AZO晶种层对ZnO纳米线生长及紫外光电导性能的影响

采用溶液化学法实现了在Zn(NO3)2/C6H12N4混合溶液中ZnO纳米线在AZO薄膜修饰过衬底上生长。AZO薄膜由射频磁控溅射法制备,通过溅射时间和基底温度的变化改变薄膜形态,重点研究了不同薄膜形态对ZnO纳米线形貌和结构的影响,最终在溅射2h、基底温度250℃晶种上得到垂直于衬底、高度平行取向的ZnO纳米线阵列。在此基础上研究了不同形貌ZnO纳米线阵列的紫外光电导性能差异。结果表明,垂直生长的纳米线较倒伏纳米线紫外响应迅速,分析认为是紫外光照下曝光面积不同造成的。     

高压PLD法生长p型钠掺杂氧化锌纳米线阵列

采用高压脉冲激光沉积法(HP-PLD)研究了压强、金催化层厚度对钠掺杂氧化锌纳米线(ZnO:Na)生长的影响, 并制备了ZnO:Al薄膜/ZnO:Na纳米线阵列同质pn结器件。实验发现, 当金膜厚度为4.2 nm, 生长压强为3.33×10⁴ Pa, 生长温度为875℃时, 可在单晶Si衬底上生长c轴取向性良好的ZnO纳米线阵列。X射线衍射和X射线光电子能谱综合分析证实了Na元素成功掺入ZnO纳米线晶格中。在低温(15 K)光致发光谱中, 观测到了一系列由Na掺杂ZnO产生引起的受主光谱指纹特征, 如中性受主束缚激子峰(3.356 eV, A0X)、导带电子到受主峰(3.312 eV, (e, A0))和施主受主对发光峰(3.233 eV, DAP)等。通过在ZnO:Al薄膜上生长ZnO:Na纳米线阵列形成同质结, 测得I-V曲线具有明显的整流特性, 证实了ZnO:Na纳米线具有良好的p型导电性能。     

图案化ZnO纳米线阵列制备与应用的研究进展

综述了多种图案化制备ZnO纳米线阵列的技术,包括电子束光刻技术、纳米球蚀刻技术、激光干涉光刻技术、纳米压印技术和嵌段共聚物蚀刻技术等。介绍了图案化ZnO纳米线阵列在传感器、太阳能电池和UV检测器等功能器件中的应用进展,分析了图案化ZnO纳米线阵列制备与应用中的优点、意义及存在的问题,并展望了其未来发展趋势。     

ZnO/TiO_2复合纳米材料的制备及其在染料敏化太阳电池中的运用

本文在长有ZnO纳米粒子作为"种子层"的FTO基底上用水热合成法制备了取向高度一致的ZnO纳米线阵列,用TiCl4的异丙醇溶液在ZnO纳米线阵列的表面生长了纳米结构的TiO2。利用扫描电子显微镜、能量散射谱、X射线衍射分别表征纳米材料的形貌和结构,用Raman光谱研究了材料的晶格结构特性。染料敏化太阳电池的性能测试表明,与纯ZnO作为光阳极相比,ZnO/TiO2复合纳米材料作为光阳极的器件,开路电压和填充因子都得到了提高。     

Ag掺杂ZnO纳米线酒敏性能的研究

利用浸渍法将ZnO纳米线浸渍于AgNO3溶液中制备了Ag 掺杂的ZnO纳米线.借助X射线衍射仪(XRD)和场发射扫描电子显微镜(FESEM)对纳米线的晶体结构和形貌进行了表征.结果表明纳米线既含面心立方结构的Ag又含有六方纤锌矿结构的ZnO.三维网络结构的ZnO纳米线被一层致密的Ag颗粒包裹并在其表面形成了大量的具有高比表面剂的孔洞结构.将纯的和Ag掺杂的ZnO 纳米线都作为酒敏传感材料,在酒精浓度为0.001%,工作温度为150～400℃的范围内测试了它们的气敏特性,结果显示,Ag掺杂的ZnO纳米线的酒精灵敏度比纯ZnO纳米线提高了14.在工作温度为350℃的条件下测试了它们的响应-恢复时间.气敏元件的酒敏特性主要归结于表面吸附效应.     

