共查询到18条相似文献,搜索用时 199 毫秒
1.
3.
4.
5.
6.
7.
考察妥尔油改性酚醛补强树脂SL-2101和腰果油改性酚醛补强树脂SL-2201对全钢载重子午线轮胎三角胶性能的影响。结果表明:与补强树脂SL-2101相比,补强树脂2201对胶料的补强性能好;随着2种补强树脂用量增大,胶料物理性能提高;采用补强树脂SL-2201替代补强树脂SL-2101,需适当调整硫化体系。 相似文献
8.
9.
10.
11.
12.
Resole phenolic resins containing various p-cresol (PC) to phenol (P) mol ratios were prepared and characterized. These phenolic resins were blended with nitrile rubber (NBR) and the measurements of adhesive joint strength, stress–strain properties, DSC, TGA, DMA, TEM, and SEM were performed using a 50 : 50 NBR/phenolic resin blend. It was observed that the adhesive joint strength and the mechanical properties of the blend enhanced significantly on incorporation of p-cresol into the phenolic resin, and the optimum p-cresol/phenol mol ratio was in the vicinity of 2 : 1. Observation of a more continuous phase and the increase in Tg of the rubber region in the blend indicated increased reactivity and compatibilization of NBR with phenolic resin as p-cresol was incorporated. The effect of silica filler on the properties of the nitrile rubber/phenolic resin blend was also studied without and with p-cresol modification and the results suggest that silica filler take not only the role of a reinforcing filler in the nitrile–phenolic–silica composite, but also a role as surface compatibilizer of the blend components. © 1998 John Wiley & Sons, Inc. J Appl Polym Sci 69: 1187–1201, 1998 相似文献
13.
对酚醛树脂在轮胎中的应用进行了回顾和展望。在轮胎生产中,酚醛树脂是重要的原材料之一。酚醛树脂具有优异的物理性能以及丰富的反应官能团,在轮胎生产过程中可起到增粘、补强、粘合以及交联等作用。随着轮胎生产技术和材料研发水平的不断提高,酚醛树脂生产企业应顺应时代潮流,不断开发性能更优异、更环保的产品,以满足高性能轮胎生产要求。 相似文献
14.
研究补强树脂间苯二酚SL-R80/六甲氧基甲基三聚氰胺树脂(HMMM)、间苯二酚-甲醛树脂SL-3020LFR/HMMM、酚醛树脂SL-2101/六亚甲基四胺(HMT)和高苯乙烯树脂S-6-H在全钢轮胎中的应用。结果表明:4种补强树脂对胶料的硫化均有延缓作用,其中采用SL-R80/HMMM的胶料t90最长,采用SL-2101/HMT的胶料t90最短;与空白胶料相比,只有采用S-6-H的胶料的t5延长,其余胶料均缩短;采用SL-3020LFR/HMMM的胶料加工流动性变差,其余胶料变化不大;4种补强树脂均能有效提高胶料硬度,其中SL-R80/HMMM的提高效果最佳;4种补强树脂对胶料的拉伸强度和拉断伸长率的影响都很小,但对撕裂强度有负面影响,其中SL-R80/HMMM的影响最大,SL-3020LFR/HMMM的影响最小;S-6-H树脂对胶料的生热基本没有影响,其他3种树脂均有负面影响,其中SL-3020LFR/HMMM的影响最大。 相似文献
15.
Preparation and properties of styrene‐butadiene rubber nanocomposites blended with carbon black‐graphene hybrid filler 下载免费PDF全文
Graphene has become an attractive reinforcing filler for rubber materials, but its dispersion in rubber is still a big challenge. In this work, a novel carbon black‐reduced graphene (CB‐RG) hybrid filler was fabricated and blended with styrene‐butadiene rubber (SBR) via simple two‐roll mill mixing. The prepared CB‐RG hybrids had a microstructure with small CB agglomerates adsorbed onto graphene surfaces. CB acted as a barrier preventing the RG sheets from restacking even after drying. Homogeneous dispersion of graphene sheets in SBR matrix was observed by the mechanical mixing method based on the application of the CB‐RG hybrid fillers. Dynamic mechanical analysis showed that Tg of the SBR/CB‐RG blend was higher than that of the SBR/CB blend indicating strong interfacial interactions between RG and SBR due to the high surface area of graphene and the π‐π interaction between SBR and graphene. The tensile properties of SBR/CB‐RG composites improved significantly and the volume resistivity decreased compared with the SBR/CB blends. The thermal stability of SBR composites filled with CB and CB‐RG showed slight difference. © 2014 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2015 , 132, 41309. 相似文献
16.
试验研究低软化点204树脂在全钢子午线轮胎三角胶中的应用。结果表明,以低软化点204树脂等量替代高软化点204树脂后,胶料的硫化特性基本一致,硫化胶的邵尔A型硬度略低,100%和300%定伸应力、拉伸强度及拉断伸长率均有所提高,胶料的粘性提高。 相似文献
17.
18.
对载重斜交轮胎胎圈钢丝包胶配方进行优化。试验结果表明:在胎圈钢丝包胶中加入粘合剂RH和硼酰化钴,增大补强填充剂和芳烃油的用量,并对配方进行适当调整,胶料强度虽有所降低,但与胎圈钢丝的粘合性能明显提高,成品轮胎胎圈质量改善,生产成本降低。 相似文献