薄p型层GaN基p-i-n型紫外探测器的反向漏电特性

制备了薄p型层GaN基p-i-n型紫外探测器,并对其反向漏电特性进行了研究。探测器材料采用金属有机化学气相沉积(MOCVD)方法在蓝宝石衬底上外延生长获得,p-GaN的厚度为30nm。基于该材料制作了具有共面电极的探测器器件,并采用SiO2对刻蚀侧壁进行了钝化。测试结果表明,结面积为1.825×10-4cm2的器件在-1V时的反向漏电流面密度为3.0×10-9 A/cm2,优质因子达到3.7×109Ω.cm2。     

利用ICPCVD方法在GaN上沉积氧化硅薄膜的特性

使用感应耦合等离子体化学气相沉积(Inductively coupled plasma chemical vapor deposition,ICPCVD)方法在GaN上沉积SiOx薄膜,生长参数中采用不同RF功率,研究RF功率对薄膜物理性能和电学性能的影响.结果发现,随着RF功率增大,薄膜应力增大,表面粗糙度减小,薄膜致密度增大.选择最优的RF功率参数,制作了SiOx/nGaN金属-绝缘体-半导体(metal-insulator-semiconductor,MIS)器件,结果得到薄膜漏电流密度在外加偏压为90V时小于1×10-7A/cm2,SiOx/n-GaN界面态密度为2.4×1010eV-1cm-2.表明利用ICPCVD低温沉积的SiOx-GaN界面态密度低,薄膜绝缘性能良好.     

GaN基肖特基结构紫外探测器

在蓝宝石(0001)衬底上采用低压金属有机物化学气相沉积(MOCVD)方法生长GaN外延层结构,以此为材料制作了GaN基肖特基结构紫外探测器.测量了该紫外探测器的暗电流曲线、C-V特性曲线、光响应曲线和响应时间曲线.该紫外探测器在5V偏压时暗电流为0.42nA,在10V偏压时暗电流为38.5nA.在零偏压下,该紫外探测器在250nm～365nm的波长范围内有较高的响应度,峰值响应度在363nm波长处达到0.12A/W,在365nm波长左右有陡峭的截止边;当波长超过紫外探测器的截止波长(365nm左右),探测器的响应度减小了三个数量级以上.该紫外探测器的响应时间小于2μs.     

介质膜性质及表面处理对GaN HEMT特性的影响

GaN HEMT器件经过钝化后,抑制电流崩塌效应明显,但同时产生其他负面效应,为了改善目前GaN HEMT钝化后漏电增加和击穿电压减小等情况,研究了钝化技术对GaN HEMT电流特性的影响,包括介质膜应力、折射率和表面预处理与器件饱和电流、电流崩塌量的关系,优化了表面预处理和钝化工艺条件.实验效果在CaN HEMT电特性上的改善明显.结果表明,采用折射率为2.1～2.2的SiN钝化膜,饱和电流密度增加到1 100 mA/mm,电流崩塌量小于10%,肖特基接触反向偏压为-20 V时泄漏电流达10-5A数量级.     

GaN基肖特基结构紫外探测器

在蓝宝石 (0 0 0 1)衬底上采用低压金属有机物化学气相沉积 (MOCVD)方法生长GaN外延层结构 ,以此为材料制作了GaN基肖特基结构紫外探测器 .测量了该紫外探测器的暗电流曲线、C V特性曲线、光响应曲线和响应时间曲线 .该紫外探测器在 5V偏压时暗电流为 0 4 2nA ,在 10V偏压时暗电流为 38 5nA .在零偏压下 ,该紫外探测器在2 5 0nm～ 36 5nm的波长范围内有较高的响应度 ,峰值响应度在 36 3nm波长处达到 0 12A/W ,在 36 5nm波长左右有陡峭的截止边 ;当波长超过紫外探测器的截止波长 (36 5nm左右 ) ,探测器的响应度减小了三个数量级以上 .该紫外探测器的响     

GaN基p-i-n型紫外探测器钝化工艺研究

钝化层膜系的选择及其工艺的优化对降低GaN基紫外探测器的漏电流和提升其可靠性是至关重要的。文章采用多种钝化层：等离子体增强化学气相沉积生长的Si₃N₄(PECVD-Si₃N₄)、电感耦合等离子体化学气相沉积生长的Si₃N₄(ICPCVD-Si₃N₄)和SiO₂(ICPCVD-SiO₂)以及等离子原子层沉积生长的Al₂O₃(PEALD-Al₂O₃),分别制备了GaN基金属-绝缘体-半导体(MIS)器件，并对MIS器件的电流-电压(I-V)和电容-电压(C-V)特性进行了对比研究。采用PECVD-Si₃N₄作为钝化层的GaN基MIS器件具有较低的漏电流；在双层PECVD-Si₃N₄钝化层中插入PEAL...     

