复合添加Ga,Al,Ag对Sn-9Zn钎料性能的影响

采用润湿平衡法研究了合金元素Ga,Al,Ag复合添加对Sn-9Zn钎料润湿性的影响.结果表明,Ga,Al,Ag的最佳添加量分别为0.2,0.002,0.25(质量分数,%);添加合金元素后钎料的高温抗氧化性能显著提高.俄歇电子能谱分析表明,Sn-9Zn-0.2Ga-0.002Al-0.25Ag钎料表面Al高度富集并形成一层致密的氧化膜,可阻挡氧向液态钎料内部扩散,减少钎料的氧化.Sn-9Zn-0.2Ga-0.002Al-0.25Ag钎料与Cu/Ni/Au基板之间的金属间化合物由一层平坦的AuZn3和颗粒状的AuAgZn2化合物组成.另外,微焊点力学试验表明,采用Sn-9Zn-0.2Ga-0.002Al-0.25Ag钎料时,电子元器件与基板间微焊点的力学性能比Sn-9Zn钎料略有提高.     

Ga、Al对Sn-Zn钎料耐蚀及高温抗氧化性能的影响

采用侵蚀失重法研究Ga、Al对Sn-9Zn钎料在3.5%NaCl水溶液中耐腐蚀性的影响.结果表明,添加Ga元素后,腐蚀产物的粘附性提高,均匀覆盖在钎料表面上,提高了钎料的耐蚀性能;添加Al以后,Zn和Al被选择性腐蚀,腐蚀随着Al含量的增加而加剧.采用热重分析(TGA)和俄歇电子能谱(AES)研究Ga、Al对Sn-9Zn钎料高温抗氧化性的影响.结果表明,Ga可在钎料表面形成一层集肤层;Al可在钎料表面形成一层致密的氧化膜,两者均可阻挡空气中的氧向钎料内部扩散,从而大大改善钎料的高温抗氧化性.     

稀土Ce元素对Sn-Zn-Bi-Ag-Al无铅钎料性能的影响

为了改善Sn-9Zn-4Bi-0.5Ag-0.05Al无铅钎料的综合性能,文中通过添加稀土元素Ce,研究了Ce元素对无铅钎料的润湿性能、抗剪强度以及熔点的影响.结果表明,稀土Ce元素的加入明显改善了钎料的润湿性能.当Ce的添加量为0.05wt%时,润湿性能最佳,钎焊接头的抗剪切强度也有明显提高,但随着稀土Ce元素的加入...     

Ag,Al,Ga对Sn-9Zn无铅钎料润湿性能的影响

采用润湿平衡法测试了Sn-9Zn-X(X为Ag,Al,Ga)无铅钎料分别配合ZnCl2-NH4Cl钎剂和免清洗助焊剂,在空气和氮气保护的两种条件下的润湿性能,分析研究了合金元素Ag,Al,Ga的添加量对Sn-9Zn-X无铅钎料润湿性的影响规律.结果表明,合金元素Ag,Al,Ga在Sn-9Zn中的最佳添加量(质量分数)分别为0.3%,0.005%～0.02%,0.5%.采用氮气保护可以显著改善Sn-9Zn-X无铅钎料的润湿性,而Sn-9Zn-X无铅钎料配合ZnCl2-NH4Cl钎剂时具有较好的润湿性,甚至优于Sn-3.5Ag-0.5Cu在相同条件下的润湿性.这一研究结果表明,通过研发适合于Sn-Zn系无铅钎料的高性能助焊剂,从而改善Sn-Zn系钎料的润湿性能是完全可行的.     

Sn-Zn-Bi-(P,Nd)无铅钎料的微观组织及性能

研究了复合加入P,Nd元素的Sn-8Zn-3Bi钎料的微观组织、力学性能、抗氧化性及润湿性.结果表明,单独加入元素P会导致Sn-8Zn-3Bi钎料组织中出现初生Zn相,而同时加入元素P和Nd不仅能够抑制初生Zn相的形成,钎料组织也能够得到细化,因此钎料的塑性提高,断后伸长率达到48%.P,Nd元素的复合添加能够在钎料表面形成稳定的扩散阻挡层,抑制P元素在长时间加热条件下的烧损,进一步降低表面的氧化速度.由于钎料的抗氧化性提高,Sn-8Zn-3Bi-0.1P-0.05Nd钎料呈现出更好的润湿性.     

