原位自生TiAl3增强Al基复合材料的组织结构及形成机理研究

采用冷喷涂技术沉积Ti-80Al（wt.%）复合涂层,通过热处理获得了原位自生TiAl3金属间化合物颗粒增强Al基复合材料涂层。采用SEM、EDS和XRD等分析了冷喷涂Ti/Al复合涂层在不同热处理温度下的组织结构演变规律及Ti、Al粒子间原位扩散反应过程,并对TiAl3金属间化合物的形成机理进行了探讨。结果表明,冷喷涂Ti/Al复合涂层组织致密,其相结构与喷涂粉末完全相同,450℃热处理后涂层局部区域发生Ti、Al间的固态扩散反应,并在Ti、Al粒子界面原位形成TiAl3金属间化合物,随着热处理温度升高,TiAl3金属间化合物的含量显著增加,600℃热处理后,Ti/Al复合涂层中的Ti粒子全部转变为TiAl3金属间化合物,获得原位自生TiAl3颗粒增强的Al基复合材料.     

反应合成Ti_3Al/TiC+Al_2O_3复合材料烧结过程热力学分析

将高能球磨后的Ti-Al粉末和TiC,Al2O3粉末混合进行热压烧结,在烧结的过程中反应生成金属间化合物为增强相的复合材料。通过对粉料的X射线衍射分析、热分析(DSC)和烧结体的成分分析表明,最终的金属间化合物只有Ti3Al而没有其它金属间化合物相。通过热力学计算,分析了反应烧结过程并发现在低温由固相间原子扩散控制生成TiAl3,TiAl,Ti3Al的渐进过程,和在高温下金属间化合物的合成机理,而且增强相和基体界面间处于稳定状态。     

反应合成Ti3Al/TiC＋Al2O3复合材料烧结过程热力学分析

将高能球磨后的Ti-Al粉末和TiC,Al2O3粉末混合进行热压烧结,在烧结的过程中反应生成金属间化合物为增强相的复合材料.通过对粉料的X射线衍射分析、热分析（DSC）和烧结体的成分分析表明,最终的金属间化合物只有Ti3Al而没有其它金属间化合物相.通过热力学计算,分析了反应烧结过程并发现在低温由固相间原子扩散控制生成TiAl3,TiAl,Ti3Al的渐进过程,和在高温下金属间化合物的合成机理,而且增强相和基体界面间处于稳定状态.     

不同工艺制备的TiAl金属间化合物微观组织特征

使用机械球磨制备细晶Ti/Al复合粉,采用不同的压制工艺,通过反应烧结和等温锻造方法获得不同晶粒尺寸的TiAl金属间化合物。对TiAl金属间化合物的微观组织特征进行了分析,研究了不同制备工艺对其微观组织的影响。结果表明:采用冷等静压630℃反应烧结及等温锻造工艺可以获得晶粒尺寸5～8μm的细晶TiAl金属间化合物;通过普通冷压、1250℃反应烧结与等温锻造后,也能获得近全致密的层片状TiAl金属间化合物,但晶粒尺寸为20～30μm。     

SiC／Ti基复合材料界面反应的热力学研究

通过建立热力学可能反应模型，分别计算了SCS－6 SiC长纤维增强Ti3Al和TiAl金属间化合物基复合材料界面反应的Gibbs函数变值△rG，并用△rG判据推测了界面反应产物并与透射电镜实验结果进行了对比分析。研究表明，由于TiAl中原子结合力较强，因而SCS－6 SiC/TiAl复合材料的界面反应较轻。所研究的2种复合材料界面反应的二元反应产物为TiC,Ti5Si3和Ti3Si,Ti-Si相图中的其它二元硅化物不可能形成。     

基于箔材反应退火合成的Ti Al基复合材料板材研究进展

本文综述了利用纯Ti箔和铝基复合材料(Al-MMC)箔反应退火合成Ti Al基复合材料板材的研究进展。该方法包括对多层Ti/Al-MMC复合板的变形和反应退火热处理,在避免对脆性TiAl金属间化合物直接变形的同时,制备出具有较高强度和延伸率的Ti Al基复合材料板材。对合成过程中Ti Al基复合材料板材的组织演化和形成机理进行了总结,重点阐明了铝基复合材料与Ti的两步热处理的反应机理,提出了消除Kirkendall孔洞的工艺方法,为大尺寸TiAl基复合材料板材的制备提供了可行的工艺方案。     

焊后热处理对钛/铝FSB接头组织及性能的影响

研究了6082铝合金和TC4钛合金分别添加钎料锌和镍下的搅拌摩擦钎焊(FSB)搭接接头微观组织及焊后热处理后接头界面金属间化合物(IMC)的生成种类和先后顺序以及生长动力学模型。研究表明:添加钎料锌时,界面金属间化合物主要由AlZn、TiAl、TiAl2、TiAl3组成,先后顺序为TiAl2→TiAl3→TiAl→AlZn,并获得了界面IMC层的生长动力学模型为;添加钎料镍时,界面金属间化合物层主要由TiNi、Al3Ni2、Ti3Al和TiAl组成,先后顺序为776 K以下,Ti-Ni-Al焊接界面金属间化合物形成的顺序是Al3Ni2→TiNi→TiAl→Ti3Al,776 K以上时生成顺序为Al3Ni2→TiNi→Ti3Al→TiAl,并获得了界面IMC层的生长动力学模型。界面IMC层的厚度均随着温度的提高或保温时间的延长而增加。添加锌的接头的剪切强度由未热处理时的154 MPa提高到194 MPa,而添加钎料镍的接头由142 MPa提高至166 MPa。     

