聚乙烯催化剂表面分形和多重分形特征

应用分形和多重分形理论研究了负载型聚乙烯催化剂(简称催化剂)表面形态。提出一种图片处理和计算过程更加完备的基于扫描电子显微镜照片的分形维数和多重分形谱计算程序,对4种催化剂进行分析计算。探讨了分形维数、多重分形谱相关参数与催化剂表面形态及与聚合活性的对应关系。实验结果表明,催化剂表面形态的复杂程度可以用表面分形维数来表征,聚合活性高的催化剂表面形态更加复杂,有更大的比表面积,对应的分形维数值也越大。催化剂表面分形维数的变化程度可以用多重分形谱来表征,聚合活性高的催化剂表面分形维数的跨度和分散程度更高。提出的分形维数和多重分形谱计算程序为催化剂的评定与设计提供了一种实用的手段。     

Effect of select parameters on the properties of edible film from water-soluble fish proteins in surimi wash-water

Edible film from water-soluble fish proteins were developed by casting film solution on leveled trays and effects of pH (9.5, 10.0 and 10.5), heating temperature (60, 70 and 80 °C), and heating time (10, 20 and 30 min) of the film solution on various film properties were determined using Response Surface Methodology (RSM). The impact of pH and heating temperature of film solution was more significant, overall, on the film's properties than heating time. Contour plots of tensile strength and elongation at break was highest at pH of 10.0 at 70 °C (2.75-3.02 MPa) but low in elongation at break (6.35-9.16%), while water vapor permeability and oxygen permeability were at their lowest (58.55-65.96 g mm/m² d kPa and 351.33-624.18 cm³ μm/m² d kPa). There was a direct correlation between the films’ and proteins’ solubility on one hand, and heating temperature of film solution on the other, which reversed with change in pH of film solution. Film color was darker and more yellowish with increase in the pH of film solution.     

某住宅小区边坡渗水治理及综合利用

分析了某小区边坡渗水的原因，结合实际情况，介绍了边坡渗水的治理措施，并对渗水进行了收集综合利用，消除了边坡滑坡的安全隐患，取得了较好的社会效益和经济效益。     

等离子体刻蚀工艺控制模型分析

讨论了主因素分析法以及神经网络法在等离子体刻蚀工艺中的应用.结果表明主元素分析法可以实现对数据的压缩,而神经网络算法则显示出比传统的统计过程控制算法更好的准确性.     

磁电雾化电晕放电低温等离子体及其应用

本文讨论了磁电雾化电晕放电低温等离子体技术的基本原理,以及它在静电除尘、烟气脱硫等环保生物工程等领域中的应用前景.     

Pilot Plant Study of Simultaneous Sewage Sludge Digestion and Metal Leaching

This research is related to a preindustrial pilot scale study of the performance of the simultaneous sewage sludge digestion and metal leaching (SSDML) process for decontamination and stabilization of sewage sludge. Ten batch tests were carried out in two 4?m3 bioreactors under various conditions of operation. Results indicated that the addition of 1.0 to 1.5?g?S0/L, which is the equivalent of approximately 30 to 50?kg?S0 per tons dry sludge, is sufficient to obtain conditions of acidity (pH<2.5) and oxido-reduction potential greater than 500 mV necessary for an effective solubilization of toxic metals. The final average of metal solubilization in the output sludge during the SSDML process varied in the following ranges: 25–78% Cd, 9–32% Cr, 48–100% Cu, 77–99% Mn, 15–53% Ni, 12–47% Pb, and 66–100% Zn. The N, P, and K contents were also preserved in the decontaminated sludge. Moreover, the use of low concentrations of elemental sulfur makes it possible to obtain decontaminated sludge with a low total sulfur content (1.4–1.5% S) compatible with agricultural use. The suspended solids removal calculated for the SSDML process was slightly lower, (2.5±0.4)% volatile suspended solids per day, than those reached using standard aerobic digestion. Finally, the SSDML process was found to be effective in removing bad odors and in the destruction (99–100%) of indicator bacteria.     

新型高K栅介质ZrO2薄膜材料的制备及表征

采用超高真空电子束蒸发法制备了新型高 K栅介质-非晶 ZrO2薄膜. X射线光电子能谱 (XPS) 中 Zr3d5/2 和 Zr3d3/2 对应的结合能分别为 182.1eV和 184.3eV, Zr元素的主要存在形式为 Zr4+,说明薄膜由完全氧化的 ZrO2组成 ,并且纵向分布均一.扩展电阻法( SRP)显示 ZrO2薄膜的 电阻率在 108Ω@ cm以上,通过高分辨率透射电镜( HR- XTEM)可以观察 ZrO2/Si界面陡直,没有 界面反应产物 ,证明 600℃快速退火后 ZrO2薄膜是非晶结构.原子力显微镜( AFM)表征了薄膜的 表面粗糙度,所有样品表面都很平整,其中 600℃快速退火样品 (RTA)的 RMS为 0.480nm.     

润滑油用纳米TiO2的表面改性及自修复性能研究

采用油酸对纳米TiO2进行表面改性，使其稳定分散于基础油中。利用HQ-1摩擦磨损试验机考察纳米TiO2的自修复性能，并探讨其自修复机理。试验结果表明，经改性后的纳米TiO2粉体作为润滑添加剂具有良好的分散稳定性、减摩抗磨性和自修复性。     

纳米ZrO2等离子涂层的结构,性能和工艺特点

采用大气等离子喷涂技术(APS)，制备了常规氧化锆和纳米结构氧化锆两种涂层．利用扫描电镜(SEM)对涂层的显微结构进行了观察．对两种涂层的沉积效率、表面粗糙度和显微硬度作了对比研究．结果表明，粉末原料的显微结构、粒度、形态、喷涂工艺参数(喷涂功率和距离)对涂层的显微结构有较大的影响．等离子喷涂造粒纳米氧化锆粉制备的涂层沉积效率高而稳定，其显微结构与喷涂功率和距离密切相关．与常规氧化锆涂层相比，纳米结构氧化锆涂层具有较高的显微硬度和较低的表面粗糙度．     

高斜效率高功率850nm氧化限制型垂直腔面发射激光器

报道了MOCVD生长的高性能850nm氧化限制型垂直腔面发射激光器.研制出的氧化直径为9μm的激光器25℃时的斜效率和阈值电流分别为0.82mW/mA和2.59mA,激光器在23mA时输出16mW最大光功率.氧化直径为5μm的激光器25℃时的最小阈值电流为570μA,其最大饱和光功率为5.5mW.