Hg_(0.8)Cd_(0.2)Te液相外延的优质衬底——Cd_(1-x)Zn_xTe的晶体生长及应用

用改进型垂直布里奇曼法(VMB)生长出的Cd_(1-x)Zn_xTe (X=0.04)梨晶,切成具有单晶的薄片面积大达10～12cm~2,本文还对它代替CdTe用作液相外延生长HgCdTe的衬底,作了评价。与典型的CdTe晶体相比,CdZnTe晶体的缺陷密度较低、机械强度较好,并大大改善了在CdZnTe上生长的HgCdTe液相外延层的宏观与微观形态。CdZnTe衬底上生长的液相外延层的表面形貌表明,它与取向的关系,比在CdTe衬底(取向接近于{111}的平面)上生长的外延层与取向的关系更小。Zn加到CdTe晶格中可以使共价性增加,离子性降低,这样就抑制了范性形变和位错的产生。这些因素的组合能把晶格常数调整到两个极值范围内的任何所需要的值,这样就可以生长高性能红外探测器阵列所要求的低缺陷密度的HgCdTe外延层。通过缺陷腐蚀、红外显微镜检查、X射线摆动曲线分析和X射线形貌测量,对衬底和外延层的质量作了评定。     

HWE 生长大面积CdTe/ CdZnTe/ Si 薄膜的结构和形貌分析

用热壁外延法(HWE) 生长直径30mm 的CdTe/ CdZnTe/ Si 薄膜,经XRD 测试说明它是 晶面为(111) 取向的立方闪锌矿结构。SEM对Si 衬底、CdZnTe 缓冲层和CdTe 薄膜三层分别测试,结果发现: Si 衬底表面结构粗糙,CdZnTe 缓冲层较Si 衬底表面结构细致,CdTe 薄膜较CdZnTe 缓冲层表面结构光滑细密,即缺陷较CdZnTe 缓冲层少很多。通过对该片子照像看出其表面如镜面。由此说明大面积CdTe/ CdZnTe/ Si 薄膜可用HWE 技术制备。     

HWE 生长大面积CdTe/ CdZnTe/ Si 薄膜的结构和形貌分析

用热壁外延法(HWE)生长直径30mm的CdTe／CdZnTe／Si薄膜，经XRD测试说明它是晶面为(111)取向的立方闪锌矿结构。SEM对Si衬底、CdZnTe缓冲层和CdTe薄膜三层分别测试，结果发现：Si衬底表面结构粗糙，CdZnTe缓冲层较Si衬底表面结构细致，CdTe薄膜较CdZnTe缓冲层表面结构光滑细密，即缺陷较CdZnTe缓冲层少很多。通过对该片子照像看出其表面如镜面。由此说明大面积CdTe／CdZnTe／Si薄膜可用HWE技术制备。     

多层HgCdTe异质外延材料的热退火应力分析

前期研究采用高温热处理方法,获得了抑制位错的最佳退火条件.通过比对实验,发现不同衬底上HgCdTe表面的CdTe钝化层在热处理过程中对位错的抑制作用各有不同.结合晶格失配应力和热应力对不同异质结构进行理论计算,借助X射线摇摆曲线的倒易空间分析,解释了CdTe钝化层对HgCdTe位错抑制的影响作用.     

CdTe、CdZnTe性能改善

去年这个时候，美国二六公司报道用CdZnTe代替CdTe作红外探测器。今年宾夕法尼亚州Saxonburg公司说，现在人们对用生长在透红外光CdTe和CdZnTe化合物上的外延结构来研制焦平面列阵探测器，仍有很浓的兴趣。     

