超高效液相色谱串联质谱法测定烟草中的噁霉灵残留

为降低烟草中噁霉灵检测中的基质干扰，提高检测灵敏度和和稳定性，通过试验建立了以QuEChERS为样品前处理方法、液相色谱串联质谱仪为检测仪器的烟草中噁霉灵残留检测方法。样品加水浸润后，经丙酮提取、盐析试剂包除水、石墨化炭黑除杂后，采用Agilent ZORBAX 300SB-C8液相色谱柱（2.1 mm×100 mm，1.8 μm）分离，甲醇-水程序洗脱，ESI雾化，串联质谱MRM检测。结果发现，该方法在0.0025~0.0500 mg/L范围内线性良好，决定系数r²=0.9996，定量检测限1.06 μg/L，回收率在90.8%~92.0%之间，相对标准偏差为5.1%。运用该方法测定烟草中的噁霉灵，操作简单，检测精度高，满足CORESTA对烟草农残检测的要求。     

高密度聚乙烯/铅硼复合材料屏蔽性能和力学性能研究

研究了高密度聚乙烯/铅硼复合材料的屏蔽性能和力学性能，通过屏蔽仿真比较了密度及碳化硼（B4C）含量对屏蔽性能的影响，通过试验比较了B4C含量对屏蔽性能、弯曲强度及冲击强度的影响。仿真结果表明,随聚乙烯/铅硼复合材料密度升高，快中子屏蔽性能下降，热中子屏蔽性能和γ屏蔽性能提高；保持聚乙烯/铅硼复合材料密度不变，随B4C含量的提高，中子屏蔽性能提高而γ屏蔽性能下降;实验数据表明,随B4C含量的升高，高密度聚乙烯/铅硼材料的快中子屏蔽性能、热中子屏蔽性能升高，γ屏蔽系数下降，冲击强度和弯曲强度下降明显，屏蔽性能测试结果和仿真结果规律性相符；综合仿真结果和实验数据表明，含B4C 2 %左右的高密度聚乙烯/铅硼复合材料同时具有较好的屏蔽性能和力学性能。     

Systematic convergence of nonlinear stochastic estimators on the Special Orthogonal Group SO(3)

This paper introduces two novel nonlinear stochastic attitude estimators developed on the Special Orthogonal Group with the tracking error of the normalized Euclidean distance meeting predefined transient and steady‐state characteristics. The tracking error is confined to initially start within a predetermined large set such that the transient performance is guaranteed to obey dynamically reducing boundaries and decrease smoothly and asymptotically to the origin in probability from almost any initial condition. The proposed estimators produce accurate attitude estimates with remarkable convergence properties using measurements obtained from low‐cost inertial measurement units. The estimators proposed in continuous form are complemented by their discrete versions for the implementation purposes. The simulation results illustrate the effectiveness and robustness of the proposed estimators against uncertain measurements and large initialization error, whether in continuous or discrete form.     

机加工孔套管抗挤压强度有限元分析

套管屈服强度直接影响套管抗挤压性能，套管在加工孔过程中可能诱发孔眼附近材料发生金属相变，导致套管屈服强度不再均匀分布，进而影响套管抗挤压强度。在相同工况下，对比了P110完整套管和机加工孔套管的抗挤压强度，以此为参照组分析了相变区域面积和相变区域屈服强度对机加工孔套管抗挤压强度的影响。结果表明，机加工孔会改变材料屈服强度，进而影响套管抗挤压性能。随金属相变区域屈服强度减小，机加工孔套管抗挤压强度减弱；当金属相变区域屈服强度增大时，机加工孔套管抗挤压强度增强。且机加工孔套管相变区域面积对机加工孔套管抗挤压强度的影响随相变区域屈服强度增加而逐渐削弱。     

基于旋翼负压混合吸附的爬壁清洗机器人系统动力学性能研究

针对爬壁清洗机器人越障时,负压装置的吸附力下降导致吸附不稳定的问题,设计了一种旋翼负压混合吸附工作的多边形履带清洗机器人,并对爬行稳定性及越障性能进行了动力学分析。首先根据机器人爬壁的运动原理,建立机器人沿玻璃幕墙上的动力学模型,计算出电机理论驱动力矩;其次分析机器人在跨越障碍过程中的运动模型,结合与壁面接触的实际受力状态,对越障过程中关键阶段的本体倾翻、滑移两种失效形式进行运动学和动力学分析;然后根据玻璃幕墙实际的障碍高度,确定多边形履带的参数和理论驱动力矩的大小,并研制了实验样机进行爬行和越障试验,结果表明所设计的机器人具有良好的越障性能。     

煤矿工业场地道路照明接地系统问题探讨

文章简要介绍了煤矿工业场地的特点和低压配电系统接地方式分类,从安全性、经济性的角度分析了TN接地系统和TT接地系统在道路照明回路中的优缺点。通过对比TN-S系统与TT系统的接地故障电流差异、TN-S接地系统用于道路照明的等电位联结困难程度,总结出煤矿工业场地的道路照明配电系统适宜采用TT接地方式。并且详细阐述了TT接地系统剩余电流动作保护器保护整定方法和灵敏度校验方法,列举了煤矿工业场地道路照明选用TT系统时需要注意的中性线不可重复接地的问题。     

