直流溅射工艺参数对Mo薄膜结构及电性能的影响

采用直流磁控溅射法在SLG衬底上沉积Mo薄膜,对不同溅射功率和溅射工作气压下沉积的薄膜进行X射线衍射、SEM(扫描电子显微镜)、电阻率测试,讨论了工艺参数对沉积Mo薄膜相结构、表面微观形貌、薄膜沉积速率和电学性能的影响。结果表明,随着溅射功率的增加,薄膜的结晶性能变好,沉积速率提高,在沉积功率范围内薄膜均匀致密,表面无空隙,电阻率较低;随着溅射工作气压增加,薄膜结晶性能变差,沉积速率先增加后降低,在沉积工作气压范围内,薄膜致密;随气压降低,电阻率急剧减小。因此,较高的溅射功率和较低的工作气压沉积的Mo薄膜更适合作CIGS薄膜太阳电池的BC层(背接触层)。     

不同溅射功率下PEN/Ti纳米复合薄膜的制备及性能研究

采用直流磁控溅射法,在溅射气压为7.0×10~(-1) Pa和不同溅射功率(72～144W)下,制备出PEN/Ti纳米复合薄膜。研究了不同溅射功率对Ti膜微观组织、表面粗糙度、硬度及生长方式的影响规律。结果表明,直流磁控溅射法在PEN柔性衬底上沉积的钛膜是一种纳米多晶薄膜;随着溅射功率的增加,钛膜沉积速率及钛膜弹性模量皆升高,而钛膜表面粗糙度与钛膜晶粒尺寸均减小;溅射功率的增加将抑制钛膜柱状生长方式。在溅射气压为7.0×10~(-1) Pa,溅射功率为144 W时的工艺参数下,获得性能最佳的复合薄膜。     

磁控溅射TiN薄膜的工艺及电学性能研究

采用反应直流磁控溅射法,在Si基底上制备TiN薄膜.研究了溅射沉积过程中溅射气压和Ar/N2气体流量比对TiN薄膜结构及其电学性能的影响,并对试验结果进行了分析.研究发现,在Ar/N2气体流量比为15:1时,TiN薄膜的表面均方根粗糙度和电阻率都为最小.当溅射气压增大时,薄膜厚度减小.当溅射气压为0.3～0.5Pa时,薄膜表面较光滑,电阻率较小.     

磁控溅射制备大面积ZnO薄膜性能的研究

通过磁控溅射氧化锌陶瓷靶材的方法在玻璃基片上制备ZnO薄膜,研究了溅射功率、溅射气压以及基片温度对ZnO薄膜相结构、禁带宽度及光学性能的影响.使用X射线衍射仪(XRD)分析了薄膜相结构,使用台阶仪测试薄膜厚度,采用薄膜测试仪测试薄膜的透过率,采用扫描电镜(SEM)观察薄膜表面形貌.结果表明:不同制备条件下均形成具有(0...     

室温下射频磁控溅射制备ZnO:Al透明导电薄膜及其性能研究

采用射频磁控溅射技术,在室温下,以ZnO:Al2O3(2%Al2O3(质量比))为靶材,在石英玻璃基底上,采用不同工艺条件制备了ZnO:Al(AZO)薄膜。使用扫描电子显微镜观察了薄膜的表面形貌,X射线衍射分析了薄膜的结构,四探针测量仪得到薄膜的表面电阻,轮廓仪测量了薄膜厚度,并计算了电阻率,最后采用分光光度计测量了薄膜的透过率;研究了溅射功率、溅射气压与薄膜厚度对薄膜电阻率及透过率的影响。结果表明:所制备的AZO薄膜具有(002)择优取向,并且发现薄膜厚度对薄膜的光电性能有明显影响,溅射气压和溅射功率对薄膜电学性能有较大影响,但是对薄膜透过率影响不大。当功率为1kW、溅射气压0.052Pa、AZO薄膜厚度为250nm时,其电阻率为8.38×10-4Ω·cm,波长在550nm处透过率为89%,接近基底的本底透过率92%。当薄膜厚度为1125 nm时薄膜的电阻率降至最低(6.16×10-4Ω·cm)。     

室温下射频磁控溅射制备ZnO∶Al透明导电薄膜及其性能研究

采用射频磁控溅射技术,在室温下,以ZnO∶Al203(2％Al2O3(质量比))为靶材,在石英玻璃基底上,采用不同工艺条件制备了ZnO∶Al(AzO)薄膜.使用扫描电子显微镜观察了薄膜的表面形貌,X射线衍射分析了薄膜的结构,四探针测量仪得到薄膜的表面电阻,轮廓仪测量了薄膜厚度,并计算了电阻率,最后采用分光光度计测量了薄膜的透过率;研究了溅射功率、溅射气压与薄膜厚度对薄膜电阻率及透过率的影响.结果表明:所制备的AZO薄膜具有(002)择优取向,并且发现薄膜厚度对薄膜的光电性能有明显影响,溅射气压和溅射功率对薄膜电学性能有较大影响,但是对薄膜透过率影响不大.当功率为1kW、溅射气压0.052 Pa、AZO薄膜厚度为250nm时,其电阻率为8.38×10-4Ω·cm,波长在550 nm处透过率为89％,接近基底的本底透过率92％.当薄膜厚度为1125 nm时薄膜的电阻率降至最低(6.16×10-4 Ω·cm).     

