Effect of Permeable Crystalline Material on Steel Reinforcement Corrosion of Concrete

Permeable crystalline materialcan permeate into pores and cracks of concrete and catalyze the reaction between Ca(OH) 2and unhydrated cement to generate a great quantity needle non-soluble crystals, which can stop up the pores and cracks of concrete, and increase the impermeability of concrete. This paper reported the results of a study conducted to evaluate steel reinforcement corrosion of concrete specimens uncoated and coated with permeable crystalline material as well as mixed with the permeable crystalline material. The properties evaluated for corrosion test were water impermeability, water absorption, compressive strength and potential. The results of water impermeability, water absorption, compressive strength clearly showed that the permeable crystalline material could prohibit water, any soluble salts and moisture from penetrating the concrete to cause corrosion, leaking, and other problems, and it did increase the compressive strength, which was favorable for protection of corrosion of reinforcing steel. Moreover, it was concluded from the potential-time curve that the steel reinforcement of uncoated specimen was in the state of activation whereas that of other specimens coated and mixed with the permeable crystalline material was in the state of inactivation. Above all, it was indicated that the permeable crystalline materialis very effective to protect the steel reinforcement of concrete from corrosion.     

The Research and Application About "Dry Peeling Off" Technology for Airplane Surface Paint Layer

In this paper, the principle of spurting take off lacquer were introduced; and with orthogonal method the unsaturate polyester was prepared ;it was easy to peel airplane paint layer off with this material and equipment.     

Quality Study of Honeycomb Core Shaping Without Wax Stabilization

Sandwich panels utilizing honeycomb cores result in lightweight, high-strength units that are very rigid. Indeed, they give honeycomb panels the best strength-to-weight ratio of any construction type available. Conventionally, the wax is poured into the cell of the core to strengthen the structure and prevent the core from being crushed during milling. Much time and labor is required to wax, mill, and clean the cores. In this study, the process of pouring wax into the core was skipped. In other words, the cutter directly milled the core. Experiments showed that the compressive strength of the core produced without wax stabilization was only 3% lower than that of cores produced using the traditional method. In addition, the drum peel strengths of cores produced without wax stabilization were 38.4% higher than cores produced using the traditional method, in which residual wax seriously polluted the adhesive. It was also found that eliminating the wax process can reduce costs.     

In-process thermal treatment of polylactic acid in fused deposition modelling

Polylactic acid (PLA) is one of the most widely used open source fused filament fabrication materials due to its ease of extrusion, biodegradability, and mechanical strength. The mechanical strength of PLA largely depends on the proper growth of its semi-crystalline structure, which can be severely impaired by a low rate of crystallization, particularly in open source printers. This can be further aggravated by the non-uniform thermal distribution of heat that causes improper curing among the extruded beads of the printing material. As a result, PLA printed on open source printers does not achieve the best mechanical properties. This research, for the first time, proposes an additive-free solution implemented through a detailed set of experimentation to improve the curing rate through in-process temperature variations to cure the joints among the beads. Scanning electron microscopy (SEM), differential scanning calorimetry (DSC) and Fourier transform infrared (FTIR) spectroscopy is used to confirm the improvements in the bead joints. This work is conducted in two phases of experiments. In the first phase, a full factorial ANOVA is used to investigate various process parameters and the important variables are used in the second phase to print test specimens in four different sets.     

Investigation of the Corrosion Behaviors of HVOF-Sprayed Carbide Cernet Coatings in Molten Al-Zn-Si Alloy Bath

In continuous hot-dip galvanization process the corrosion and chemical stability of the sink roll in the galvanizing bath are important problem which effects on the quality and productivity. In order to protect the sink roll the carbide cermet and/or ceramic coatings were deposited on the surface of the sink roll. The WC-, Cr3 C2-cermet coatings were deposited by high velocity oxygen fuel (HVOF) spray, respectively. The coating samples were immersed in molten Zn-alloy containing 50 wt % aluminum at 833 K for 24 hr and 144 hr, respectively. The inter-diffusion and inter-reaction of Zn, Al and elements in coating and corrosion behaviors of these coatings were investigated by XRD, SEM and EPMA etc. The corrosion mechanisms of the carbide cermet coatings and ceramic coatings in molten High Al-Zn-alloy were approached.     

Fundamental study of adhesion of ice to cooling solid surface (Discussion on influence of copper oxide layer on ice adhesion force)

In many situations, ice often adheres to a cooling solid surface, frequently causing serious accidents. It is critical to clarify the mechanism of ice adhesion to the cooling surface in order to prevent ice adhesion. In a past study, the shearing stresses of two kinds of test plates with a copper surface having the higher thermal conductivity were measured. The shearing stress corresponds to ice adhesion force. Both shearing stresses were significantly different; however, the cause remains unclear.Therefore, the present study focuses on an oxide layer as the main factor causing the difference of both shearing stresses; the influence of the oxide layer formed on shearing stress was discussed. And in the removal and reformation processes of the oxide layer, the time variation of the shearing stress was clarified. Moreover, the relationship between the state of the copper surface and the shearing stress was also clarified by surface analysis.     

＂Three Transformations＂ and Standardization

During his inspection in Henan Province in May, Chinese President Xi Jinping stressed to ＂push forward the transformation from China Speed to China Quality, from Made in China to Created in China, and from Chinese Products to Chinese Brand＂. The ＂Three Transformations＂ are the specific requirements and goal of China＇s national development in the context that market should play a decisive role in the allocation of resources.     

重塑标准推行格局 推动LED照明的普及（英文）

正When you are enjoying the green,energy-saving and healthy lighting of IKEA LED luminaire,you may not realize that most of IKEA’s LED bulbs are produced by the LED luminaire smart manufacturing system of Hangzhou Zhongwei Photoelectricity CO.,LTD(ZVISION).No longer enclosed in the laboratory,the product standards are brought into the factory workshop and even to the entire production process.Thus,the standards are promoted and applied in a favorable way by enterprises,benefitting consumers with high quality products.     

Chinese Experts Contribute to ISO＇s New Toy Standards

正The international standard,ISO 8124-6,Safety of toys–Part 6:Certain phthalate esters in toys and children’s products,was officially issued by ISO worldwide on August 15.It was the first time for Chinese experts to lead the ISO standard development in toys industry.The standard was drafted by a group of Chinese experts from SAC/TC for toys and relevant Chinese departments and finally completed by a dedicated international group of experts.ISO 8124-6 makes a substantive breakthrough in the aspects of the scope of toys,limitation of plasticizer types,control of test cost,accuracy of test,operation convenience,etc.,offering the operational guidance for toy manufactures and testing laboratories.     

SAC Delegation Visits AENOR and Signs Cooperation Agreements

正SAC Administrator Tian Shihong led the Chinese delegation to visit the Spanish Association for Standardization and Certification(AENOR)on September 15,2014.Mrs.Begona Cristeto,the Vice-Minister of Industry,Energy and Tourism of Spain,and Mr.Avelino Brito,the President and CEO of AENOR greeted the delegation.The two sides had a deep and friendly discussion on strengthening the cooperation between China and Spain in the standardization field and promoting the standardization work to support the development of economy and trade in the two countries.