常温挤出糖霜3D打印机设计

目的:设计一款满足安全、卫生、操作便捷、结构性能稳定等要求的糖霜制品3D打印机.方法:打印机主要包括机械结构和控制系统,机械结构方面采用龙门架结构,并对传统的打印料罐进行改良.控制系统采用“工控机+运动控制卡”的模式.结果:该打印机可快速更换料罐(30s内),打印机成型速度快(≥5000mm/min),速度可调;成型精度控制在1mm 以内;成型件的强度、膨胀率和表面粗糙度指标均较好.自带光源的图像识别及处理系统能够识别产品形状、个数及完整性等.结论:改良后的料罐提高了半流体食品打印的卫生性、生产效率,且便于耗材的更换,能加工出复杂糖画模型以满足造型独特的个性化糖艺制品的需求.     

掺钪AlN材料特性及HBAR器件性能研究

该文基于掺钪AlN薄膜制备了高次谐波体声波谐振器(HBAR),研究了钪(Sc)掺杂浓度对AlN压电薄膜材料特性及器件性能的影响。研究表明,当掺入Sc的摩尔分数从0增加到25%时,压电应力系数e₃₃增加、刚度 下降,导致Al₁-_xSc_xN压电薄膜的机电耦合系数 从5.6%提升至15.8%,从而使HBAR器件的有效机电耦合系数 提升了3倍。同时,当Sc掺杂摩尔分数达25%时,Al₁-_xSc_xN(x为Sc掺杂摩尔分数)压电薄膜的声速下降13%,声学损耗提高,导致HBAR器件的谐振频率和品质因数降低。     

Estimating long-term time-resolved indoor PM2.5 of outdoor and indoor origin using easily obtainable inputs

To evaluate the separate impacts on human health and establish effective control strategies, it is crucial to estimate the contribution of outdoor infiltration and indoor emission to indoor PM_2.5 in buildings. This study used an algorithm to automatically estimate the long-term time-resolved indoor PM_2.5 of outdoor and indoor origin in real apartments with natural ventilation. The inputs for the algorithm were only the time-resolved indoor/outdoor PM_2.5 concentrations and occupants’ window actions, which were easily obtained from the low-cost sensors. This study first applied the algorithm in an apartment in Tianjin, China. The indoor/outdoor contribution to the gross indoor exposure and time-resolved infiltration factor were automatically estimated using the algorithm. The influence of outdoor PM_2.5 data source and algorithm parameters on the estimated results was analyzed. The algorithm was then applied in four other apartments located in Chongqing, Shenyang, Xi'an, and Urumqi to further demonstrate its feasibility. The results provided indirect evidence, such as the plausible explanations for seasonal and spatial variation, to partially support the success of the algorithm used in real apartments. Through the analysis, this study also identified several further development directions to facilitate the practical applications of the algorithm, such as robust long-term outdoor PM_2.5 monitoring using low-cost light-scattering sensors.     

Enhanced electrochemical performance of LiNi0.8Co0.1Mn0.1O2 via titanium and boron co-doping

Titanium and boron are simultaneously introduced into LiNi_0.8Co_0.1Mn_0.1O₂ to improve the structural stability and electrochemical performance of the material. X-ray diffraction studies reveal that Ti⁴⁺ ion replaces Li⁺ ion and reduces the cation mixing; B³⁺ ion enters the tetrahedron of the transition metal layers and enlarges the distance of the [LiO₆] layers. The co-doped sample has spherical secondary particles with elongated and enlarged primary particles, in which Ti and B elements distribute uniformly. Electrochemical studies reveal the co-doped sample has improved rate performance (183.1 mAh·g^-1 at 1 C and 155.5 mAh·g^-1 at 10 C) and cycle stability (capacity retention of 94.7% after 100 cycles at 1 C). EIS and CV disclose that Ti and B co-doping reduces charge transfer impedance and suppresses phase change of LiNi_0.8Co_0.1Mn_0.1O_2.     

ZY6400/23/47型掩护式液压支架偏置改造

铁煤集团大兴矿(以下简称"大兴矿")2019年产240万t,井田位于铁法煤田的西南角,火成岩侵入及地质构造复杂,煤层破坏程度严重[1-2]。受火成岩影响,煤层瓦斯含量大幅增加[3-4],渗透性能差,力学强度低,煤的含水率低,自然发火期较短,是煤与瓦斯突出矿井。在采煤过程中,防治自然发火是重中之重,综采设备在设计初期未考虑实施灭火的操作空间,为此,笔者提出通过改造综采设备增加实施灭火的操作空间,降低出现自然发火灾害时防治的难度,保证采煤安全。     

超低排放改造后烟气余热利用设备存在问题及防治措施

随着火电厂超低排放改造的普遍应用，低温省煤器等烟气余热利用设备获得了广泛应用。本文针对烟气余热利用设备在实际工程应用中所存在的低温腐蚀、磨损、积灰堵塞以及振动等问题，分析了形成原因及主要影响因素，提出了选用耐低温腐蚀性能优异的材料制造换热器，合理设计受热面结构型式，控制烟气流速和受热面金属壁温，加装吹灰设备以及导流板和防振隔板等防治对策，有效地解决了烟气余热利用设备所存在的低温腐蚀、磨损、积灰堵塞以及振动等问题。     

倾斜摄影测量技术在古建筑测绘中的运用研究——以郴州市汝城县朱氏宗祠建筑测绘为例

为测试倾斜摄影测量技术路线,并通过实际项目的应用,解决传统古建筑建模过程中存在的时间成本高、难以还原复杂场景等问题。按照倾斜摄影技术的技术路线,进行朱氏宗祠建筑测绘试验,并通过基于altizure软件建立三维模型来展现倾斜摄影测量技术流程。验证无人机倾斜摄影应用于古建筑三维建模的可行性和可操作性。     

A Reduced Reachability Tree for a Class of Unbounded Petri Nets

As a powerful analysis tool of Petri nets, reachability trees are fundamental for systematically investigating many characteristics such as boundedness, liveness and reversibility. This work proposes a method to generate a reachability tree, called ωRT for short, for a class of unbounded generalized nets called ω-independent nets based on new modified reachability trees (NMRTs). ωRT can effectively decrease the number of nodes by removing duplicate and ω-duplicate nodes in the tree, and verify properties such as reachability, liveness and deadlocks. Two examples are provided to show its superiority over NMRTs in terms of tree size.