CMOS兼容光电单片接收机的模拟与设计

设计了与CMOS工艺兼容的光电单片接收机电路,其中包括光电探测器、前置放大器和主放大器.它采用0.6μm CMOS工艺,可在自备的高阻外延片上使用MPW(multi-project wafer)进行流水.其中光电探测器的工作波长为850nm,响应度为0.2A/W,接收灵敏度为-16dBm,带宽为800MHz,因此适用于VSR(very short reach)系统.前置放大器采用电流模反馈放大器,主放大器输出为LVDS(low voltage differential signals)电平.通过器件模拟与电路模拟统一的方法将光电探测器与接收机放大电路进行统一模拟,分析了电路的限制因素,并提出了相应的改进方法.     

10Gb/s 0.18μm CMOS光接收机前端放大电路

介绍了利用TSMC 0.18μm CMON工艺设计的应用于SDH STM-64速率级(10Gb/s)光接收机前端放大电路。该电路由前置放大器和作为主放大器的限幅放大器构成,其中前置放大器采用RGC形式的互阻放大器实现,限幅放大器采用改进的Cherry—Hooper结构。模拟结果表明该电路可以工作在10Gb/s速率上。     

1Gb/s CMOS调节型共源共栅光接收机

基于特许0.35μm EEPROM CMOS标准工艺设计了一种单片集成光接收机芯片,集成了双光电探测器(DPD)、调节型共源共栅(RGC)跨阻前置放大器(TIA)、三级限幅放大器(LA,limiting amplifier)和输出电路,其中RGCTIA能够隔离光电二极管的电容影响,并可以有效地扩展光接收机的带宽。测试结果表明,光接收机的3dB带宽为821MHz,在误码率为10-9、灵敏度为-11dBm的条件下,光接收机的数据传输速率达到了1Gb/s;在3.3V电压下工作,芯片的功耗为54mW。     

高速12路并行CMOS单片光电集成接收机设计与实现

设计并实现了一个高速12路并行CMOS单片光电集成接收机.其每一路都包括一个光探测器、一个跨阻放大器以及后续放大电路.双光电二极管(DPD)结构可以提高接收机速度,但同时降低了响应度.在跨阻放大器电路中采用有源电感来展宽-3dB带宽.通过无锡上华(CSMC)0.6μm CMOS工艺流片并对芯片进行了测试.测试结果显示该接收机单路传输比特率可达0.8～1.4 Gb/s,总的12路可传输15Gb/s数据.     

与CMOS工艺兼容的硅高速光电探测器模拟与设计

用器件模拟的方法,设计了一种与常规CMOS 工艺兼容的硅高速光电探测器,该探测器可与CMOS接收机电路单片集成,对该探测器进行了器件模拟研究,给出了该探测器的电路模型.通过MOSIS(MOS implementation support project) 0.35μm COMS工艺制做了该探测器,实际测试了该器件的频率响应和波长响应,探测器频率响应在1GHz以上,峰值波长响应在0.69μm.     

高速12路并行CMOS单片光电集成接收机设计与实现

设计并实现了一个高速12路并行CMOS单片光电集成接收机.其每一路都包括一个光探测器、一个跨阻放大器以及后续放大电路.双光电二极管(DPD)结构可以提高接收机速度,但同时降低了响应度.在跨阻放大器电路中采用有源电感来展宽-3dB带宽.通过无锡上华(CSMC)0.6μm CMOS工艺流片并对芯片进行了测试.测试结果显示该接收机单路传输比特率可达0.8～1.4 Gb/s,总的12路可传输15Gb/s数据.     

与CMOS工艺兼容的硅高速光电探测器模拟与设计

用器件模拟的方法,设计了一种与常规CMOS 工艺兼容的硅高速光电探测器,该探测器可与CMOS接收机电路单片集成,对该探测器进行了器件模拟研究,给出了该探测器的电路模型.通过MOSIS(MOS implementation support project) 0.35μm COMS工艺制做了该探测器,实际测试了该器件的频率响应和波长响应,探测器频率响应在1GHz以上,峰值波长响应在0.69μm.     

基于APD的光电探测器电路研究与设计

提出将APD与前置放大器电路配合使用的最佳方法.利用光电转换信噪比数学模型,确定选择与APD匹配的电路器件,给出了前置放大器采用低噪声的分体器件与集成运算放大器相组合的设计方法.通过对前置放大器重要参数信噪比进行测量和分析.结果表明,该探测器电路信噪比优于直接与集成运算放大器匹配的探测器电路,且可靠性高,宜扩展,具有广泛的应用前景.     