氧含量对Sn-9Zn-2.5Bi-1.5In低温波峰焊焊接性能的影响

制备了一种新型Sn-9Zn-2.5Bi-1.5In钎料，开发了一套波峰焊氮气保护系统，考察了该钎料在不同氧含量的环境下的焊接质量. 结果表明，开发的氮气保护系统通过增加氮气流量可以将焊接区域内的动态氧含量降低到0.06%以下. 降低焊接区氧含量，可显著减少桥连、填充不良、气孔3类缺陷的数量，将不良率控制在0.20%以内. 在氧含量0.50%的临界值以下，该钎料可在锡炉设定温度为225 ℃的条件下进行低温焊接，焊接效果满足规模化生产需求. 通过能谱分析发现氧化物表面Zn元素含量比Sn-9Zn-2.5Bi-1.5In钎料升高84.9%，Zn元素的易氧化倾向是导致钎料形成大量氧化渣的主要原因. 降低焊接区域的氧含量可以有效抑制氧化渣的形成.采用氮气保护的方法可以解决Sn-Zn钎料在高氧环境下易出现的焊接缺陷问题，从而实现225 ℃低温波峰焊.     

铝/钢异种金属火焰钎焊接头组织和性能

通过扫描电镜、能谱分析和X射线衍射等方法研究了火焰钎焊时Zn-xAl钎料的润湿性能、铝/钢钎焊接头界面显微组织、金属间化合物层以及接头抗剪强度.结果表明,Zn-xAl钎料配合改性CsF-RbF-AlF₃钎剂,可以有效地去除母材表面氧化膜,从而提高钎焊接头力学性能.随着Al元素含量增加,钎料铺展性和填缝性随之提高,但是钎焊接头强度先升后降,Al元素含量为15%时,钎焊接头力学性能最佳.钎焊接头显微组织分析结果表明,金属间化合物主要为Fe₄Al₁₃相. Zn-xAl钎料中Al元素含量较低时,界面层由富锌相和Fe₄Al₁₃相组成.随着Al元素含量的增加,在Zn-25Al钎焊接头界面出现第二层金属间化合物Fe₂Al₅相.     

Ga和Ce复合添加对低银无镉钎料组织及性能的影响

通过向Ag17CuZnSn钎料中复合添加微量的Ga元素和稀土元素Ce,研究了Ga和Ce元素的复合添加对低银无镉钎料组织及焊接性能的影响。采用火焰钎焊方法得到黄铜与不锈钢异种金属钎焊接头。试验表明,随着Ga和Ce元素的添加低银钎料的固液相线温度不断下降。当Ga和Ce含量分别为2%和0.15%时,钎料在母材表面的铺展面达到最大值。Ga和Ce元素的复合添加对低银钎料中的CuZn化合物相有明显的细化作用,黄铜与不锈钢钎焊接头的抗剪强度最大值为378.6 MPa。在钎焊过程中,钎缝与不锈钢母材之间发生了明显的元素扩散,Ga元素的扩散率大于其他元素。同时当低银钎料中的Ce元素含量大于0.3%时,钎料组织中出现了新生成的块状的稀土相。     

ZL102合金用低温软钎料的研究

Sn-9Zn共晶钎料可以用于钎焊钎焊性极差的铸造铝合金ZL102，在Sn-9Zn钎料的基础上添加In元素，以提高钎料对ZL102合金的润湿。本文对Sn-9Zn和Sn-9Zn-5In两种软钎料对ZL102合金润型，界面结合等方面进行研究，分析实验结果可知，Sn-9Zn-5In钎料的性能优于Sn-9Zn共晶钎料。     

Ga和Ce复合添加对低银无镉钎料组织及性能的影响（英文）

通过向Ag17CuZnSn钎料中复合添加微量的Ga和稀土元素Ce,研究了Ga和Ce元素的复合添加对低银无镉钎料组织及焊接性能的影响。采用火焰钎焊方法得到黄铜与不锈钢异种金属钎焊接头。试验表明,随着Ga和Ce元素的添加低银钎料的固液相线温度不断下降。当Ga和Ce含量分别为2%和0.15%(质量分数)时,钎料在母材表面的铺展面达到最大值。Ga和Ce元素的复合添加对低银钎料中的CuZ n化合物相有明显的细化作用,黄铜与不锈钢钎焊接头的抗剪强度最大值为378.6 MPa。在钎焊过程中,钎缝与不锈钢母材之间发生了明显的元素扩散,Ga元素的扩散率大于其他元素。同时当低银钎料中的Ce元素含量大于0.3%时,钎料组织中出现了新生成的块状稀土相。     

