HgCdTe红外探测器性能分析

根据碲镉汞材料的性能、碲镉汞红外探测器物理机理和基本器件模型,对截止波长为3 m、5 m、10.5 m的碲镉汞探测器,在不同工作温度下的探测率性能进行了理论计算。计算结果表明:碲镉汞探测器在短波、中波和长波三个主要红外波段均能满足第三代红外焦平面器件对灵敏度和工作温度的要求。     

长波p-on-n碲镉汞红外焦平面器件高温工作性能

碲镉汞材料为窄禁带半导体,随着工作温度的升高,材料本征载流子浓度会增加,探测器截止波长会变短,暗电流增加等,会导致器件性能降低。碲镉汞红外探测器通常在77 K温度附近工作并获得很好的探测性能,但低温工作会增加探测器的制备成本、功耗、体积和重量等。为了解决这些问题,在保证探测器正常工作性能的前提下,提升探测器的工作温度是碲镉汞红外探测器的重要研究方向。p-on-n结构的碲镉汞红外焦平面器件具有低暗电流、长少子寿命等特点,有利于在高工作温度条件下获得较好的器件性能。在不同工作温度下对p-on-n长波焦平面探测器的性能进行测试分析,在110 K时p-on-n长波碲镉汞红外焦平面探测器噪声等效温差（Noise Equivalent Temperature Difference , NETD）为25.3 mK,有效像元率为99.48%,在高温条件下具备较优的工作性能。     

碲镉汞高工作温度红外探测器

基于当前红外探测器技术的发展方向,从高工作温度红外探测器应用需求的角度分析了碲镉汞高工作温度红外探测器在组件重量、外形尺寸、功耗、环境适应性及可靠性方面的优势。总结了欧美等发达国家在碲镉汞高工作温度红外探测器研究方面的技术路线及研究现状。从器件暗电流和噪声机制的角度分析了碲镉汞光电器件在不同工作温度下的暗电流和噪声变化情况及其对器件性能的影响;总结了包括基于工艺优化的Hg空位p型n-on-p结构碲镉汞器件、基于In掺杂p-on-n结构和Au掺杂n-on-p结构的非本征掺杂碲镉汞高工作温度器件、基于nBn势垒阻挡结构的碲镉汞高工作温度器件及基于吸收层热激发载流子俄歇抑制的非平衡模式碲镉汞高工作温度器件在内的不同技术路线碲镉汞高工作温度器件的基本原理,对比分析了不同技术路线碲镉汞高工作温度器件的性能及探测器制备的技术难点。在综合分析不同技术路线高温器件性能与技术实现难度的基础上展望了碲镉汞高工作温度器件技术未来的发展方向,认为基于低浓度掺杂吸收层的全耗尽结构器件具备更好的发展潜力。     

HgCdTe艰辛的历程、辉煌的成就:一、伟大的发明

根据半个多世纪碲镉汞材料、碲镉汞红外探测器的发展里程,以碲镉汞材料的发明、关键技术突破带来的碲镉汞材料生长技术的进步、关键技术的突破带来的碲镉汞探测器性能提升、第一代陆军通用组件、第二代高性能红外焦平面器件和第三代高清、多波段红外焦平面器件等重要里程碑为出发点,采用专题系列的形式,回顾碲镉汞材料及碲镉汞红外探测器发展的...     

通过成结模拟器研究n+-n--p碲镉汞高温探测器

第三代红外探测器发展的一个重要方向是高工作温度探测器。对于碲镉汞n-on-p探测器而言,n⁺-n^--p结构以及良好的钝化工艺能够有效的抑制暗电流的产生,从而在高工作温度条件下获得较好的探测器性能。基于自行开发的成结模拟器,对n⁺-n^--p结构的高温器件进行了工艺仿真和器件仿真,获得成结过程的制备参数,并结合抑制表面漏电的组分梯度钝化工艺,将高工作温度下的暗电流抑制至理论极限,研制出可以在更高温度工作下的碲镉汞n-on-p红外焦平面探测器。经测试,中波n-on-p红外焦平面器件在不同工作温度下性能优异,在80K工作温度下噪声等效温差（NETD）达到了6.1 mK,有效像元率为99.96%;而在150K工作温度下噪声等效温差（NETD）为11.0 mK,有效像元率为99.50%,达到了同类器件的理论极限。     

3英寸Si基碲镉汞分子束外延工艺研究

随着红外焦平面阵列规模的扩大,由于尺寸和成本的限制,传统晶格匹配的碲锌镉衬底逐渐成为碲镉汞红外焦平面探测器发展的瓶颈,大尺寸、低成本硅基碲镉汞材料应运而生。本文采用分子束外延工艺生长获得了3 in Si基中波碲镉汞薄膜材料,通过采用金相显微镜、傅里叶红外光谱仪、双晶X射线衍射仪、湿化学腐蚀位错密度(EPD)法、Hall测试系统等检测手段对Si基中波碲镉汞分子束外延薄膜材料进行表面、光学、结构和电学性能表征,并采用标准平面器件工艺制备中波640×512焦平面探测阵列进行材料验证,结果表明该材料性能与国际先进水平相当。     