CMOS单片光接收机的带宽设计

设计了一个由调节型级联跨阻抗放大器(TIA)和双光电二极管(DPD)构成的光电集成接收机.给出了DPD小信号电路模型和单片集成光接收机的带宽设计方法,给出限制DPD和光接收机带宽的重要因素,分析和模拟了这个光电集成接收机的带宽,用低成本的0.6μm CMOS工艺设计出1.71GHz带宽和49dB跨阻增益的接收机,并给出测试结果.     

瞬变光探测系统前置放大电路的设计

光电探测器前置放大电路设计的好坏会直接影响整个检测系统的信噪比.为了提高对微弱光信号的检测精度,使用低噪声光电二极管和运算放大器,并选择光电二极管工作在光伏模式,设计出了光电探测器的低噪声前置放大电路.通过采用超前校正方法对由光电二极管结电容及运算放大器输入电容引起的相移进行补偿,克服了光电二极管寄生参数引起的转换电路...     

Preparation and Characterization of TaN ALD Precursors

High purity organic-tantalum precursors for thin film ALD TaN were synthesized and characterized.Vapor pressure and thermal stability of these precursors were studied.From the vapor pressure analysis,it was found that TBTEMT has a higher vapor pressure than any other published liquid TaN precursor,including TBTDET,TAITMATA,and IPTDET.Thermal stability of the alkyl groups on the precursors was investigated using a 1H NMR technique.The results indicated that the tertbutylimino group is the most stable group on TBTDET and TBTEMT as compared to the dialkylamido groups.Thermal stability of TaN precursors decreased in the following order:TBTDET ＞ PDMAT ＞ TBTEMT.In conclusion,precursor vapor pressure and thermal stability were tuned by making slight variations in the ligand sphere around the metal center.     

Curved crystal spectrometer for the measurement of X-ray lines from laser-produced plasmas

In order to diagnose the laser-produced plasmas, a focusing curved crystal spectrometer has been developed for measuring the X-ray lines radiated from a laser-produced plasmas. The design is based on the fact that the ray emitted from a source located at one focus of an ellipse will converge on the other focus by the reflection of the elliptical surface. The focal length and the eccentricity of the ellipse are 1350 mm and 0.9586, respectively. The spectrometer can be used to measure the X- ray lines in the wavelength range of 0.2-0.37 nm, and a LiF crystal （200） （2d = 0.4027 nm） is used as dispersive element covering Bragg angle from 30° to 67.5°. The spectrometer was tested on Shengnang- Ⅱ which can deliver laser energy of 60-80 J/pulse and the laser wavelength is 0.35 μm. Photographs of spectra including the 1 s2p ^1P1-1s^2 ^1S0 resonance line（w）, the 1s2p ^3P2-1s^2 1S0 magnetic quadrupole line（x）, the 1s2p ^3P1-1 s^2 ^1S0 intercombination lines（y）, the 1 s2p ^3S~1-1 s^2 ^1S0 forbidden line（z） in helium-like Ti Ⅹ Ⅺ and the 1 s2s2p ^2P3/2-1 s622s ^2S1/2 line（q） in lithium-like Ti Ⅹ Ⅹhave been recorded with a X-ray CCD camera. The experimental result shows that the wavelength resolution（λ/△ 2） is above 1000 and the elliptical crystal spectrometer is suitable for X-ray spectroscopy.     

Electronic Structure of Semiconductor Nanocrystals

This paper reviews our recent development of the use of the large-scale pseudopotential method to calculate the electronic structure of semiconductor nanocrystals, such as quantum dots and wires, which often contain tens of thousands of atoms. The calculated size-dependent exciton energies and absorption spectra of quantum dots and wires are in good agreement with experiments. We show that the electronic structure of a nanocrystal can be tuned not only by its size,but also by its shape. Finally,we show that defect properties in quantum dots can be significantly different from those in bulk semiconductors.     

Critical Stage Rule-Based Real Time Dispatch（RTD）System in Highly-Mixed-Products （HMP） FAB

An improving utilization and efficiency of critical equipments in semiconductor wafer fabrication facilities are concerned. Semiconductor manufacturing FAB is one of the most complicated and cost sensitive environments. A good dispatching tool will make big difference in equipment utilization and FAB output as a whole. The equipment in this paper is In-Line DUV Scanner. There are many factors impacting utilization and output on this equipment group. In HMP environment one of the issues is changing of reticule in this area and idle counts due to load unbalance between equipments. Here we'll introduce a rule-based RTD system which aiming at decreasing the number of recipe change and idle counts among a group of scanner equipment in a high-mixed-products FAB.     