磁控溅射制备ITO薄膜光电性能的研究

采用直流磁控溅射方法在玻璃基底上制备了ITO薄膜.分别用分光光度计和四探针仪测试了所制备ITO薄膜在可见光区域内的透过率和电阻率,研究了溅射气压、氧氩流量比和溅射功率三个工艺参数对ITO薄膜光电性能的影响.研究结果表明,制备ITO薄膜的最佳工艺参数为:溅射气压0.6 Pa,氧氩流量比1:40,溅射功率108 W.采用此工艺参数制备的ITO薄膜在可见光区平均透过率为81.18％,薄膜电阻率为8.9197×10-3Ω·cm.     

室温直流磁控溅射制备ITO膜及光电性能研究

室温条件下,在玻璃衬底上,采用直流磁控溅射法制备了ITO膜.研究了溅射压强,氧流量和溅射功率等工艺参数对薄膜光电性能的影响.结果表明当Ar流量为44.2 sccm和溅射时间20 min等参数不变时,溅射气压0.7 Pa,氧流量0.62 sccm和溅射功率130 W为最佳工艺条件.并得到了电阻率5.02×10-4 Ω·cm,在可见光区平均透过率80%以上ITO薄膜.     

溅射功率和氧分压对ITO薄膜光电性能的影响研究

采用直流反应磁控溅射法制备了氧化铟锡(ITO)透明导电薄膜,通过四探针、紫外可见分光光度计、X射线衍射(XRD)、霍尔效应仪、扫描电镜(SEM)等对薄膜样品进行了表征,研究了溅射功率和氧分压对ITO薄膜微观结构和光电性能的影响,结果表明:溅射功率对ITO的光电性能影响较小,沉积速率随着溅射功率的增大而加快;随着氧分压的升高,载流子浓度降低,霍尔迁移率先增大后减小,电阻率逐渐增大。在优化的工艺条件下,制备了在可见光区平均透过率达85%、电阻率为1×10-4Ω.cm的光电性能优良的ITO薄膜。     

磁控溅射工艺参数对ZAO薄膜性能的影响

通过磁控溅射氧化铝锌陶瓷靶材的方法在玻璃基片上制备ZAO薄膜,研究了溅射电流、溅射气压、基片温度对ZAO膜电学及光学性能的影响,使用X射线衍射仪分析了薄膜相结构,使用台阶仪测试薄膜厚度,使用四探针方阻仪测试薄膜电阻率,采用紫外可见分光光度计测试薄膜透过率。结果表明:溅射电流增加可以改善ZAO薄膜的透过率与电阻率;溅射气压对薄膜的结晶性和透过率影响不大,但电阻率会随溅射气压的增大而上升;基体温度升高可以提高AZO薄膜的透过率与电导率。     

Certification Institutions Expected to Update and Transfer Information on Present Standards

Standards are the basis for production enterprises to organize production, ex-factory inspection, trade (delivery) and technical exchanges, product certification, quality arbitration and supervision.……     

The Research of Anti-Wear Properties of Organomolybdenum Compounds in the Engine Oils

A four-ball tester was used to evaluate the anti-wear performance of three kinds of organomolybdemun compounds in the engine oils, i. e., molybdenum dialkyldithiophosphate (MoDDP), molybdenum dialkyldithiocarbamate ( MoDTC), and sulphur and phosphorus freeorganomolybdeum (Molybdate). The results indicate that a low concentration of MoDDP doesn' t improve the anti-wear properties of the commercial engine oils, but a high concentration of MoDDP can obviously improve the anti-wear properties and the load-carrying capacity of the engine oils. MoDTC doesn' t improve the antiwear properties of the engine oils, but worsens the anti-wear properties of the oils. Signifi can timprove ment of frictional and wear characteristics is obtained with Molybdate added in the commercial engine oils and the formulated oils.     