AlInGaN/GaN PIN紫外光电探测器的研制

用AlInGaN四元合金代替AlGaN作为PIN探测器的有源层,研制出AlInGaNPIN紫外探测器.详细介绍了该器件的结构设计和制作工艺,并对器件进行了光电性能测试.测试结果表明,器件的正向开启电压约为1.5 V,反向击穿电压大于40 V;室温-5 V偏压下,暗电流为33 pA,350 nm处峰值响应度为0.163 A/W,量子效率为58%.     

一维阵列MSM 4H-SiC紫外光电探测器的研制

采用Ni/Au作为肖特基接触制备了一维阵列MSM 4H-SiC紫外光电探测器,并测量和分析了阵列器件的Ⅰ-Ⅴ、光谱响应特性.结果表明,阵列探测器性能均匀性好,击穿电压均高于100V.阵列中单器件暗电流小,在偏压为20V的时候,最大暗电流均小于5pA(电流密度为5nA/cm2),光电流比暗电流高3个数量级以上.其光谱响应表明,单器件在电压为20V时的响应度约为0.09A/W,比400nm时的比值均大5000倍,说明探测器具有良好的紫外可见比.     

基于斜台面工艺的背照式GaN雪崩探测器制备

对基于斜台面工艺的背照式pin型GaN紫外雪崩探测器制备进行了简要介绍.通过斜台面制作工艺的对比优化研究,完成了GaN紫外雪崩探测器的低损伤斜台面制作,器件测试结果表明,高质量斜台面能够有效抑制雪崩探测器的表面提前击穿,器件暗电流特性优良,获得了超高雪崩增益的GaN紫外雪崩探测器.     

SiO_2钝化层对GaN基PIN结构核探测器漏电流的影响

成功地制备了有SiO2钝化层和无SiO2钝化层的GaN基PIN结构核辐射探测器,并对二者的I-V特性进行了测试。实验结果表明,SiO2钝化层的存在显著地降低了GaN基PIN结构核辐射探测器的反向漏电流,在-40V的反向偏压情况下,漏电流约有2个数量级的降低。实验过程中观测到随着反向偏压的增大,SiO2钝化层对器件反向漏电流的抑制效应更明显。建立了一种表面沟道模型解释了SiO2钝化层对漏电流的影响。     

Technology innovation and process integrations for sub-100nm gate patterning

This paper presents a brief overview of the Applied Centura(R)DPS(R)system,configured with silicon etch DPS Ⅱ chamber, with emphasis on discussing tuning capability for CD uniformity control. It also presents the studies of etch process chemistry and film integration impact for an overall successful gate patterning development. Discussions will focus on resolutions to key issues, such as CD uniformity, line-edge roughness, and multilayer film etching integration.     

White organic light-emitting devices based on fac tris（2- phenylpyridine） iridium sensitized 5,6,11,12-tetraphenylnap -hthacene

We have fabricated the white organic light-emitting devices （WOLEDs） based on 4,4＇ -bis（2,2 -diphenyl vinyl）-1,1＇ - biphenyl （DPVBi） and phosphorescence sensitized 5,6,11,12,-tetraphenylnaphthacene （rubrene）. The device structure is ITO/2T-NATA （20 nm）/NPBX （20 nm）/CBP： x%Ir（ppy）3：0.5% rubrene （8 nm）/NPBX （5 nm）/DPVBi （30 nm）/Alq（30 nm）/LiF（0.5 nm）/A1. In the devices, DPVBi acts as a blue light-emitting layer, the rubrene is sensitized by a phosphorescent material, fac tris （2-phenylpyridine） iridium [Ir（ppy）3], acts as a yellow light-emitting layer, and N,N＇ -bis- （1-naphthyl）- N,N＇ -diphenyl -1, 1＇ -biphenyl-4,4＇ -diamine （NPBX） acts as a hole transporting and exciton blocker layer, respectively. When the concentration of Ir （PPY）3 is 6wt%, the maximum luminance is 24960 cd/m^2 at an applied voltage of 15 V, and the maximum luminous efficiency is 5.17 cd/A at an applied voltage of 8 V.     

Complete approach to automatic identification and subpixel center location for ellipse feature

To meet the need of automatic image features extraction with high precision in visual inspection, a complete approach to automatic identification and sub-pixel center location for similar-ellipse feature is proposed. In the method, the feature area is identified automatically based on the edge attribute, and the sub-pixel center location is accomplished with the leastsquare algorithm. It shows that the method is valid, practical, and has high precision by experiment. Meanwhile this method can meet the need of instrumentation of visual inspection because of easy realization and without man-machine interaction.     