碲镉汞红外焦平面器件技术进展

近十年碲镉汞第二代红外焦平面探测器应用呈现爆发式增长,也是第三代焦平面技术快速发展的十年。文中对近十年来碲镉汞红外焦平面探测器技术的发展进行了简单的回顾,并结合碲镉汞红外焦平面探测器的应用,对在碲镉汞红外焦平面探测器技术方面的研究工作和工程应用进行了总结,最后,对未来碲镉汞红外焦平面探测器技术的发展进行了展望。     

高温碲镉汞中波红外探测器的国内外进展

介绍了欧美发达国家在高工作温度碲镉汞中波红外探测器上的工艺技术路线及典型产品技术指标。对昆明物理研究所研制的基于标准n-on-p(Hg空位掺杂)工艺的中波640×512(15μm)探测器进行了高工作温度性能测试,测试结果显示器件性能基本达到国外产品的同期研制水平。     

利用刻蚀工艺制备碲镉汞雪崩光电二极管

碲镉汞雪崩光电二极管是第三代红外焦平面探测器的主要发展方向之一.提出一种利用离子束刻蚀工艺制备碲镉汞雪崩光电二极管器件的方法,并研究了截止波长、耗尽区厚度与器件增益的关系.利用此方法制备截止波长4. 8μm的中波器件在17 V反向偏置下增益可达1 000.对器件进行了噪声频谱测试,计算了其过剩噪声因子.     

基于非平衡模式的碲镉汞高工作温度探测器

本文回顾了当前国内外高工作温度碲镉汞红外探测器的技术路线和相应的器件性能,在碲镉汞器件暗电流的温度特性分析的基础上,讨论了基于非平衡工作模式的碲镉汞探测器的基本原理、器件结构设计和暗电流机制,探讨了吸收层全耗尽碲镉汞器件性能与器件结构参数、材料晶体质量的关系,明确了其技术要点和难点,展望了碲镉汞高工作温度器件技术的发展趋势。     

Curved crystal spectrometer for the measurement of X-ray lines from laser-produced plasmas

In order to diagnose the laser-produced plasmas, a focusing curved crystal spectrometer has been developed for measuring the X-ray lines radiated from a laser-produced plasmas. The design is based on the fact that the ray emitted from a source located at one focus of an ellipse will converge on the other focus by the reflection of the elliptical surface. The focal length and the eccentricity of the ellipse are 1350 mm and 0.9586, respectively. The spectrometer can be used to measure the X- ray lines in the wavelength range of 0.2-0.37 nm, and a LiF crystal （200） （2d = 0.4027 nm） is used as dispersive element covering Bragg angle from 30° to 67.5°. The spectrometer was tested on Shengnang- Ⅱ which can deliver laser energy of 60-80 J/pulse and the laser wavelength is 0.35 μm. Photographs of spectra including the 1 s2p ^1P1-1s^2 ^1S0 resonance line（w）, the 1s2p ^3P2-1s^2 1S0 magnetic quadrupole line（x）, the 1s2p ^3P1-1 s^2 ^1S0 intercombination lines（y）, the 1 s2p ^3S~1-1 s^2 ^1S0 forbidden line（z） in helium-like Ti Ⅹ Ⅺ and the 1 s2s2p ^2P3/2-1 s622s ^2S1/2 line（q） in lithium-like Ti Ⅹ Ⅹhave been recorded with a X-ray CCD camera. The experimental result shows that the wavelength resolution（λ/△ 2） is above 1000 and the elliptical crystal spectrometer is suitable for X-ray spectroscopy.     

Preparation and Characterization of TaN ALD Precursors

High purity organic-tantalum precursors for thin film ALD TaN were synthesized and characterized.Vapor pressure and thermal stability of these precursors were studied.From the vapor pressure analysis,it was found that TBTEMT has a higher vapor pressure than any other published liquid TaN precursor,including TBTDET,TAITMATA,and IPTDET.Thermal stability of the alkyl groups on the precursors was investigated using a 1H NMR technique.The results indicated that the tertbutylimino group is the most stable group on TBTDET and TBTEMT as compared to the dialkylamido groups.Thermal stability of TaN precursors decreased in the following order:TBTDET ＞ PDMAT ＞ TBTEMT.In conclusion,precursor vapor pressure and thermal stability were tuned by making slight variations in the ligand sphere around the metal center.     

Electronic Structure of Semiconductor Nanocrystals

This paper reviews our recent development of the use of the large-scale pseudopotential method to calculate the electronic structure of semiconductor nanocrystals, such as quantum dots and wires, which often contain tens of thousands of atoms. The calculated size-dependent exciton energies and absorption spectra of quantum dots and wires are in good agreement with experiments. We show that the electronic structure of a nanocrystal can be tuned not only by its size,but also by its shape. Finally,we show that defect properties in quantum dots can be significantly different from those in bulk semiconductors.     