SiC／TiAl界面固相反应研究

使用扫描电子显微镜、电子能谱仪、X射线衍射仪对经950～1100℃热处理的SiC/TiAl平面界面偶界面固相反应层的成分分布、微结构及相组成等进行了分析研究,讨论了SiC/TiAl界面固相反应机制,并对热处理过程中反应层成长的动力学过程进行了探讨,获得相应的动力学方程.结果表明,SiC/TiAl界面固相反应层主要由TiC、Ti5Si3Cx及Ti(Al,Si)2构成.其中,TiC和Ti5Si3Cx主要富集于邻近SiC的反应区,而Ti(Al,Si)2富集于邻近TiAl侧的反应区.SiC/TiAl界面固相反应的发生归因于TiC和Ti5Si3Cx数值大的负吉布斯自由能变化.SiC/TiAl界面固相反应层遵循抛物线生长规律,为扩散控制的反应过程,反应速率常数为:K=8.47×10-3exp(-322×103/RT)(m2/s).     

Al2O3/TiAl复合材料的原位合成及反应机制的研究

利用Al-Ti-TiO2体系的放热反应,原位合成了Al2O3/TiAl复合材料.借助示差热分析法探讨了体系的反应机制,采用XRD、SEM和OM分析了复合材料的相组成及显微组织.结果表明,原位合成Al2O3/TiAl复合材料由TiAl、Ti3Al和Al2O3相组成,Al2O3颗粒分布于TiAl和Ti3Al双相交界处,并存在一定团聚.随其含量增加,团聚程度加剧,晶粒尺寸减小.Ti和Al反应生成TiAl3放出的热量使部分TiAl3相处于液相状态,熔融的体积分数约为87.87%,液相的存在提高了颗粒间的润湿性,同时放出的热量是引发后续反应的原因之一.TiAl3与Al-TiO2的还原反应生成的活性Ti原子结合最终生成了TiAl和Ti3Al相.     

热压烧结制备钛基合金TiAl+Ti及其显微结构

在1473 K,30 MPa,1.5 h的热压条件下直接烧结TiAl金属间化合物和Ti混合粉末,制备了钛基合金(TiAl+Ti)样品,采用XRD、SEM研究了2种不同成分配比对烧结产物相组成及显微结构的影响。结果表明,不同成分配比热压烧结体的显微组织分布相差较大,但相组成基本相同;对于TiAl和Ti体积比7:3的钛基合金样品,Ti粉末中Fe元素易于固溶到Ti_2Al和Ti_3Al中,析出相主要由TiAl、Ti_2Al(Fe)、Ti_3Al(Fe)和富Ti相组成;该比例的混合粉末在热压烧结过程中发生了不同程度的扩散反应,最终形成了组织渐变的Ti/Ti_3Al(Fe)//Ti_2Al(Fe)/TiAl显微结构。     

新型的治疗阿尔茨海默氏症药物(1-二甲基磷酰基-2,2,2-三氯)-乙基-1-醇烟酸醋对体外神经细胞的作用

目的: 观察本实验室合成的一种治疗阿尔茨海默氏症(AD)的药物(1-二甲基磷酰基-2, 2, 2 -三氯)-乙基^-1-醇烟酸醋(NMF),对体外培养的皮层神经细胞活性的影响以及对海人藻酸(KA)所致的神经损伤的保护作用。方法: 采用体外培养皮层神经元的方法,解剖分离 15 d胚胎小鼠皮层神经细胞, 接种于 96孔板,48 h 后加药并培养 72 h,以 MIT 法 观察 NMF 对小鼠皮层神经细胞活性的影响;同时将接种于 24 孔板的细胞预先给予 NMF,d 3 时加或不加KA处理后,以台盼蓝染色鉴别并计数死、活细胞,可得出细胞的存活率。结果: NMF 明显促进胎鼠皮层神经元活性,其中 NMF1、0. 1、10nmol·L^-1促进神经元活性增殖率分别高达 34.7%、37.4%、36. 7%, NMF 明显促进正常胎鼠皮层神经元存活卒,与对照组比较,10nmol·L^-1 NMF 对皮层神经元的存活率分别提高 39.3%、73.5%。 NMF能显著 对抗 KA 所致的神经元损伤,与 KA 损伤组相比, NMF0.1、10、10nmol·L^-1对损伤皮层神经元的保护率分别为 77.30%、80.10%、84.15%。结论: NMF 明 显促进胎鼠皮层神经元的洁性、提高正常皮层神经元,的存活卒,并能有效地保护KA所致的神经元损伤,提示 NMF 是一种很有潜力的治疗 AD 的药物。     