反应源温度对ZnO纳米线阵列定向性及发光性能的影响

以Au薄膜为催化剂、ZnO与碳混合粉末为反应源,采用碳热还原法在单晶Si衬底上制备了ZnO纳米线阵列.通过扫描电子显微镜( SEM)、X射线衍射仪(XRD)、荧光分光光度计对样品的表征,研究了反应源温度对ZnO纳米线阵列的定向性和光致发光性能的影响.样品在源温度920℃条件下沿(002)方向择优生长,定向性最好,温度过低不利于ZnO纳米线阵列密集生长,而温度过高导致Zn原子二次蒸发,因而也不利于纳米线阵列的定向和择优生长;样品在源温度880℃有最强的近紫外带边发射,表明温度过高和过低都不利于ZnO晶体结构的优化;由于ZnO纳米线在缺氧氛围下生长,氧空位是缺陷存在的主要形式,因此所有样品都有较强的绿光发射.温度升高导致纳米线生长速度提高而增加了氧空位缺陷数量,从而使样品绿峰强度增强并在源温度920℃时达最大值,但温度的进一步升高可导致ZnO纳米线表面Zn元素的蒸发而降低氧空位缺陷的数量,从而抑制绿峰强度.     

ZnO纳米线的制备及场发射特性的研究进展

从ZnO纳米线的生长机制出发,重点讨论了催化剂在制备过程中的作用,比较了采用VLS和VS不同机制生长ZnO纳米线的优缺点,并结合二者特点发现采用金属自催化将是制备高质量ZnO纳米线阵列的一种有效方法.分析了几种有利于提高其场发射性能的后处理方法,经过适当的后处理ZnO纳米线晶体的结构将更加完善,场发射开启场、阈值场将进一步降低,电流密度和场增强因子也将随之大大提高.     

ZnO纳米线阵列的图形化生长

采用光刻和射频磁控溅射技术在Si衬底上制备了图形化的ZnO种子层薄膜。分别采用气相榆运和水热合成法，制备了最小单元为30μm的图形化的ZnO纳米线阵列。X射线衍射（XRD）分析显示单晶纳米线阵列具有高度的c轴[001]择优取向生长性质，从扫描电子显微镜（SEM）照片看出，阵列图形完整清晰，边缘整齐，纳米线阵列在室温下光致发光（PL）谱线中在380hm左右具有强烈的紫外发射峰，可见光区域发射峰得到了抑制，证明ZnO纳米线阵列氧空位缺陷少，晶体质量高。     

基于ZnO半导体纳米线膜的声表面波型紫外探测器

针对传统半导体光电探测器件结构的宽带隙半导体紫外探测器可测信号弱的问题,提出了一种基于ZnO纳米线膜的声表面波型紫外探测器.该探测器利用ZnO纳米线膜的强紫外光电响应特性和声表面波器件的灵敏的声电相互作用机制,将采用高纯锌粉的热蒸发氧化工艺制备的纤锌矿型ZnO纳米线制作在已有声表面波小波传感器上.利用光致发光谱研究发现,由于低维激子限域效应和表面效应,所制作ZnO纳米线敏感膜中的紫外光电效应优于外延ZnO半导体薄膜;同时,基于ZnO纳米线膜的声表面波式紫外探测器在紫外光辐照下该探测器的中心频率减小,损耗增大.实验研究表明该器件能够实现长波紫外光的高灵敏度探测.     

紫光激发提高Ag修饰的ZnO纳米线的气敏特性

为了提高ZnO纳米线的酒敏特性,利用紫光激发经浸渍法获得Ag修饰的ZnO纳米线.利用扫描电子显微镜（SEM）,X射线衍射仪（XRD）对修饰后的ZnO纳米线进行了晶体结构和形貌的表征.结果表明其晶体结构中既有六方纤锌矿结构的ZnO,又有面心立方的Ag.三维网络结构的ZnO纳米线的表面被一层致密的具有高孔隙率的Ag颗粒覆盖,使得ZnO纳米线具有更高的比表面积.纯ZnO纳米线和Ag修饰的ZnO纳米线都用作气敏基料,根据它们在酒精蒸气中紫光照射和无紫光照射条件下电阻的变化来测定它们的气敏特性.结果显示紫光照射下经质量分数为6%AgNO3修饰的ZnO纳米线对酒精蒸气的最大灵敏度由75.8提高到175.77.此过程中光催化氧化-还原反应起到了重要作用.     

High density Si/ZnO core/shell nanowire arrays for photoelectrochemical water splitting

Si/ZnO core/shell nanowire (NW) arrays were fabricated using atomic layer deposition of ZnO shell on n-Si NW arrays prepared by metal assisted electroless etching method. Scanning electron microscopy, transmission electron microscopy and X-ray diffraction were utilized to characterize the core/shell structures. Water splitting performance of the core/shell structures was preliminarily studied. The Si/ZnO core/shell NW arrays yielded significantly higher photocurrent density than the planar Si/ZnO structure due to their low reflectance and high surface area. The photoelectrochemical efficiency was found to be 0.035 and 0.002 % for 10 μm-long Si/ZnO NW array and planar Si/ZnO sample, respectively. These results suggested that core/shell structure is superior to planar heterojunction for PEC electrode design. We demonstrated the dependence of photocurrent density on the length of the core/shell array, and analyzed the reasons why longer NW arrays could produce higher photocurrent density. The relationship between the thickness of ZnO shell and the photoconversion efficiency of Si/ZnO NW arrays was also discussed. By applying the core/shell structure in electrode design, one may be able to improve the photoelectrochemical efficiency and photovoltaic device performance.     

