热压烧结制备Cu/FeCoCr复合材料的显微组织及热物理性能

利用相图计算的CALPHAD方法和超音雾化制粉技术,在CuFeCoCr体系中设计并制备了一系列微米级复合粉体。通过热压烧结方法在烧结温度为950℃,烧结压力为45 MPa的工艺条件下成功获得块体复合材料。研究了块体复合材料中Cu含量对显微组织,热导率,热膨胀系数以及显微硬度的影响。结果表明:CuFeCoCr块体复合材料均由fcc富铜相和fcc富铁钴铬相组成。该系列复合材料经600℃时效处理8 h后,其热膨胀系数变化范围为5.83×10-6~10.61×10-6 K-1,热导率变化范围为42.17~107.53 W·m-1·K-1。其中Cu55(Fe0.37Cr0.09Co0.54)45复合材料表现出良好的综合性能,即其热膨胀系数和热导率分别为9.08×10-6K-1和91.09 W·m-1·K-1,与电子封装半导体材料的热膨胀系数相匹配。     

浅水油气田开发水下干式采油装置

针对我国浅水海域敏感区、航道等受限区域的油气田难以实现经济有效开发的问题，借鉴港口工程行业成熟的大直径钢圆筒技术，结合常规水下干式舱及常规油田处理工艺技术，开展水下干式采油装置技术研究并形成方案，其投资较常规水下生产系统显著降低，可进一步提高受限油气田开发的经济收益，对推动浅水受限油气田开发具有重要意义。     

电磁精细探测法在隐伏型导水地质裂缝勘探中的应用

针对传统隐伏型导水地质裂缝勘探方法存在勘测精度较差的问题,提出电磁精细探测法探析隐伏型导水地质裂缝。依照屏蔽系数、实测场强和理论场强数据绘制综合曲线图,通过该图获取隐伏型导水地质裂缝所处位置几何阴影范围,采用层析成像法得到网格化的工作面,获取隐伏型导水地质图像。通过图像直接观测隐伏型导水地质工作面裂缝所处位置,在此基础上,观测四个电磁场分量,采用正交电磁场分量计算介质视电阻率,依据计算视电阻率数值和视电阻率分布状态研究裂缝发育情况和裂缝富水程度。结果表明:采用该方法能较为精准地获取隐伏型导水地质裂缝位置。通过裂缝位置进一步检测出隐伏型导水地质裂缝最大发育高度为63.5 m。当视电阻数值不断增加时,隐伏型导水地质裂缝和裂缝富水性逐渐减小,与实际情况较为相符,说明该种方法探析效果较好。     

粉末注射成型技术的研究和应用

介绍了粉末注射成型技术的概念和工艺,包括金属粉末注射成型(MIM)、陶瓷粉末注射成型(CIM),讲述了黏结剂的使用发展情况;阐述了粉末注射成型专用注射成型机的特点,PIM粉末注射专用塑化系统,PIM专用料斗滑块装置,镶套式机筒座等,介绍了PIM技术在诸多行业中的应用,3C行业,医疗行业,汽车行业等,并展望了PIM研究的发展方向。     

萃取塔数学模型及过程强化的若干研究进展

萃取塔因生产能力大、占地面积小、密闭性好等优点，在石油、化工、生物、医药和环境工程等多领域被广泛应用。本文从以下几个方面介绍了萃取塔近些年的研究进展：综述了传统萃取塔（脉冲萃取塔、转盘塔与Kühni塔等）的水力学、轴向扩散与传质模型的发展，分析比较了表面张力、传质方向、放大效应等因素对模型的影响；介绍了计算流体动力学（CFD）在萃取塔中单液滴、单相流模拟、液-液两相流模拟、外加能量模拟、与群体平衡模型（PBM）耦合模拟中的应用进展；介绍了国内外设计开发的新型萃取塔，包括改变传统塔的内构件和引入多种外场能量等方式来强化相间传质。研究表明，将先进实验研究方法、准确经验模型和可靠理论计算相结合，将会是萃取塔研究的重要手段和方向。     

Enhanced dielectric and piezoelectric properties in Na0.5Bi4.5Ti4O15 ceramics with Pr-doping

The bismuth layer-structured Na_0.5Bi_4.5-xPr_xTi₄O₁₅ (x?=?0, 0.1, 0.2, 0.3, 0.4, and 0.5) (NBT-xPr³⁺) ceramics were fabricated using the traditional solid reaction process. The effect of different Pr³⁺ contents on dielectric, ferroelectric and piezoelectric properties of Na_0.5Bi_4.5Ti₄O₁₅ ceramics were investigated. The grain size of Pr³⁺-doping ceramics was found to be smaller than that of pure one, the maximum dielectric constant and Curie temperature T_c gradually decreased with increasing Pr³⁺ contents, and the dielectric loss decreased at high temperature by Pr³⁺-doping. Moreover, the activation energy (E_a), resistivity (Z’), remanent polarization (2P_r) and piezoelectric constant (d₃₃) increased by Pr³⁺-doping. The NBT-xPr³⁺ ceramics with x?=?0.3 achieved the optimal properties with the maximum dielectric constant of 1109.18, minimum loss of 0.00822 (250?kHz), E_a of 1.122?eV, Z’ of 7.9?kΩ?cm (725 ºC), d₃₃ of 18 pC/N, 2P_r of 12.04 μC/cm². The enhancement was due to the addition of Pr³⁺ which suppressed the decreasing of resistivity at high temperature and made it possible for NBT-xPr³⁺ ceramics to be poled in perpendicular direction, implying that it is a great improvement for Na_0.5Bi_4.5Ti₄O₁₅ ceramics in electrical properties.     

Formation mechanism of elongated β–Si3N4 crystals in Fe–Si3N4 composite via flash combustion

Elongated β–Si₃N₄ crystals have a significant influence on the mechanical property of Fe–Si₃N₄ composite. In this paper, the formation mechanism of elongated β–Si₃N₄ crystals in Fe–Si₃N₄ composite was investigated. During the preparation process, β–Si₃N₄ crystals developed in a spiral and layer growth mechanism in the dense areas. They kept growing from the dense areas and formed radially distributed elongated crystals with hexagonal prismatic morphology as time went on. As for the formation mechanism, the (100) crystal plane of β–Si₃N₄ from Si-N-O melt is mainly the vicinal crystal planes growth with different angles from the (100) crystal plane. At the later stage, the crystallization and the diffusion forces in Si-N-O molten phase decreased. However, the short range diffusion remained active and resulted in the gradient distribution of N content near the boundary. With the temperature decreasing, the disappearance of the short range diffusion implied the end of the crystallization process of the elongated β–Si₃N₄ crystals.