VO2/GaAs异质结的制备及其光电特性研究

采用直流磁控溅射和后退火氧化工艺在p型GaAs单晶衬底上成功制备了n-VO_2/pGaAs异质结,研究了不同退火温度和退火时间对VO_2/GaAs异质结性能的影响,并分析其结晶取向、化学组分、膜层质量以及光电特性。结果表明,在退火时间2 h和退火温度693 K下能得到相变性能最佳的VO_2薄膜,相变前后电阻变化约2个数量级。VO_2/GaAs异质结在308 K、318 K和328 K温度下具有较好的整流特性,对应温度下的阈值跳变电压分别为6.9 V、6.6 V和6.2 V,该结果为基于VO_2相变特性的异质结光电器件的设计与应用提供了可行性。     

Complete Photochemical Regulation of 8–17 DNAzyme Activity by Using Reversible DNA Photo-crosslinking

The regulation of DNAzyme activity is an important problem for its in vivo applications. We achieved photochemical regulation of DNAzyme activity by using reversible DNA photo-crosslinking of 3-cyanovinylcarbazole (^CNVK). The ODN containing ^CNVK photo-crosslinked to a pyrimidine base in the complementary strand after a few seconds of photoirradiation, and its photoadduct was split by photoirradiation of another wavelength. The activity of photo-crosslinked DNAzyme with ^CNVK was completely inhibited (OFF state). In contrast, after 312 nm irradiation, DNAzyme activity was recovered upon addition of a substrate strand (ON state). In addition, the photo-crosslinked DNAzyme is prone to enzymatic digestion by exonuclease. This photochemical OFF to ON switching with reversible DNA photo-crosslinking was regulated at the desired time and position; therefore, it might be possible to use it for in vivo application.     

A New Design Methodology for Time-Based Capacitance-to-Digital Converters (T-CDCs)

This paper introduces a 9-bit time-based capacitance-to-digital converter (T-CDC). This T-CDC adopts a new design methodology for parasitic cancellation with a simple calibration technique. In T-CDCs, the input sensor capacitance is first converted into a delay pulse using a capacitance-to-time converter (CTC) circuit; then this delay signal is converted into a digital code through a time-to-digital converter (TDC) circuit. A prototype of the proposed T-CDC is implemented in UMC 0.13 μm CMOS technology. This T-CDC consumes 8.42 μW and achieves a maximum SNR of 45.14 dB with a conversion time of 1 μs that corresponds to a figure of merit (FoM) of 16.4 fJ/Conv.     

Robust Metallic Actuators Based on Nanoporous Gold Rapidly Dealloyed from Gold–Nickel Precursors

Dealloyed nanoporous gold (np-Au) has applications as oxygen reduction catalysis in Li-air batteries and fuel cells, or as actuators to convert electricity into mechanical energy. However, it faces the challenges of coarsening-induced structure instability, mechanical weakness due to low relative densities, and slow dealloying rates. Here, monolithic np-Au is dealloyed from a single-phase Au₂₅Ni₇₅ solid-solution at a one-order faster dealloying rate, ultra-low residual Ni content, and importantly, one-third more relative density than np-Au dealloyed from conventional Au₂₅Ag₇₅. The small atomic radius and low dealloying potential of the sacrificing element Ni are intrinsically beneficial to fast produce high relative density np-Au, as predicted by a general model for dealloying of binary alloys and validated by experiments. Stable, durable, and reversible actuation of np-Au takes place under cyclic potential triggering in alkaline and acidic electrolytes with negligible coarsening-induced strain-shift. The thermal and mechanical robustness of bulk np-Au is confirmed by two-order slower ligament coarsening rates during annealing at 300 °C and 45 MPa macroscopic yielding strength distinctive from the typical early onset of plastic yielding. This article opens a rich direction to achieve high relative density np-Au which is essential for porous network connectivity, mechanical strength, and nanostructure robustness for electrochemical functionality.     

DR环形吹风冷却装置及智能控制系统设计研究

介绍了河北达瑞化纤机械有限公司开发的DR环形吹风冷却装置,该装置能实现自动、精准、快速更换整流筒,打破了原有环吹风装置整流筒从风室顶部安装这一传统模式,利用风室底部安装和风室密封结构改变,采用气缸动力下的自动调节技术,实现了快速更换整流筒。该装置在维修和更换整流筒组件时,无须搬动上压盖,无须拆装若干螺栓,能自动化操作,降低了操作工人劳动强度,缩短了操作时间。开发的DCS智能控制系统,实现了实时智能监测冷却吹风装置的运行状况。     

可逆感温变色聚丙烯专用料的制备及性能

通过两步法制备可逆感温变色聚丙烯（PP）专用料，首先将乙烯-辛烯共聚物（POE）与可逆感温变色粉于微型双螺杆挤出机中挤出造粒制备色母料，然后将PP与色母料熔融共混挤出制备可逆感温变色PP专用料。探讨了色母料含量对PP专用料感温变色性能、力学性能、热学性能及微观形貌的影响。结果表明，利用POE与PP良好的相容性，实现了可逆感温变色粉在PP基体中均匀的分散，可逆感温变色PP专用料表现出优异的可逆感温变色性能和冲击性能。     

Iron Loss Calculation of AC Filter Inductor for Three‐Phase PWM Inverters

In recent years, remarkable advancement of new power semiconductor devices, such as SiC and GaN, enables the increase of switching frequency of power converters, and hence the volume of passive components, such as ac filters and transformers, can be reduced. However, temperature rise caused by the inductor loss is increasing, and hence iron loss evaluation of the inductor is one of the most important issues to realize high power density converters. Conventionally, an improved generalized Steinmetz equation (iGSE) has proposed in order to calculate the iron loss under a pulse voltage magnetizing condition. However, accurate iron loss calculation of the ac filter inductor used in a PWM inverter cannot be realized. The authors have proposed two methods of iron loss evaluation of ac filter inductors. The first one is a loss map method which can calculate the iron loss without using a real PWM inverter. Another one is an ILA (Inductor Loss Analyzer) which can measure the iron loss in every switching period in a real PWM inverter. In this paper, comparisons of the iron loss between the ILA and the loss map method on both the single‐phase and three‐phase inverters are studied. It is found that iron loss of the ac filter inductor in the three‐phase PWM inverter which is calculated by the loss map method cause a large error on a specific condition. In order to prevent the calculation error, the authors proposed a revised loss map method and proved the effectiveness of the method.     

Integrated circuit and system design for renewable energy inverters

This study proposes that a novel integrated circuit (IC) and system design for renewable energy inverters can harvest renewable energy to power direct current (DC) and alternating current (AC) loads. In addition, an intelligent synthesis and management tool is developed to design the proposed system and to judge the system’s operational maintenance decisions. Finally, a renewable energy inverter’s information is posted to an online system. Users can obtain the proposed system’s information at any time and place. The accurate and superior performance of the proposed IC and system is confirmed by computer simulations and experimental results.     

Investigation on SCR-based ESD protection device for biomedical integrated circuits in a 0.18-μm CMOS process

In these decades, integrated circuits for biomedical electronics applications have been designed and implemented in CMOS technologies. In order to be safely used by human, all microelectronic products must meet the reliability specifications. Therefore, electrostatic discharge (ESD) must be taken into consideration. To protect the biomedical integrated circuits in CMOS technologies from ESD damage, a dual-directional silicon-controlled rectifier (DDSCR) device was presented in this work. Experimental results show that the DDSCR has the advantages of high ESD robustness, low leakage, large swing tolerance, and good latchup immunity. The DDSCR was suitable for ESD protection in biomedical integrated circuits.