采油树平板闸阀柔性密封圈结构优化设计

为了提高采油树平板闸阀密封圈的密封性能,在泛塞封的基础上,设计一种密封圈本体唇边开有锯齿状凸起的新型柔性密封结构;运用有限元分析方法模拟密封圈的工作状况,分析柔性密封结构特性参数对密封圈密封性能的影响,获得不同柔性密封圈结构参数下密封面间接触应力分布规律,并对新型密封结构进行优化。结果表明:密封面间最大接触应力随唇边锯齿数量、唇边夹角度数的增大而增大,随唇谷夹角度数的增大而减小;新型密封结构选择锯齿数量为3、唇边夹角为20°、唇谷夹角为30°的特性参数时,其最大接触应力比常规Y形密封圈提高了15倍;新型柔性密封结构的密封圈与阀杆、阀盖壁面间接触应力比常规Y形密封圈有显著提高,提高了密封圈的密封性能。     

Sustainable supply chain management in Indian organisations: an empirical investigation

The present work is an attempt to investigate the adoption of sustainable supply chain management (SSCM) practices amongst manufacturing and process based organisations in India and its impact on organisational performance encompassing all three dimensions of sustainability. SSCM practices conceived in the present study include environmental management practices (EMP), socially inclusive practices for employees (SPE), socially inclusive practices for community (SPC), operations practices (OP) and supply chain integration (SCI) which were treated as exogenous variables. Organisational performance considered in this study includes five dimensions, namely environmental performance (EPR), employee-centred social performance (ESP), community-centred social performance (CSP), operations performance (OPR) and competitiveness, which were regarded as endogenous variables. The analysis was carried out with the help of structural equation modelling considering natural logarithm of manpower as a control variable. Few major findings are mentioned. EMP does not have any significant association with OPR, nor does it result in competitiveness. However, when jointly mediated through both EPR and OPR, EMP leads to competitiveness. SPC has significant negative association with competitiveness, when only direct relationship is considered. However, indirect relationship between SPC and competitiveness shows significant positive association when mediated through CSP. The resultant total effect between SPC and competitiveness turns out to be insignificant. Further, OPR fully mediates the relationship between OP and competitiveness. Managerial implications of the findings are discussed.     

Performance of LiNi1/3Co1/3Mn1/3O2 prepared from spent lithium-ion batteries by a carbonate co-precipitation method

Spherical LiNi_1/3Co_1/3Mn_1/3O₂ cathode particles were resynthesized by a carbonate co-precipitation method using spent lithium-ion batteries (LIBs) as a raw material. The physical characteristics of the Ni_1/3Co_1/3Mn_1/3CO₃ precursor, the (Ni_1/3Co_1/3Mn_1/3)₃O₄ intermediate, and the regenerated LiNi_1/3Co_1/3Mn_1/3O₂ cathode material were investigated by laser particle-size analysis, scanning electron microscopy–energy-dispersive spectroscopy (SEM-EDS), thermogravimetry–differential scanning calorimetry (TG-DSC), X-ray diffraction (XRD), inductively coupled plasma–atomic emission spectroscopy (ICP-AES), and X-ray photoelectron spectroscopy (XPS). The electrochemical performance of the regenerated LiNi_1/3Co_1/3Mn_1/3O₂ was studied by continuous charge–discharge cycling and cyclic voltammetry. The results indicate that the regenerated Ni_1/3Co_1/3Mn_1/3CO₃ precursor comprises uniform spherical particles with a narrow particle-size distribution. The regenerated LiNi_1/3Co_1/3Mn_1/3O₂ comprises spherical particles similar to those of the Ni_1/3Co_1/3Mn_1/3CO₃ precursor, but with a narrower particle-size distribution. Moreover, it has a well-ordered layered structure and a low degree of cation mixing. The regenerated LiNi_1/3Co_1/3Mn_1/3O₂ shows an initial discharge capacity of 163.5 mA h g^?1 at 0.1 C, between 2.7 and 4.3 V; the discharge capacity at 1 C is 135.1 mA h g^?1, and the capacity retention ratio is 94.1% after 50 cycles. Even at the high rate of 5 C, LiNi_1/3Co_1/3Mn_1/3O₂ delivers the high capacity of 112.6 mA h g^?1. These results demonstrate that the electrochemical performance of the regenerated LiNi_1/3Co_1/3Mn_1/3O₂ is comparable to that of a cathode synthesized from fresh materials by carbonate co-precipitation.     

旱地西红柿种植技术

随着人民生活水平的提高,旱地西红柿种植面积逐年增大,但由于种植技术的缺乏,产量和质量均得不到提高。文章通过多年的研究,对西红柿从育苗、施肥、覆膜种植到管理进行了系统的阐述,有效提高山区人民旱地西红柿的种植水平,增加农民收入。