Critical Stage Rule-Based Real Time Dispatch（RTD）System in Highly-Mixed-Products （HMP） FAB

An improving utilization and efficiency of critical equipments in semiconductor wafer fabrication facilities are concerned. Semiconductor manufacturing FAB is one of the most complicated and cost sensitive environments. A good dispatching tool will make big difference in equipment utilization and FAB output as a whole. The equipment in this paper is In-Line DUV Scanner. There are many factors impacting utilization and output on this equipment group. In HMP environment one of the issues is changing of reticule in this area and idle counts due to load unbalance between equipments. Here we'll introduce a rule-based RTD system which aiming at decreasing the number of recipe change and idle counts among a group of scanner equipment in a high-mixed-products FAB.     

GaAsSb/InAlAs PA DHBTs Grown by Production MBE

The epi material growth of GaAsSb based DHBTs with InAlAs emitters are investigated using a 4 × 100mm multi-wafer production Riber 49 MBE reactor fully equipped with real-time in-situ sensors including an absorption band edge spectroscope and an optical-based flux monitor. The state-of-the-art hole mobilities are obtained from 100nm thick carbon-doped GaAsSb. A Sb composition variation of less than ± 0.1 atomic percent across a 4 × 100mm platen configuration has been achieved. The large area InAlAs/GaAsSb/InP DHBT device demonstrates excellent DC characteristics,such as BVCEO＞6V and a DC current gain of 45 at 1kA/cm2 for an emitter size of 50μm × 50μm. The devices have a 40nm thick GaAsSb base with p-doping of 4. 5 × 1019cm-3 . Devices with an emitter size of 4μm × 30μm have a current gain variation less than 2% across the fully processed 100mm wafer. ft and fmax are over 50GHz,with a power efficiency of 50% ,which are comparable to standard power GaAs HBT results. These results demonstrate the potential application of GaAsSb/InP DHBT for power amplifiers and the feasibility of multi-wafer MBE for mass production of GaAsSb-based HBTs.     

Influence of polarization extinction ratio on distributed polarization coupling detection

Distributed polarization coupling in polarization-maintaining fibers can be detected by using a white light Michelson interferometer. This technique usually requires that only one polarization mode is excited. However, in practical measurement, the injection polarization direction could not be exactly aligned to one of the principal axes of the PMF, so the influence of the polarization extinction ratio should be considered. Based on the polarization coupling theory, the influence of the incident polarization extinction on the measurement result is evaluated and analyzed, and a method for distributed polarization coupling detection is developed when both two orthogonal eigenmodes are excited.     

Noise character analysis and the restraint of self-pulsation laser diodes

We calculate the Langevin noise sources of self-pulsation laser diodes, analyze the effects of active region noise and saturable-absorption region noise on the power fluctuation as well as period fluctuation, and propose a novel method to restrain the noise effects. A visible SIMULINK model is established to simulate the system, The results indicate that the effects of noise in absorption region can be ignored; that with the increase of DC injecting current, the noise effects enhance power jitter, and nevertheless, the period jitter is decreased; and that with external sinusoidal current modulating the self-pulsation laser diode, the noise-induced power jitter and period jitter can be suppressed greatly. This work is valuable for clock recovery in all-optical network.     

High-quality single-crystal CdSe nanoribbons and their optical properties

Large-scale synthesis of single-crystal CdSe nanoribbons is achieved by a modified thermal evaporation method, in which two-step-thermal-evaporation is used to control CdSe sources＇ evaporation. The synthesized CdSe nanoribbons are usually several micrometers in width, 50 nm in thickness, and tens to several hundred micrometers in length. Studies have shown that high-quality CdSe nanoribbons with regular shapes can be obtained by this method. Room-temperature photolumines-cence indicates that the lasing emission at 710 nm has been observed under optical pumping （266 nm） at power densities of 25-153 kW/cm^2. The full width half maximum （FWHM） of the lasing mode is 0.67 nm     

Propagation of hermite-cosh-gaussian beams passing through ABCD optical system with an annular aperture

By using the expansion of the aperture function into a finte sum of complex Gaussian functions, the corresponding analytical expressions of Hermite-cosh-Gaussian beams passing through annular apertured paraxially and symmetrically optical systems written in terms of ABCD matrix were derived, and they could reduce to the cases with squared aperture. In a similar way, the corresponding analytical expressions of cosh-Gaussian beams through annular apertured ABCD matrix were also given. The method could save more calculation time than that by using the diffraction integral formula directly.     

中国建立EB级存储实验室,致力云计算应用(英文)

正With the support of 863 programs,Sugon Information Industry Co.,Ltd.,set up a dawning EB-class storage laboratory to address massive data storage requirements and largescale cloud computing demonstration applications.The Dawning EB-class cloud storage system adopts advanced fault-tolerant architecture,efficient data fault-tolerant algorithms with user authentication and data encryption policies to deal with the"lost""wrong"and"stolen"problems of data for ensuring the reliability and safety of the EB-class storage system in the public network application environments.The Dawning EB-class Storage Laboratory taking advan-