对苯二酚-甲醛有机气凝胶的结构测试及性能研究

首次用溶胶-凝胶法和CO2超临界干燥技术制备了对苯二酚-甲醛有机气凝胶,并经高温碳化处理得到其碳气凝胶,测得气凝胶的比表面积由碳化前的375.28 M2/G增大到碳化后的468.66 M2/G,碳气凝胶的孔径集中分布在15NM以内。观察到其表观形貌,以及碳气凝胶中存在微晶结构。研究了不同反应物配比对凝胶性能的影响,并发现碳气凝胶具有良好导电性。     

Synthesis of Ba(Mg1/3Ta2/3)O3 Microwave Ceramics through a Sol–Gel Route Using Acetate Salts

A sol–gel process to unsophisticatedly synthesize Ba(Mg_1/3Ta_2/3)O₃ (BMT) ceramics at low cost has been developed in the present work. This process involves the reaction of TaCl₅ with acetates of Ba and Mg in the presence of citric acid. Pure BMT polycrystalline powders can be obtained by calcining the synthesized products at 1000°C. The BMT powders were found to have a primary particle size as small as 100 nm. BMT ceramics with favorable structural characteristics can be obtained from sintering of the sol–gel BMT at temperatures much lower than that for the conventional solid-state BMT. Sintering the sol–gel BMT in pellet form at 1300°C resulted in an ordering parameter of 0.72 for the pellet, and a relative density of >95% was achieved with sintering at 1500°C. The grain size of the sintered sol–gel BMT was large and uniform in comparison with the products from the solid-state method. Using the sol–gel route, sintering at temperatures as low as 1400°C gave ceramics with acceptable microwave dielectric properties (a dielectric constant of 16 and Qf factor of 14 400 GHz), while higher temperatures (>1600°C) are needed for the solid-state route to give similar properties.     

TiO2/NiO复合纳米纤维制备及光催化性能研究

通过溶胶一凝胶过程,采用静电纺丝技术,以聚乙烯吡略烷酮(PVP,Mn=900 000)和钛酸正丁酯为前驱物,制备了PVP/Ti(OPr)./Ni(CH3COO)2复合一维纳米纤维材料.经控温缓慢氧化分解,在600℃的条件下成功制备了直径50～100 nmTiO2/NiO纳米纤维.采用扫描电镜、红外光谱、X射线粉末衍射、拉曼等分析手段对样品进行了表征,系统地介绍了TiO2光催化作用机理并在紫外灯下使用样品对罗丹明B溶液进行降解实验.结果显示,0.5%TiO2/NiO复合纳米纤维具有良好的光催化活性.     

聚酰亚胺复合杂化环氧树脂基增强浆料的制备与性能研究

采用溶胶-凝胶技术,在合成的聚酰胺酸(PAA)中对纳米SiO2/TiO2前驱体进行原位改性,添加硅烷偶联剂(WD-50),利用超声空化及复配技术制备了环氧树脂基-SiO2.TiO2复合杂化聚酰亚胺增强浆料,并采用FTIR、DSC、粒径分析仪、力学测试、STM等手段对所制备增强浆料的性能及其在碳纤维上浆膜铺展的显微形貌进行了分析.结果表明:SiO2.TiO2以纳米粒度分布于浆膜中;上浆后碳纤维轴向界面有一层纳米级粒状突起,表面较为粗糙,改善了碳纤维的界面性能,杂化浆料处理后碳纤维的抗拉强度及层间剪切强度显著提高.     

溶胶-凝胶法制备掺镧钛酸钡薄膜及其光学性质研究

以硝酸镧、醋酸钡、钛酸四丁酯为原料,采用溶胶一凝胶旋涂法制备掺La的钛酸钡薄膜,研究薄膜的晶体结构、表面形貌、紫外-可见光吸收性能及光学带隙。研究结果表明,纯钛酸钡和掺La钛酸钡薄膜均为单一四方钙钛矿结构,La3＋的引入可以使钛酸钡薄膜在可见光区的透过率和光学带隙有一定程度下降,而退火温度对掺镧钛酸钡薄膜光学带隙基本无...     