Morphological transformations induced by Co impurity in ZnO nanostructures prepared by rf-sputtering and their physical properties

Growth of uniform and vertically well aligned nanorods is a difficult process and becomes more complicated in case of ZnO nanorods on silicon (Si) substrate due to thermal instability of the Si substrate and large lattice mismatch (~?40%) between the substrate and the ZnO nanorods array. Growth of ZnO nanorods assisted by metal ion via rf-sputtering is a good technique; however, it needs many parameters to be controlled for desired growth and morphology of nanostructures. In this work, we report the morphological transformations of ZnO nanostructured thin film by simply controlling the concentration of Cobalt (Co) impurity in sputtering target. With the introduction of Co ions in ZnO matrix, the initial coalescence grain structure (pyramidal morphology) changes into columnar grains and as the concentration of Co ions increases further, a highly oriented ZnO nanorods array is obtained. The possible mechanism with the help of schematic diagram is also proposed for the morphological transformation of ZnO nanostructures. The vertically aligned nanorods show good optical properties as well as robust ferromagnetism at room temperatures. It has also been observed that with the dopant conc. increasing there was a significant decrease in the band gap energy. The structure and morphology of rf-sputtered nanostructured thin films were investigated by X-ray diffraction, field emission scanning electron microscopy, transmission electron microscopy and selected area electron diffraction. Interestingly, with Co conc. increasing in ZnO matrix results in decreasing LO modes in Raman spectroscopy. It can have strong influence on the magnetic properties of the material. The good optical and strong ferromagnetic properties of the ZnO nanorods, suggest its possible applications in the fields of lasers, spintronics and medical applications.     

Ordered ZnO/AZO/PAM nanowire arrays prepared by seed-layer-assisted electrochemical deposition

An Al-doped ZnO (AZO) seed layer is prepared on the back side of a porous alumina membrane (PAM) substrate by spin coating followed by annealing in a vacuum at 400 °C. Zinc oxide in ordered arrays mediated by a high aspect ratio and an ordered pore array of AZO/PAM is synthesized. The ZnO nanowire array is prepared via a 3-electrode electrochemical deposition process using ZnSO₄ and H₂O₂ solutions at a potential of − 1 V (versus saturated calomel electrode) and temperatures of 65 and 80 °C. The microstructure and chemical composition of the AZO seed layer and ZnO/AZO/PAM nanowire arrays are characterized by field emission scanning electron microscopy (FE-SEM), high-resolution transmission electron microscopy (HR-TEM), and energy-dispersive X-ray spectroscopy (EDS). Results indicate that the ZnO/AZO/PAM nanowire arrays were assembled in the nanochannel of the porous alumina template with diameters of 110–140 nm. The crystallinity of the ZnO nanowires depends on the AZO seed layer during the annealing process. The nucleation and growth process of ZnO/AZO/PAM nanowires are interpreted by the seed-layer-assisted growth mechanism.     

ZnO纳米材料制备及其场发射性能的研究

采用水热法制备形貌和尺寸各异的纳米ZnO材料。用X射线衍射分析仪(XRD)和扫描电子显微镜(SEM)测试产物结构和表面形貌,分析影响纳米ZnO材料生长的因素,探讨纳米ZnO的生长机理。研究了各种形貌ZnO阵列的场致发射特性。实验结果表明,在各种ZnO纳米结构中,纳米管的场致发射性能最好,其最大电流密度可达到0.2mA/cm2,开启场强2.5V/μm,为寻求良好场发射性能的ZnO纳米材料提供了一个可行的途径。     

Reshaping the tips of ZnO nanowires by pulsed laser irradiation

Vertically aligned ZnO nanowires have been synthesized by a hydrothermal method. After being irradiated by a short laser pulse, the tips of the as-synthesized ZnO nanowires can be tailored into a spherical shape. Transmission electron microscopy revealed that the spherical tip is a single-crystalline piece connected to the body of the ZnO nanowire, and that the center of the sphere is hollow. The growth mechanism of the hollow ZnO nanospheres is proposed to involve laser-induced ZnO evaporation immediately followed by re-nucleation in a temperature gradient environment. The laser-irradiated ZnO nanowire array shows hydrophobic properties while the original ZnO nanowire array shows hydrophilicity. The as-grown ZnO nanowire arrays with hollow spherical tips can serve as templates to grow ZnO nanowire arrays with very fine tips, which may be a good candidate material for use in field emission and scanning probe microscopy.      