Three-Dimensional Growth of Coherent Ferrite in Austenite: A Molecular Dynamics Study

Coherent second phase often exhibits anisotropic morphology with specifi c orientations with respect to both the second and the matrix phases. As a key feature of microstructure, the morphology of the coherent particles is essential for understanding the second-phase strengthening eff ect in various industrial alloys. This letter reports anisotropic growth of coherent ferrite from austenite matrix in pure iron based on molecular dynamics simulation. We found that the ferrite grain tends to grow into an elongated plate-like shape, independent of its initial confi guration. The fi nal shape of the ferrite is closely related to the misfi t between the two phases, with the longest direction and the broad facet of the plate being, respectively, consistent with the best matching direction and the best matching plane calculated via the Burgers vector content(BVC) method. The strain energy calculation in the framework of Eshelby's inclusion theory verifi es that the simulated orientation of the coherent ferrite is energetically favorable. It is anticipated that the BVC method will be applicable in analysis of anisotropic growth and morphology of coherent second phase in other phase transformation systems.     

Effect of Short-Time Aging on the Pitting Corrosion Behavior of a Novel Lean Duplex Stainless Steel 2002

The effect of short-time aging in the temperature range between 400 and 1000 °C on the pitting corrosion behavior and mechanical property of a novel lean duplex stainless steel(LDSS) 2002 was investigated through the potentiostatic critical pitting temperature(CPT) tests and the Charpy impact tests. Both the pitting corrosion resistance and the toughness of aged specimens degraded due to the precipitation of detrimental secondary phases and the most significant reduction of CPT and impact energy emerged at 650 °C concurrently. The CPT of LDSS 2002 specimen aged at 650 °C decreased by 28 °C, and the impact energy dropped from 69 to 29 J/cm~2 compared with the solution-annealed sample. Transmission electron microscopy characterization showed that the main precipitates in LDSS 2002 were Cr_2N and M_(23)C_6 along the ferrite–austenite grain boundaries.     

INTRODUCTION TO PATENTS

The invention provides a method of making a mold which can reduce SOx generation rate while preventing decrease in hardening rate in the case of using sulfuric acid for a hardener composition. The method has a mixture step in which fire-resistant particles, a hardener composition and a binder composition are mixed to obtain a composition for a mold. The hardener composition contains sulfuric acid. In the mixture step, sodium carbonate is added. A molar ratio of the sulfuric acid to the sodium carbonate is 0.5 or more and 4.0 or less.     

China Foundry Week 2014

China Foundry Week, hosted by the Foundry Institution of Chinese Mechanical Engineering Society （FICMES） each year, is a large academic event in China. It is one of the ten high-impact activities sponsored by the Chinese Mechanical Engineering Society.     

17th Conference of Hydrodynamic and Electromechanical Control Engineering Call for papers

正1.Contents In order to promote the academic exchanges and technical communication of the research in the field of fluid power transmission and control,fluid control engineering specialized committee of the Chinese Society of Theoretical and Applied Mechanics will hold the 17th Conference of Hydrodynamic and Electromechanical Control Engineering on July 27-29,2014 in Tibet,Lhasa city.     

Information for Contributors

正The Transactions of Nonferrous Metals Society of China,founded in 1991 and sponsored by The Nonferrous Metals Society of China,is published monthly now and mainly contains reports of original research which reflect the new progresses in the field of nonferrous metals science and technology,including mineral processing,extraction metallurgy,metallic materials and heat treatments,metal working,physical metallurgy,powder metallurgy,with the emphasis     

Preface

<正>We are pleased to present this Special Issue of Transactions of Nonferrous Metals Society of China containing selected papers from the First Asian Conference on Aluminum Alloys(ACAA-2013),held in Beijing,China,13–17 October 2013.This conference has been initiated,with approval of     

Information for Contributors

The Transactions of Nonferrous Metals Society of China, founded in 1991 and sponsored by The Nonferrous Metals Society of China, is published monthly now and mainly contains reports of original research which reflect the new progresses in the field of nonferrous metals science and technology, including mineral processing, extraction metallurgy, metallic materials and heat treatments, metal working, physical metallurgy, powder metallurgy, with the emphasis on fundamental science. It is the unique preeminent publication in English for scientists, engineers, under/post-graduates on the field of nonferrous metals industry. This journal is covered by many famous abstract/index systems and databases such as SCI Expanded, Ei Compendex Plus, 1NSPEC, CA, METADEX, AJ and JICST.     

Rheology Feature of Simple Metal Melt

The rheology feature of Sb, Bi melt and alloys was studied using coaxial cylinder high-temperature viscometer. The results showed that the curve of torsion-rotational speed for Sb melt presents a linear relation in all measured temperature ranges, whereas for the Bi melt, the curve presents obvious non-Newtonian feature within the low temperature range and at relative high shear stress. The rheology feature of Sb80Bi20 and Sb20Bi80 alloy melts was well correlated with that of Sb and Bi, respectively. It is considered that the rheology behavior of Sb melt plays a crucial role in Sb80Bi20 alloy and that of Bi melt plays a crucial role in Sb20Bi80 alloy.