基于溶胶凝胶法的TiO2溶胶的制备

用N-N二甲基乙酰胺(DMAC)作溶剂,钛酸丁酯作前驱物,冰乙酸为稳定剂,通过溶胶凝胶法制得了二氧化钛(TiO2)溶胶,并且对加水方式、加水量、溶剂量、pH值、温度等影响因素进行了考察.结果表明,当采用分散加水方式,温度在25℃～35℃以下,DMAC与钛酸丁酯的体积比为3.5:1,V(H2O)/V(Ti(OC4H9)4...     

Thermoelectric Properties of Ca_3Co_4O_9 Ceramics

Ca3Co4O9 ceramics were prepared using the sol-gel process with ordinary pressing sintering and their thermoelectric properties were measured from room temperature to 673 K. The experimental results show that single phase Ca3Co4O9 can be fabricated at 750-900 ℃ in different citrate acid molar proportions for 0.2-1.0. For all the oxides, both the Seebeck coefficients S and the electrical conductivitiesκincrease with the increasing temperature. The Seebeck coefficients S are all positive. The thermal conductivities κ increase with the increasing temperature also and the lattice thermal conductivityκl plays an important role to the thermal conductivity κ. The citrate acid molar proportions have a large influence on the particle sizes, which influences the thermoelectric properties of the ceramics. The figure of merit increases with the increasing temperature and reaches 4.5×10-5 K-1 at 573 K for the sample in the citrate acid molar proportion of 0.46.     

外界条件对纳米TiO2光催化性能的影响

为找到纳米TiO2的最佳催化条件,以钛酸丁酯为原料,采用溶胶-凝胶法制备纳米级的掺杂Fe3+的TiO2粉末.通过XRD确定其相组成,利用紫外可见分光光度计测定光催化活性,研究外界条件包括光强度、溶液的pH值及环境温度对光催化反应的影响.结果表明:光强度在一定范围内越大光催化活性越高;pH值在4时光催化活性最大;环境温度对光催化反应无太大影响.在较高的光强度、pH=4的条件下光催化活性最好.     

Hybrids perfluorosulfonic acid ionomer and silicon oxide membrane for application in ion-exchange polymer-metal composite actuators

This paper reports a new technique to fabricate an ion-exchange polymer-metal composite (IPMC) actuator. This technique is based on a hybrid organic-inorganic composite membrane. In the fabrication course, silica oxide particles, prepared from hydrolysis of tetraethyl orthosilicate in situ with sol-gel reaction, co-crystallize with perfluorosulfonate acid (PFSA) ionomer. Attenuated total reflectance fourier transform infrared spectroscopy (ATR-FTIR) analyses demonstrate that a highly water-saving hybrid mem...     

Thin-Layer Dielectrics in the Pb[(Mg1/3Nb2/3)1-xTix]O3 System

Thin layers of Pb[(Mg_1/3Nb_2/3)_{1– x} Ti _x ]O₃ (PMNT) were prepared by spin casting alkoxide-based solutions on platinized Si. The effects of additives, heat treatment, and composition ( x = 0 to 0.9) on perovskite phase development, ceramic microstructure, and dielectric properties are reported. Depending upon the processing conditions, ceramic thin layers could be formed in a nonferroelectric pyrochlore phase (A₂B₂O₆) or in a ferroelectric perovskite phase (ABO₃). The dimensions of the pyrochlore and perovskite units cells were related and increased with Mg and Nb contents. To minmize pyrochlore formation, the most effective processing method involved rapid heat treatment between successive solution depositions. Phase development and microstructure were also affected by solution additives. Additions of benzoic acid were found to affect the structure in solution and the later organic pyrolysis behavior from thin layers. The effect of composition on the dielectric and ferroelectric properties is also reported.