Photovoltaic properties of a ZnO nanorod array affected by ethanol and liquid-crystalline porphyrin

A vertically aligned array of ZnO nanorods, fabricated on conductive ITO substrate in aqueous solution, was characterized by scanning electron microscopy (SEM), x-ray diffraction (XRD), and UV-visible transmission spectroscopy. Surface photovoltage (SPV) techniques based on a lock-in amplifier and a Kelvin probe were both employed to study the photogenerated charges in the system. The effects of ethanol solvent and a liquid-crystalline porphyrin, [5-(para-dodecyloxy)phenyl-10,15,20-tri-phenyl] porphyrin (DPTPP), on the photovoltage enhancement in the ZnO nanorod array were studied via SPV comparison between different irradiation directions on the system. We demonstrate that the ethanol adsorption could induce the space charge region to expand towards the ZnO/ITO interface. In the absence of ethanol, the ZnO nanorod array with the DPTPP adsorption showed enhanced SPV with reduced attenuation rate of photogenerated charge carriers. We found that the separation of photogenerated charges could be further improved by coating the surface with DPTPP and ethanol together. Furthermore, the SPV spectra patterns of the composite system with opposite incident-light directions reveal that the DPTPP molecules adsorbed just at the surface of ZnO nanorods adopt a more monomeric alignment in contrast to the aggregative state in the DPTPP bulk.     

Fabrication of 3D interconnected porous TiO2 nanotubes templated by poly(vinyl chloride-g-4-vinyl pyridine) for dye-sensitized solar cells

Porous TiO(2) nanotube arrays with three-dimensional (3D) interconnectivity were prepared using a sol-gel process assisted by poly(vinyl chloride-graft-4-vinyl pyridine), PVC-g-P4VP graft copolymer and a ZnO nanorod template. A 7 μm long ZnO nanorod array was grown from the fluorine-doped tin oxide (FTO) glass via a liquid phase deposition method. The TiO(2) sol-gel solution templated by the PVC-g-P4VP graft copolymer produced a random 3D interconnection between the adjacent ZnO nanorods during spin coating. Upon etching of ZnO, TiO(2) nanotubes consisting of 10-15 nm nanoparticles were generated, as confirmed by wide-angle x-ray scattering (WAXS), energy-filtering transmission electron microscopy (EF-TEM) and field-emission scanning electron microscopy (FE-SEM). The ordered and interconnected nanotube architecture showed an enhanced light scattering effect and increased penetration of polymer electrolytes in dye-sensitized solar cells (DSSC). The energy conversion efficiency reached 1.82% for liquid electrolyte, and 1.46% for low molecular weight (M(w)) and 0.74% for high M(w) polymer electrolytes.     

ZnO纳米线阵列修饰对材料表面浸润性调控

采用溶胶-凝胶法制备了ZnO薄膜,利用溶剂热沉积法获得大面积均匀ZnO纳米线阵列。通过对水在ZnO材料表面的浸润性研究,发现薄膜材料表面的粗糙度对ZnO膜亲水性有增强作用,而周期性ZnO阵列微结构表面可以实现其疏水性质增强效果。同时从理论上分析了这两种现象的物理机制,讨论了空气填隙对ZnO纳米线阵列表面的浸润性质的敏感性。制备出ZnO纳米线阵列的表观接触角约为103°,具有较强的疏水性质,可为进一步的ZnO光流控研究提供实验基础。     

ZnO单晶堆垒纳米棒的制备与表征

在Au点阵模板上磁控溅射ZnO薄膜,然后在O2气氛下1000℃退火制备了ZnO单晶堆垒纳米棒。采用扫描电子显微镜(SEM)、高分辨透射电子显微镜(HRTEM)、X射线衍射(XRD)和傅立叶变换红外(FTIR)光谱对样品进行分析。结果表明,ZnO纳米棒是由诸多单晶堆垒而成,每个单晶均为六方纤锌矿结构,纳米棒直径在100nm左右。初步探讨了ZnO单晶堆垒纳米棒可能的生长机理。     

ZnO纳米棒阵列膜的制备及其光电化学性能研究

采用化学溶液沉积法,在ZnO纳米颗粒膜修饰的FTO导电玻璃基底上,制备了ZnO纳米棒阵列。用X射线衍射仪（XRD）、场发射扫描电子显微镜（FESEM）、透射电子显微镜（TEM）对样品进行表征。研究结果表明所制备的ZnO纳米棒为六方纤锌矿相单晶结构,沿c轴择优取向生长,平均直径约为40nm,长度约为900nm;ZnO纳米棒阵列生长致密,取向性较一致。以曙红Y敏化的ZnO纳米棒阵列膜为光阳极制作了染料敏化太阳能电池原型器件,在光照强度为100mW/cm2下,其开路电压为0.418V,短路电流为0.889mA/cm2,总的光电转换效率为0.133%。