直流磁控溅射工艺参数对β-FeSi_2薄膜性能的影响

采用室温直流磁控溅射Fe-Si组合靶的方法,经过后续Ar气氛围退火,在单晶Si(111)衬底上生长β-FeSi2薄膜。研究了溅射功率、工作气压、Ar气流量、沉积时间等工艺参数对β-FeSi2薄膜结构特性及电学特性的影响,通过Raman、Hall、X射线衍射(XRD)等测试对其性能进行表征,对工艺参数进行了优化,在溅射功率为80W、工作气压为1.3Pa和Ar气流量为35SCCM时溅射沉积Fe-Si薄膜,不仅可以得到单一相的β-FeSi2,而且薄膜结晶质量较好。最终,在上述实验条件下制备得到的未掺杂的β-FeSi2薄膜是n型导电的,β-FeSi2薄膜中载流子浓度约为3.3×1016cm-3,迁移率为381cm2/Vs。     

沉积条件对室温下磁控溅射AZO薄膜微结构与光电性能的影响

通过控制室温下射频磁控溅射过程中不同的氩气工作气压、溅射功率和沉积时间,在石英玻璃上沉积Al掺杂ZnO（AZO）薄膜,探究了三种工艺条件对制备的AZO薄膜的微结构及光电性能的影响。所制备的AZO薄膜经500℃退火后均为六方纤锌矿结构,具有优异的透明度,在可见光范围内的平均透过率均在86%以上。在气压0.25 Pa、功率200 W下,溅射时间为10 min时,薄膜的电阻率低至5.04×10^-3Ω·cm,而溅射时间为15 min时,Haacke性能指数最优,为0.314×10^-3Ω^-1。结果表明,磁控溅射制备的AZO薄膜的晶体结构、方阻和透过率等特性与制备过程中的气压、功率和时间密切相关,通过评价性能指数可指导优化AZO薄膜的制备工艺。     

铁电PLZT薄膜退火工艺的研究

在无氧气氛下，采用射频磁控溅射法制备了ＰＬｚＴ系列薄膜，对原位溅射薄膜进行了快速退火及常规退火处理，深入研究了退火工艺对铁电薄膜结构与性能的影响。认为采用常规退火工艺处理无氧溅射的薄膜时，铁电薄膜具有更好的晶体结构和铁电性能。     

射频磁控溅射法制备液晶光阀光导层的研究

采用射频磁控溅射的方法制备了用于液晶光阀光导层的氢化非晶硅薄膜,研究了工艺参数对氢化非晶硅薄膜透过率及光电导性能的影响。结果表明,薄膜的沉积速率随着溅射功率和衬底温度的升高呈先增加后减小的趋势,在衬底温度为300℃,溅射功率为300W左右沉积速率达到最大,在溅射2h后沉积速率随着溅射时间的增加而下降;薄膜的光吸收系数随衬底温度的升高而增大,随溅射功率的增加而减小;交流电导率随衬底温度和溅射功率的升高而下降;薄膜在可见光范围内透过率随着H分压的增大而增大,且吸收边发生蓝移。     

射频磁控溅射ITO薄膜对TOPCon太阳电池光电性能的影响

通过射频(RF)磁控溅射分别在光学玻璃基底上和多晶硅薄膜层上沉积了氧化铟锡(ITO)薄膜,采用Hall效应测试仪测试了ITO薄膜的电阻率和载流子浓度等参数,研究溅射功率和溅射时间等参数对ITO薄膜的光电特性影响.测试多晶Si对称结构沉积ITO薄膜前后及退火后的隐开路电压和反向饱和电流密度等参数,研究ITO薄膜对n型晶硅...     