Effects of Ga,Al, Ag,and Ce multi-additions on the wetting characteristics of Sn-9Zn lead-free solder

An orthogonal method was used to evaluate the effects of Ga, Al, Ag, and Ce multi-additions on the wetting characteristics of Sn-9Zn lead-free solders by wetting balance method. The results show that the optimal loading of Ga, Al, Ag, and Ce was 0.2 wt.%, 0.002 wt.%, 0.25 wt.%, and 0.15 wt.%, respectively. Intermetallic compounds (IMCs) formed at the interface between Sn-9Zn-0.2Ga-0.002Al-0.25Ag-0.15Ce solder and Cu substrate were investigated by scanning electron microscope (SEM) and energy dispersive spectroscopy (EDS) analysis. The SEM images illustrate that the IMCs can be divided into two portions from the substrate side to the solder side: a planar Cu₅Zn₈ layer and an additional continuous scallop-like AgZn₃ layer. The EDS analysis also shows that Ga segregates in the solder abutting upon the interface. X-ray photoelectron spectroscopy (XPS) and Auger electron spectroscopy (AES) of the surface components of Sn-9Zn-0.2Ga-0.002Al-0.25Ag-0.15Ce solder indicate that Al aggregates at the surface in the form of Al₂O₃ protective film, which prevents the further oxidation of the solder surface. On the other hand, Ce aggregates at the subsurface, which may reduce the surface tension of the solder and improve the wettability in consequence.     

The Inhibition of Tin Whiskers on the Surface of Sn-8Zn-3Bi-0.5Ce Solders

Through the refinement of the (Ce, Zn)Sn₃ intermetallic phase, the formation of tin whiskers, previously observed on the surface of a Sn-3Ag-0.5Cu-0.5Ce solder, was prevented in a Sn-9Zn-0.5Ce alloy. However, whisker growth can still occur on the surface of Sn-8Zn-3Bi-0.5Ce solder after air storage at room temperature and at 150 °C due to the formation of large (Ce, Zn)Sn₃ intermetallic clusters. Further experiments showed that decreasing the Bi-content in this Sn-8Zn-0.5Ce alloy to 1 and 2 wt.% can recover the beneficial effects of Zn additions on the refinement of the (Ce, Zn)Sn₃ phase and obviously reduce the appearance of tin whiskers. In addition, alloying the Sn-8Zn-3Bi-0.5Ce solder with 0.5 wt.% Ge, which increases the oxidation resistance of the (Ce, Zn)Sn₃ intermetallic clusters, can also effectively inhibit tin whisker growth.     

Electrochemical corrosion behaviour of Pb-free Sn-8.5Zn-0.05Al-XGa and Sn-3Ag-0.5Cu alloys in chloride containing aqueous solution

The electrochemical corrosion behaviour of Pb-free Sn-8.5Zn-0.05Al-XGa and Sn-3Ag-0.5Cu alloys was investigated in 3.5% NaCl solution by using potentiodynamic polarization techniques. The results obtained from polarization studies revealed that there was a negative shift in the corrosion potential with increase in Ga content from 0.02 to 0.2 wt% in the Sn-8.5Zn-0.05Al-XGa alloy. These changes were also reflected in the corrosion current density (I_corr) value, corrosion rate and linear polarization resistance (LPR) of the four element alloy. However, for Sn-3Ag-0.5Cu alloy a significant increase in the corrosion rate and corrosion current density was observed as compared to the four element alloys. SIMS depth profile results established that ZnO present on the outer surface of Sn-8.5Zn-0.05Al-0.05Ga alloy played a major role in the formation of the oxide film. Oxides of Sn, Al and Ga contributed a little towards the formation of film on the outer surface of the alloy. On the other hand, Ag₂O was primarily responsible for the formation of the oxide film on the outer surface of Sn-3Ag-0.5Cu alloy.     