Optimum-Simulation von Ernteprozessen

Zusammenfassung Bei der Gestaltung von Ernteprozessen — beispielsweise des Prozesses Mähdrusch, Körnertransport und -abnahme — als transportverbundene Fließarbeitsverfahren mit mindestens zwei verschiedenen Arbeitsmitteln gibt es einen großen Optimierungsspielraum. Solche Prozesse sind mehrstufige Bedienungsprozesse mit gemischter Anordnung der Bedienungseinrichtungen. Außerdem besitzen sie stark ausgeprägte räumliche Aspekte. Es wird vor allem gezeigt, welche Merkmale solcher Prozesse in Simulationsmodellen abgebildet sein müssen, welche Zielgrößen in Abhängigkeit von welchen Einflußgrößen unter Berücksichtigung welcher Prozeßbedingungen ermittelt werden sollten und wie der Bewertungsprozeß zur Ermittlung der gewünschten Informationen gestaltet werden muß.     

Certification Becomes Important for the I Quality; and Safety Supervision of the Chinese Liquor Sector

The end of 2007, over 200 unit products of more than 80 Chinese firms have passed the quality grade certification for liquor products. These products involve distilled spirits, beer, wine, yellow wine, fruit syrup wine and others, and cover over 80% of the national top-branded liquor products.……     

Deposition and Coating Properties on CVD Tungsten

Surface characterization and microstructure studies are performed on chemical vapor deposited (CVD) tungsten coating. There is about 2 μm thickness diffusion layer of tungsten in the molybdenum substrate. The thermal shock test shows tungsten coating has good adhesion with molybdenum substrate, but the elements of oxygen and carbon in the tungsten coating have the bad affection to the adhesion. The result of high-temperature diffusion experiment is the diffusion rate from molybdenum substrate to tungsten coating is faster.     

Analysis of marine hydrobiont lipid extracts as possible cryoprotective agents

We studied a combined effect of the cryoprotectants both of lipid and carbohydrate origin at the presence of DMSO or without it on cell viability and the RNA synthesis in the embryonic mollusc and echinoderm cell cultures obtained at different developmental stages. Cryoprotective properties of exogenous lipids correlated with their thermotropic behavior. Lipid extracts from marine hydrobiontes, which thermal transitions are characterized by relatively small part of calorimetric thermogram area lying at temperatures above 0 °C (6–18%), were found to possess a considerable cryoprotective activity. The results are discussed in relation to the prediction of the cryoprotective activity of lipid extracts for marine animal cells. In addition, it was found that marine invertebrate cells can be cryopreserved without DMSO at the presence of trehalose and lipid extracts of some marine hydrobiontes.     

Low-Temperature Properties of Silver

Pure silver is used extensively in the preparation of high-temperature superconductor wires, tapes, films, and other configurations in which the silver not only shields the superconducting material from the surrounding materials, but also provides a degree of flexibility and strain relief, as well as stabilization and low-resistance electrical contact. Silver is relatively expensive, but at this stage of superconductor development, its unique combination of properties seems to offer the only reasonable means of achieving usable lengths of conductor. In this role, the low-temperature physical (electrical, thermal, magnetic, optical) and mechanical properties of the silver all become important. Here we present a collection of properties data extracted from the cryogenic literature and, to the extent possible, selected for reliability.     

Early ironwork in Biscay: Survey,excavation, experimentation and materials characterization. An integral study of the mountainside ironworks (ferrerías de monte or “haizeolak”)

ABSTRACT

The production of iron in Biscay (Basque Country, Spain) has been a hallmark of this territory of the North of the Iberian Peninsula throughout its history. The Archaeology team of the Basque Country Mining Museum has spent 13 years, so far, studying the origins of this activity through the evidences left at the old pre-hydraulic iron production workshops known as mountainside ironworks (ferrerías de monte) or haizeolak. It has catalogued 170 archaeometallurgical sites of this type in Biscay, and the archeological excavation of some of them has led to the knowledge of the different stages of the production process that took place in these workshops. The team has also experimentally reproduced the work carried out in a mountainside ironworks from the High Middle Ages, and it has currently started the characterization process of this type of activity through the study of the collected materials.     

Brainstorming for ISO Strategy 2016-2020

正Responding to ISO’s appeal for survey for the to-be-developed ISO Strategy Plan for 2016-2020,SAC hosted a special workshop over the needs and comments of various fi elds on June 8 in Beijing.The workshop was attended by ISO President-elect and Ansteel General Manager Zhang Xiaogang,SAC Vice-Administrator Yu Xinli,and 30 experts from     

CNAS Passes APLAC's PTP Review

正The review group of Asia Pacific Laboratory Accreditation Cooperation(APLAC)carried out a 4-day peer review of the proficiency testing provider(PTP)for China National Accreditation Service for Conformity Assessment(CNAS)from July 28 to 31,2014.CNAS passed the PTP review with excellent performance.Two senior peer reviewers of APLAC made a comprehensive,rigorous and detailed review of CNAS’s PTP accreditation activities,and made the on-spot inspection of the review groups in Shanghai and Shenzhen respectively.