直流磁控溅射制备非晶硅薄膜的研究

非晶硅薄膜（a-Si）是目前重要的光敏材料,在很多领域得到广泛应用。直流磁控溅射具有工艺简单．沉积温度低等优点,是制备薄膜的一种重要技术。采用直流磁控溅射工艺在玻璃基板上沉积薄膜,并对样品进行了退火处理。研究了沉积速率与溅射功率的关系。结果表明薄膜的沉积速率与溅射功率近似有线性关系。利用X射线衍射（XRD）对薄膜进行了分析鉴定,结果表明溅射的薄膜是非晶硅薄膜。利用扫描电子显微镜（SEM）对非晶硅薄膜的表面形貌进行了观察和分析,与X射线衍射测试的结果一致。所以．利用直流磁控溅射工艺能在常温下能快速制备出良好的非晶硅薄膜。     

相变型VO2薄膜的制备及其特性的研究

利用反应离子束溅射和后退火工艺制备一种新的相变型VO2薄膜,对该薄膜进行电学测试、XRD和光学透过率的测试。这种工艺制备出的相变型VO2薄膜相变温度更接近室温,XRD显示这种薄膜中有VO2、V2O5成分的存在。对这种薄膜的光学透过率测试表明,低温下薄膜的透过率是高温下薄膜透过率的近5倍。通过实验可以看出,氧气分压、退火温度、退火时间是影响制备新型相变型VO2薄膜的重要因素。     

直流磁控溅射ITO薄膜的正交试验分析

利用直流磁控溅射系统制备ITO薄膜,采用正交试验表格L32(48)安排试验.测试了薄膜的方阻和透过率,分析了8个工艺参数对薄膜电光特性的影响,其中沉积气压、氩氧流量比和退火温度的影响最大.分析得到优化工艺参数为:沉积气压2×133.322 4 mPa、氩氧流量比16∶0.5、退火温度427 ℃、靶基间距15、退火时间1 h、溅射功率300 W、退火氛围为真空、沉积温度227 ℃.在此工艺参数下制备的ITO薄膜方阻为17 Ω/□,电阻率为1.87×10-4Ω·cm,在可见光区域平均透过率为85.13%.     

直流磁控溅射制备非晶硅薄膜的研究

非晶硅薄膜(a-Si)是目前重要的光敏材料,在很多领域得到广泛应用.直流磁控溅射具有工艺简单,沉积温度低等优点,是制备薄膜的一种重要技术.采用直流磁控溅射工艺在玻璃基板上沉积薄膜,并对样品进行了退火处理.研究了沉积速率与溅射功率的关系.结果表明薄膜的沉积速率与溅射功率近似有线性关系.利用X射线衍射(XRD)对薄膜进行了分析鉴定,结果表明溅射的薄膜是非晶硅薄膜.利用扫描电子显微镜(SEM)对非晶硅薄膜的表面形貌进行了观察和分析,与X射线衍射测试的结果一致.所以,利用直流磁控溅射工艺能在常温下能快速制备出良好的非晶硅薄膜.     

氮气退火对锑掺杂氧化锡薄膜近红外阻隔性能的影响

采用射频磁控溅射的方法,用96at％SnO2/4at％Sb2O3陶瓷靶在玻璃表面制备了锑掺杂氧化锡(ATO)薄膜.研究了溅射功率、压强和后退火对薄膜近红外阻隔性能的影响,并采用Uv-Vis-NIR透射光谱、霍尔效应测试仪、XRD和SEM等设备对薄膜的性能和结构进行了测试和分析.结果表明,室温沉积的ATO薄膜近红外透光率较高,但在氮气中退火后,不同溅射压强和溅射功率下沉积的ATO薄膜的近红外透光率均显著降低.在氧含量为10％、压强为1.4Pa、溅射功率为200W时,室温下沉积的ATO薄膜在氮气中500℃下退火1h后,550nm处透光率由80.9％升高至85.8％,2 000 nm处透光率由84.6％下降至23.0％.     

Preparation and Characterization of TaN ALD Precursors

High purity organic-tantalum precursors for thin film ALD TaN were synthesized and characterized.Vapor pressure and thermal stability of these precursors were studied.From the vapor pressure analysis,it was found that TBTEMT has a higher vapor pressure than any other published liquid TaN precursor,including TBTDET,TAITMATA,and IPTDET.Thermal stability of the alkyl groups on the precursors was investigated using a 1H NMR technique.The results indicated that the tertbutylimino group is the most stable group on TBTDET and TBTEMT as compared to the dialkylamido groups.Thermal stability of TaN precursors decreased in the following order:TBTDET ＞ PDMAT ＞ TBTEMT.In conclusion,precursor vapor pressure and thermal stability were tuned by making slight variations in the ligand sphere around the metal center.     