小角度扩展相关性近似算法分析

本论文提出一种在多天线MIMO信道相关性建模中小角度扩展近似理论算法,并应用于分析MIMO系统性能。分析中分别对三种不同角能量分布情况下的空间相关性研发快速近似计算法,并同时提出双模(Bi-Modal)角能量分布情况下的近似运算。通过分析这些新方法的近似效率,可以得到计算简单、复杂度低、而且符合实际的MIMO相关信道矩阵,对系统级的快速高效计算法的研究和系统级的评估以及误差分析具有重要的意义。     

Curved crystal spectrometer for the measurement of X-ray lines from laser-produced plasmas

In order to diagnose the laser-produced plasmas, a focusing curved crystal spectrometer has been developed for measuring the X-ray lines radiated from a laser-produced plasmas. The design is based on the fact that the ray emitted from a source located at one focus of an ellipse will converge on the other focus by the reflection of the elliptical surface. The focal length and the eccentricity of the ellipse are 1350 mm and 0.9586, respectively. The spectrometer can be used to measure the X- ray lines in the wavelength range of 0.2-0.37 nm, and a LiF crystal （200） （2d = 0.4027 nm） is used as dispersive element covering Bragg angle from 30° to 67.5°. The spectrometer was tested on Shengnang- Ⅱ which can deliver laser energy of 60-80 J/pulse and the laser wavelength is 0.35 μm. Photographs of spectra including the 1 s2p ^1P1-1s^2 ^1S0 resonance line（w）, the 1s2p ^3P2-1s^2 1S0 magnetic quadrupole line（x）, the 1s2p ^3P1-1 s^2 ^1S0 intercombination lines（y）, the 1 s2p ^3S~1-1 s^2 ^1S0 forbidden line（z） in helium-like Ti Ⅹ Ⅺ and the 1 s2s2p ^2P3/2-1 s622s ^2S1/2 line（q） in lithium-like Ti Ⅹ Ⅹhave been recorded with a X-ray CCD camera. The experimental result shows that the wavelength resolution（λ/△ 2） is above 1000 and the elliptical crystal spectrometer is suitable for X-ray spectroscopy.     

Preparation and Characterization of TaN ALD Precursors

High purity organic-tantalum precursors for thin film ALD TaN were synthesized and characterized.Vapor pressure and thermal stability of these precursors were studied.From the vapor pressure analysis,it was found that TBTEMT has a higher vapor pressure than any other published liquid TaN precursor,including TBTDET,TAITMATA,and IPTDET.Thermal stability of the alkyl groups on the precursors was investigated using a 1H NMR technique.The results indicated that the tertbutylimino group is the most stable group on TBTDET and TBTEMT as compared to the dialkylamido groups.Thermal stability of TaN precursors decreased in the following order:TBTDET ＞ PDMAT ＞ TBTEMT.In conclusion,precursor vapor pressure and thermal stability were tuned by making slight variations in the ligand sphere around the metal center.     

A Versatile Mixed-Signal Pin Approach for Cost-Effective Test of Automotive ICs

Integrated circuits (ICs) intended for increasingly sophisticated automotive applications bring unique test demands. Advanced ICs for applications such as highly integrated automatic braking system (ABS) and airbag controllers combine high voltage digital channels, significant VI demands and precise timing capability. Along with continued missioncritical reliability concerns, the trend toward higher voltage operation and increased device integration requires specialized test capabilities able to extend across the wide operating ranges found in automotive applications. Among these capabilities, automotive test requirements increasingly dictate a need for a cost-effective versatile mixed-signal pin electronics with very high data rates reaching up to 50MHz with a voltage swing of-2 V to +28 V.     

Electronic Structure of Semiconductor Nanocrystals

This paper reviews our recent development of the use of the large-scale pseudopotential method to calculate the electronic structure of semiconductor nanocrystals, such as quantum dots and wires, which often contain tens of thousands of atoms. The calculated size-dependent exciton energies and absorption spectra of quantum dots and wires are in good agreement with experiments. We show that the electronic structure of a nanocrystal can be tuned not only by its size,but also by its shape. Finally,we show that defect properties in quantum dots can be significantly different from those in bulk semiconductors.     

Critical Stage Rule-Based Real Time Dispatch（RTD）System in Highly-Mixed-Products （HMP） FAB

An improving utilization and efficiency of critical equipments in semiconductor wafer fabrication facilities are concerned. Semiconductor manufacturing FAB is one of the most complicated and cost sensitive environments. A good dispatching tool will make big difference in equipment utilization and FAB output as a whole. The equipment in this paper is In-Line DUV Scanner. There are many factors impacting utilization and output on this equipment group. In HMP environment one of the issues is changing of reticule in this area and idle counts due to load unbalance between equipments. Here we'll introduce a rule-based RTD system which aiming at decreasing the number of recipe change and idle counts among a group of scanner equipment in a high-mixed-products FAB.     

Optical vibration and deviation measurement of rotating machine parts

It is of interest to get appropriate information about the dynamic behaviour of rotating machinery parts in service. This paper presents an approach of optical vibration and deviation measurement of such parts. Essential of this method is an image derotator combined with a high speed camera or a laser doppler vibrometer （LDV）.