Effect of cerium on microstructure and mechanical properties of Sn-Ag-Cu system lead-free solder alloys

The melting point, spreading property, mechanical properties and microstructures of Sn-3.0Ag-2.8Cu solder alloys added with micro-variable-Ce were studied by means of optical microscopy, scanning electron microscopy（SEM） and energy dispersive X-ray（EDX）. The results indicate that the melting point of Sn-3.0Ag-2.8Cu solder is enhanced by Ce addition; a small amount of Ce will remarkably prolong the creep-rupture life of Sn-3.0Ag-2.8Cu solder joint at room temperature, especially when the content of Ce is 0.1%, the creep-rupture life will be 9 times or more than that of the solder joint without Ce addition; the elongation of Sn-3.0Ag-2.SCu solder is also obviously improved even up to 15.7%. In sum, the optimum content of Ce is within 0.05%-0.1%.     

The effect of alloying element gallium on the polarization characteristics of Pb-free Sn-Zn-Ag-Al-XGa solders in NaCl solution

The polarization characteristics of Sn-8.5Zn-0.5Ag-0.1Al-XGa lead-free solders were investigated in 3.5% NaCl solution where X ranges from 0.05-1.5 wt%. The results show that Ga affects the anodic polarization behaviour of the solders. Passivation behaviour is observed for all the investigated Sn-8.5Zn-0.5Ag-0.1Al-XGa solders. Increase in the Ga content from 0.05 to 0.25 wt% increases the ability for passivation but the oxide film formed due to passivity is not so protective. However Ga content > 0.25 wt% enhances corrosion and decreases the protective power of the passive film. The magnitude of the passivation current densities depend on the composition of the solders and the potentials applied. Layers of oxides of tin and zinc are responsible for the passivation behaviour. XRD and SEM results revealed the formation of corrosion products like SnO, ZnO, SnO₂ at different potentials during the polarization study.     

High-Temperature Oxidation of a Sn-Zn-Al Solder

The oxidation of 91Sn-9(95Zn-5Al) solder in theliquid state, 250°C, was studied by thermalgravimetric analysis (TGA). The oxidation behavior of63Sn-37Pb, 91Sn-9Zn, 99.4Sn-0.6Al, and Sn was alsoinvestigated for comparison. The weight gains per unitsurface area descend in the order: 63Sn-37Pb > Sn> 91Sn-9Zn > 91Sn-9(95Zn-5Al) > 99.4Sn-0.6Al.The initial weight gains of the materials investigated increase linearly with reaction time, whileparabolic behavior exists after the linear stage. Therate constants of the oxidation reaction for the tworeaction stages were determined. Activation energies for oxidation of the five materials weredetermined in the range of 250 to 400°C. Theactivation energies, derived from the linear rateconstants for the early stages of oxidation, are 27.7kJ/mole for 99.4Sn-0.6Al, 23.3 kJ/mole for 91Sn-9Zn, 21.4kJ/mole for 91Sn-9(95Zn-5Al), 20.5 kJ/mole for63Sn-37Pb, and 19.8 kJ/mole for Sn. Thesurface-oxidation behavior was investigated further withelectron spectroscopy for chemical analysis (ESCA) and Auger electronspectroscopy (AES). AES profiles showed that oxides ofZn and Al formed on 91Sn-9Zn and 91Sn-9(95Zn-5Al)solders, while tin oxide is formed on 63Sn-37Pbsolder.     

稀土相表面特殊形态锡晶须生长现象

在Sn3.8Ag0.7Cu钎料中添加过量的稀土Ce和Er元素会在其内部形成尺寸较大的稀土相CeSn3和ErSn3.将钎料合金Sn3.8Ag0.7Cu1.0Ce/Er的铺展试样沿中心剖开,利用金相水砂纸及专用抛光液抛光后,将制备好的试样在空气中分别进行室温与150℃时效处理.分析了时效处理过程中稀土相CeSn3及ErSn3表面锡晶须的生长行为.结果表明,在稀土相的表面出现了大量规则的针状及线状锡晶须,它们在生长过程中始终保持了恒定的截面.试验中还发现了一些特殊形态的锡晶须,如锡晶须的分枝、合并以及锡晶须的搭接现象.