Curved crystal spectrometer for the measurement of X-ray lines from laser-produced plasmas

In order to diagnose the laser-produced plasmas, a focusing curved crystal spectrometer has been developed for measuring the X-ray lines radiated from a laser-produced plasmas. The design is based on the fact that the ray emitted from a source located at one focus of an ellipse will converge on the other focus by the reflection of the elliptical surface. The focal length and the eccentricity of the ellipse are 1350 mm and 0.9586, respectively. The spectrometer can be used to measure the X- ray lines in the wavelength range of 0.2-0.37 nm, and a LiF crystal （200） （2d = 0.4027 nm） is used as dispersive element covering Bragg angle from 30° to 67.5°. The spectrometer was tested on Shengnang- Ⅱ which can deliver laser energy of 60-80 J/pulse and the laser wavelength is 0.35 μm. Photographs of spectra including the 1 s2p ^1P1-1s^2 ^1S0 resonance line（w）, the 1s2p ^3P2-1s^2 1S0 magnetic quadrupole line（x）, the 1s2p ^3P1-1 s^2 ^1S0 intercombination lines（y）, the 1 s2p ^3S~1-1 s^2 ^1S0 forbidden line（z） in helium-like Ti Ⅹ Ⅺ and the 1 s2s2p ^2P3/2-1 s622s ^2S1/2 line（q） in lithium-like Ti Ⅹ Ⅹhave been recorded with a X-ray CCD camera. The experimental result shows that the wavelength resolution（λ/△ 2） is above 1000 and the elliptical crystal spectrometer is suitable for X-ray spectroscopy.     

Electronic Structure of Semiconductor Nanocrystals

This paper reviews our recent development of the use of the large-scale pseudopotential method to calculate the electronic structure of semiconductor nanocrystals, such as quantum dots and wires, which often contain tens of thousands of atoms. The calculated size-dependent exciton energies and absorption spectra of quantum dots and wires are in good agreement with experiments. We show that the electronic structure of a nanocrystal can be tuned not only by its size,but also by its shape. Finally,we show that defect properties in quantum dots can be significantly different from those in bulk semiconductors.     

Critical Stage Rule-Based Real Time Dispatch（RTD）System in Highly-Mixed-Products （HMP） FAB

An improving utilization and efficiency of critical equipments in semiconductor wafer fabrication facilities are concerned. Semiconductor manufacturing FAB is one of the most complicated and cost sensitive environments. A good dispatching tool will make big difference in equipment utilization and FAB output as a whole. The equipment in this paper is In-Line DUV Scanner. There are many factors impacting utilization and output on this equipment group. In HMP environment one of the issues is changing of reticule in this area and idle counts due to load unbalance between equipments. Here we'll introduce a rule-based RTD system which aiming at decreasing the number of recipe change and idle counts among a group of scanner equipment in a high-mixed-products FAB.     

GaAsSb/InAlAs PA DHBTs Grown by Production MBE

The epi material growth of GaAsSb based DHBTs with InAlAs emitters are investigated using a 4 × 100mm multi-wafer production Riber 49 MBE reactor fully equipped with real-time in-situ sensors including an absorption band edge spectroscope and an optical-based flux monitor. The state-of-the-art hole mobilities are obtained from 100nm thick carbon-doped GaAsSb. A Sb composition variation of less than ± 0.1 atomic percent across a 4 × 100mm platen configuration has been achieved. The large area InAlAs/GaAsSb/InP DHBT device demonstrates excellent DC characteristics,such as BVCEO＞6V and a DC current gain of 45 at 1kA/cm2 for an emitter size of 50μm × 50μm. The devices have a 40nm thick GaAsSb base with p-doping of 4. 5 × 1019cm-3 . Devices with an emitter size of 4μm × 30μm have a current gain variation less than 2% across the fully processed 100mm wafer. ft and fmax are over 50GHz,with a power efficiency of 50% ,which are comparable to standard power GaAs HBT results. These results demonstrate the potential application of GaAsSb/InP DHBT for power amplifiers and the feasibility of multi-wafer MBE for mass production of GaAsSb-based HBTs.     