分子束外延的CdTe在碲镉汞中波器件中钝化效果

采用分子束外延技术（MBE）制备了碲化镉（CdTe）原位钝化的中波碲镉汞（HgCdTe）材料。原子力显微镜（AFM）和扫描电子显微镜（SEM）测试结果表明,分子束原位外延的CdTe可见cross-hatch,表面粗糙度为1～2 nm,CdTe和HgCdTe界面结合紧密。微波光导测试结果显示,77 K时,与表面处理后非原位CdTe钝化的HgCdTe材料相比,CdTe原位钝化的HgCdTe材料的少子寿命较大。制备了分子束外延CdTe原位钝化的中波HgCdTe光伏器件,和相同材料上的非原位CdTe/ZnS双层钝化制备的器件I-V特性相似。     

HgCdTe红外探测器CdTe钝化蒸发生长改进

在液相外延生长(LPE)的碲镉汞(HgCdTe)外延薄膜(111)方向上蒸发生长碲化镉(CdTe)钝化层。在70～250℃范围内的各个不同的温度环境下进行碲化镉钝化膜的蒸发生长。根据需要,对各样本进行150～300℃各个温度下的后期退火处理。运用扫描电镜(SEM)、透射电镜(TEM)、二次离子质谱(SIMS)、X射线衍射(XRD)观测技术表征碲化镉钝化膜的形貌结构、成分分布、晶体质量。结果表明,加热环境下蒸发生长碲化镉钝化膜可以消除常规蒸发生长中的柱状多晶结构,显著提高钝化品质;后期的退火处理还能进一步提高钝化膜质量。     

CdTe/ZnS双层钝化碲镉汞长波探测器制备的研究

开展了CdTe/ZnS双层钝化碲镉汞长波探测器制备的研究。CdTe钝化膜经退火热处理后,可实现CdTe/MCT界面的互扩散,并改善CdTe钝化膜的质量。通过全湿法腐蚀方法完成了金属化开口,制备了长波碲镉汞600×18@15 μm规格线列和640×512@15 μm规格面阵。线列I-V测试表明:CdTe/ZnS双层钝化膜能有效地减少长波碲镉汞器件的表面漏电流,器件的反向结特性良好。面阵在77K测试:NETD 26.7 mK,有效像元率95.4%,并对室温目标进行了凝视成像。测试过程出现了4%左右由噪声引起的零散盲元,是由芯片面阵局部钝化失效引起的,表明钝化膜沉积工艺及芯片加工工艺尚有改进的空间。     

CdTe/ZnS复合钝化层对长波碲镉汞器件性能的影响研究

采用CdTe/ZnS复合钝化技术对长波HgCdTe薄膜进行表面钝化,并对钝化膜生长工艺进行了改进。采用不同钝化工艺分别制备了MIS器件和二极管器件,并进行了SEM、C-V和I-V表征分析,研究了HgCdTe/钝化层之间的界面特性及其对器件性能的影响。结果表明,钝化工艺改进后所生长的CdTe薄膜更为致密且无大的孔洞,CdTe/HgCdTe界面晶格结构有序度获得改善;采用改进的钝化工艺制备的MIS器件C-V测试曲线呈现高频特性,界面固定电荷面密度从改进前的1.671011 cm-2下降至5.691010 cm-2;采用常规钝化工艺制备的二极管器件在较高反向偏压下出现较大的表面沟道漏电流,新工艺制备的器件表面漏电现象获得了有效抑制。     

不同钝化结构的HgCdTe光伏探测器暗电流机制

在同一HgCdTe晶片上制备了单层ZnS钝化和双层（CdTe+ZnS）钝化的两种光伏探测器,对器件的性能进行了测试,发现双层钝化的器件具有较好的性能．通过理论计算,分析了器件的暗电流机制,发现单层钝化具有较高的表面隧道电流．通过高分辨X射线衍射中的倒易点阵技术研究了单双层钝化对HgCdTe外延层晶格完整性的影响,发现单层ZnS钝化的HgCdTe外延层产生了大量缺陷,而这些缺陷正是单层钝化器件具有较高表面隧道电流的原因．     