GaAsSb/InAlAs PA DHBTs Grown by Production MBE

The epi material growth of GaAsSb based DHBTs with InAlAs emitters are investigated using a 4 × 100mm multi-wafer production Riber 49 MBE reactor fully equipped with real-time in-situ sensors including an absorption band edge spectroscope and an optical-based flux monitor. The state-of-the-art hole mobilities are obtained from 100nm thick carbon-doped GaAsSb. A Sb composition variation of less than ± 0.1 atomic percent across a 4 × 100mm platen configuration has been achieved. The large area InAlAs/GaAsSb/InP DHBT device demonstrates excellent DC characteristics,such as BVCEO＞6V and a DC current gain of 45 at 1kA/cm2 for an emitter size of 50μm × 50μm. The devices have a 40nm thick GaAsSb base with p-doping of 4. 5 × 1019cm-3 . Devices with an emitter size of 4μm × 30μm have a current gain variation less than 2% across the fully processed 100mm wafer. ft and fmax are over 50GHz,with a power efficiency of 50% ,which are comparable to standard power GaAs HBT results. These results demonstrate the potential application of GaAsSb/InP DHBT for power amplifiers and the feasibility of multi-wafer MBE for mass production of GaAsSb-based HBTs.     

Noise character analysis and the restraint of self-pulsation laser diodes

We calculate the Langevin noise sources of self-pulsation laser diodes, analyze the effects of active region noise and saturable-absorption region noise on the power fluctuation as well as period fluctuation, and propose a novel method to restrain the noise effects. A visible SIMULINK model is established to simulate the system, The results indicate that the effects of noise in absorption region can be ignored; that with the increase of DC injecting current, the noise effects enhance power jitter, and nevertheless, the period jitter is decreased; and that with external sinusoidal current modulating the self-pulsation laser diode, the noise-induced power jitter and period jitter can be suppressed greatly. This work is valuable for clock recovery in all-optical network.     

High-quality single-crystal CdSe nanoribbons and their optical properties

Large-scale synthesis of single-crystal CdSe nanoribbons is achieved by a modified thermal evaporation method, in which two-step-thermal-evaporation is used to control CdSe sources＇ evaporation. The synthesized CdSe nanoribbons are usually several micrometers in width, 50 nm in thickness, and tens to several hundred micrometers in length. Studies have shown that high-quality CdSe nanoribbons with regular shapes can be obtained by this method. Room-temperature photolumines-cence indicates that the lasing emission at 710 nm has been observed under optical pumping （266 nm） at power densities of 25-153 kW/cm^2. The full width half maximum （FWHM） of the lasing mode is 0.67 nm     

Propagation of hermite-cosh-gaussian beams passing through ABCD optical system with an annular aperture

By using the expansion of the aperture function into a finte sum of complex Gaussian functions, the corresponding analytical expressions of Hermite-cosh-Gaussian beams passing through annular apertured paraxially and symmetrically optical systems written in terms of ABCD matrix were derived, and they could reduce to the cases with squared aperture. In a similar way, the corresponding analytical expressions of cosh-Gaussian beams through annular apertured ABCD matrix were also given. The method could save more calculation time than that by using the diffraction integral formula directly.     

Influence of polarization extinction ratio on distributed polarization coupling detection

Distributed polarization coupling in polarization-maintaining fibers can be detected by using a white light Michelson interferometer. This technique usually requires that only one polarization mode is excited. However, in practical measurement, the injection polarization direction could not be exactly aligned to one of the principal axes of the PMF, so the influence of the polarization extinction ratio should be considered. Based on the polarization coupling theory, the influence of the incident polarization extinction on the measurement result is evaluated and analyzed, and a method for distributed polarization coupling detection is developed when both two orthogonal eigenmodes are excited.     

Call for Papers

正Communications—VLSI Researches and industries of telecommunications have been growing rapidly in the last 20 years and will keep their high growing pace in the next decade.The involved researches and developments cover mobile communications,highway and last-mile broadband communication,domain specific communications,and emerging D2D M2M communications.Radio communication steps into its