Technology innovation and process integrations for sub-100nm gate patterning

This paper presents a brief overview of the Applied Centura(R)DPS(R)system,configured with silicon etch DPS Ⅱ chamber, with emphasis on discussing tuning capability for CD uniformity control. It also presents the studies of etch process chemistry and film integration impact for an overall successful gate patterning development. Discussions will focus on resolutions to key issues, such as CD uniformity, line-edge roughness, and multilayer film etching integration.     

White organic light-emitting devices based on fac tris（2- phenylpyridine） iridium sensitized 5,6,11,12-tetraphenylnap -hthacene

We have fabricated the white organic light-emitting devices （WOLEDs） based on 4,4＇ -bis（2,2 -diphenyl vinyl）-1,1＇ - biphenyl （DPVBi） and phosphorescence sensitized 5,6,11,12,-tetraphenylnaphthacene （rubrene）. The device structure is ITO/2T-NATA （20 nm）/NPBX （20 nm）/CBP： x%Ir（ppy）3：0.5% rubrene （8 nm）/NPBX （5 nm）/DPVBi （30 nm）/Alq（30 nm）/LiF（0.5 nm）/A1. In the devices, DPVBi acts as a blue light-emitting layer, the rubrene is sensitized by a phosphorescent material, fac tris （2-phenylpyridine） iridium [Ir（ppy）3], acts as a yellow light-emitting layer, and N,N＇ -bis- （1-naphthyl）- N,N＇ -diphenyl -1, 1＇ -biphenyl-4,4＇ -diamine （NPBX） acts as a hole transporting and exciton blocker layer, respectively. When the concentration of Ir （PPY）3 is 6wt%, the maximum luminance is 24960 cd/m^2 at an applied voltage of 15 V, and the maximum luminous efficiency is 5.17 cd/A at an applied voltage of 8 V.     

Complete approach to automatic identification and subpixel center location for ellipse feature

To meet the need of automatic image features extraction with high precision in visual inspection, a complete approach to automatic identification and sub-pixel center location for similar-ellipse feature is proposed. In the method, the feature area is identified automatically based on the edge attribute, and the sub-pixel center location is accomplished with the leastsquare algorithm. It shows that the method is valid, practical, and has high precision by experiment. Meanwhile this method can meet the need of instrumentation of visual inspection because of easy realization and without man-machine interaction.     

小角度扩展相关性近似算法分析

本论文提出一种在多天线MIMO信道相关性建模中小角度扩展近似理论算法,并应用于分析MIMO系统性能。分析中分别对三种不同角能量分布情况下的空间相关性研发快速近似计算法,并同时提出双模(Bi-Modal)角能量分布情况下的近似运算。通过分析这些新方法的近似效率,可以得到计算简单、复杂度低、而且符合实际的MIMO相关信道矩阵,对系统级的快速高效计算法的研究和系统级的评估以及误差分析具有重要的意义。     

Noise character analysis and the restraint of self-pulsation laser diodes

We calculate the Langevin noise sources of self-pulsation laser diodes, analyze the effects of active region noise and saturable-absorption region noise on the power fluctuation as well as period fluctuation, and propose a novel method to restrain the noise effects. A visible SIMULINK model is established to simulate the system, The results indicate that the effects of noise in absorption region can be ignored; that with the increase of DC injecting current, the noise effects enhance power jitter, and nevertheless, the period jitter is decreased; and that with external sinusoidal current modulating the self-pulsation laser diode, the noise-induced power jitter and period jitter can be suppressed greatly. This work is valuable for clock recovery in all-optical network.