Preparation and Characterization of TaN ALD Precursors

High purity organic-tantalum precursors for thin film ALD TaN were synthesized and characterized.Vapor pressure and thermal stability of these precursors were studied.From the vapor pressure analysis,it was found that TBTEMT has a higher vapor pressure than any other published liquid TaN precursor,including TBTDET,TAITMATA,and IPTDET.Thermal stability of the alkyl groups on the precursors was investigated using a 1H NMR technique.The results indicated that the tertbutylimino group is the most stable group on TBTDET and TBTEMT as compared to the dialkylamido groups.Thermal stability of TaN precursors decreased in the following order:TBTDET ＞ PDMAT ＞ TBTEMT.In conclusion,precursor vapor pressure and thermal stability were tuned by making slight variations in the ligand sphere around the metal center.     

Curved crystal spectrometer for the measurement of X-ray lines from laser-produced plasmas

In order to diagnose the laser-produced plasmas, a focusing curved crystal spectrometer has been developed for measuring the X-ray lines radiated from a laser-produced plasmas. The design is based on the fact that the ray emitted from a source located at one focus of an ellipse will converge on the other focus by the reflection of the elliptical surface. The focal length and the eccentricity of the ellipse are 1350 mm and 0.9586, respectively. The spectrometer can be used to measure the X- ray lines in the wavelength range of 0.2-0.37 nm, and a LiF crystal （200） （2d = 0.4027 nm） is used as dispersive element covering Bragg angle from 30° to 67.5°. The spectrometer was tested on Shengnang- Ⅱ which can deliver laser energy of 60-80 J/pulse and the laser wavelength is 0.35 μm. Photographs of spectra including the 1 s2p ^1P1-1s^2 ^1S0 resonance line（w）, the 1s2p ^3P2-1s^2 1S0 magnetic quadrupole line（x）, the 1s2p ^3P1-1 s^2 ^1S0 intercombination lines（y）, the 1 s2p ^3S~1-1 s^2 ^1S0 forbidden line（z） in helium-like Ti Ⅹ Ⅺ and the 1 s2s2p ^2P3/2-1 s622s ^2S1/2 line（q） in lithium-like Ti Ⅹ Ⅹhave been recorded with a X-ray CCD camera. The experimental result shows that the wavelength resolution（λ/△ 2） is above 1000 and the elliptical crystal spectrometer is suitable for X-ray spectroscopy.     

Cost-effective test solutions for smart card and other integrated flash applications

From its emergence in the late 1980s as a lower cost alternative to early EEPROM technologies, flash memory has evolved to higher densities and speedsand rapidly growing acceptance in mobile applications.In the process, flash memory devices have placed increased test requirements on manufacturers. Today, as flash device test grows in importance in China, manufacturers face growing pressure for reduced cost-oftest, increased throughput and greater return on investment for test equipment. At the same time, the move to integrated flash packages for contactless smart card applications adds a significant further challenge to manufacturers seeking rapid, low-cost test.     

An improved parallel thinning algorithm with two subiterations

The parallel thinning algorithm with two subiterations is improved in this paper. By analyzing the notions of connected components and passes, a conclusion is drawn that the number of passes and the number of eight-connected components are equal. Then the expression of the number of eight-connected components is obtained which replaces the old one in the algorithm. And a reserving condition is proposed by experiments, which alleviates the excess deletion where a diagonal line and a beeline intersect. The experimental results demonstrate that the thinned curve is almost located in the middle of the original curve connectivelv with single pixel width and the processing speed is high.     

Theoretical analysis of the relationship between the Brillouin gain coefficient and the strain in the optical-fiber sensors

The relation between the power of the Brillouin signal and the strain is one of the bases of the distributed fiber sensors of temperature and strain. The coefficient of the Bfillouin gain can be changed by the temperature and the strain that will affect the power of the Brillouin scattering. The relation between the change of the Brillouin gain coefficient and the strain is thought to be linear by many researchers. However, it is not always linear based on the theoretical analysis and numerical simulation. Therefore, errors will be caused if the relation between the change of the Brillouin gain coefficient and the strain is regarded as to be linear approximately for measuring the temperature and the strain. For this reason, the influence of the parameters on the Brillouin gain coefficient is proposed through theoretical analysis and numerical simulation.     

