum value of the response surface of this FOM occurs at the optimal sigma settings. Experimental confirmation of this is shown in the paper.Assist features are used to modify the aerial image of the more isolated images on the mask. The effect that the diffraction of the scattering bars (SBs) has on the image intensity distribution is explained. Rules for determining the size and placement of SBs are also given.Resist is optimized for use with off-axis illumination and assist features. A general explanation of the material' s effect is discussed along with the affect on the through-pitch bias. The paper culminates with the showing of the lithographic results from the fully optimized system.     

Cost-effective test solutions for smart card and other integrated flash applications

From its emergence in the late 1980s as a lower cost alternative to early EEPROM technologies, flash memory has evolved to higher densities and speedsand rapidly growing acceptance in mobile applications.In the process, flash memory devices have placed increased test requirements on manufacturers. Today, as flash device test grows in importance in China, manufacturers face growing pressure for reduced cost-oftest, increased throughput and greater return on investment for test equipment. At the same time, the move to integrated flash packages for contactless smart card applications adds a significant further challenge to manufacturers seeking rapid, low-cost test.