Novel fiber-optical interferometer with miniaturized probe for in-hole measurements

Today, micro-system technology and the development of new MEMS （Micro-Electro-Mechanical Systems） are emerging rapidly. In order for this development to become a success in the long run, measurement systems have to ensure product quality. Most often, MEMS have to be tested by means of functionality or destructive tests. One reason for this is that there are no suitable systems or sensing probes available which can be used for the measurement of quasi inaccessible features like small holes or cavities. We present a measurement system that could be used for these kinds of measurements. The system combines a fiber optical, miniaturized sensing probe with low-coherence interferometry, so that absolute distance measurements with nanometer accuracy are possible.     

Electronic Structure of Semiconductor Nanocrystals

This paper reviews our recent development of the use of the large-scale pseudopotential method to calculate the electronic structure of semiconductor nanocrystals, such as quantum dots and wires, which often contain tens of thousands of atoms. The calculated size-dependent exciton energies and absorption spectra of quantum dots and wires are in good agreement with experiments. We show that the electronic structure of a nanocrystal can be tuned not only by its size,but also by its shape. Finally,we show that defect properties in quantum dots can be significantly different from those in bulk semiconductors.     

Critical Stage Rule-Based Real Time Dispatch（RTD）System in Highly-Mixed-Products （HMP） FAB

An improving utilization and efficiency of critical equipments in semiconductor wafer fabrication facilities are concerned. Semiconductor manufacturing FAB is one of the most complicated and cost sensitive environments. A good dispatching tool will make big difference in equipment utilization and FAB output as a whole. The equipment in this paper is In-Line DUV Scanner. There are many factors impacting utilization and output on this equipment group. In HMP environment one of the issues is changing of reticule in this area and idle counts due to load unbalance between equipments. Here we'll introduce a rule-based RTD system which aiming at decreasing the number of recipe change and idle counts among a group of scanner equipment in a high-mixed-products FAB.     

GaAsSb/InAlAs PA DHBTs Grown by Production MBE

The epi material growth of GaAsSb based DHBTs with InAlAs emitters are investigated using a 4 × 100mm multi-wafer production Riber 49 MBE reactor fully equipped with real-time in-situ sensors including an absorption band edge spectroscope and an optical-based flux monitor. The state-of-the-art hole mobilities are obtained from 100nm thick carbon-doped GaAsSb. A Sb composition variation of less than ± 0.1 atomic percent across a 4 × 100mm platen configuration has been achieved. The large area InAlAs/GaAsSb/InP DHBT device demonstrates excellent DC characteristics,such as BVCEO＞6V and a DC current gain of 45 at 1kA/cm2 for an emitter size of 50μm × 50μm. The devices have a 40nm thick GaAsSb base with p-doping of 4. 5 × 1019cm-3 . Devices with an emitter size of 4μm × 30μm have a current gain variation less than 2% across the fully processed 100mm wafer. ft and fmax are over 50GHz,with a power efficiency of 50% ,which are comparable to standard power GaAs HBT results. These results demonstrate the potential application of GaAsSb/InP DHBT for power amplifiers and the feasibility of multi-wafer MBE for mass production of GaAsSb-based HBTs.     

Teleportation of an arbitrary unknown N-qubit entangled state under the controlling of M controllers

A new quantum protocol to teleport an arbitrary unknown N-qubit entangled state from a sender to a fixed receiver under M controllers(M < N) is proposed. The quantum resources required are M non-maximally entangled Greenberger-Home-Zeilinger (GHZ) state and N-M non-maximally entangled Einstein-Podolsky-Rosen (EPR) pairs. The sender performs N generalized Bell-state measurements on the 2N particles. Controllers take M single-particle measurement along x-axis, and the receiver needs to introduce one auxiliary two-level particle to extract quantum information probabilistically with the fidelity unit if controllers cooperate with it.