多模态影像学检查在诊断早期强直性脊柱炎骶髂关节疾病中的效果

目的:探究在早期强直性脊柱炎骶髂关节疾病诊断中不同放射影像学检查方法的应用效果。方法:抽取2018年5月-2020年1月本院收治的早期强直性脊柱炎骶髂关节疾病患者65例作为研究对象,所有患者均开展X线、CT、MRI影像学检查,对比三种不同影像学检查方法的检出率、影像学特征。结果:X线、CT、MRI检出率分别为38.46%(25/65)、60.00%(39/65)、76.92%(50/65),检出率相比,MRI、CT明显高于X线,P<0.05;X线、CT、MRI影像学特征,发现关节间隙出现不同的异常,如关节面出现侵蚀、骨质囊变现象,关节面下骨质出现硬化与关节软骨出现肿胀,其中MRI、CT检查,阳性率高于X线,P<0.05。而对于软组织肿胀、骨髓水肿、滑膜炎症、关节滑膜增厚等现象,只能通过MRI检查才能诊断。结论:在早期强直性脊柱炎骶髂关节疾病诊断中,X线、CT、MRI影像学检查均具有一定的指导意义,而MRI不仅可以提高检出率,还能准确反映微小病灶及其软组织病变,对于早期发现骶髂关节炎值得推荐。     

Inconel 690传热管GTAW对接焊接头组织及力学性能研究

对Inconel 690传热管材进行钨极气体保护焊(GTAW)对接焊,采用拉伸试验机、压扁试验机和光学显微镜测试和分析传热管焊接接头,同时利用ANSYS软件开展焊接接头在设计工况失压时的一次应力强度校核。研究结果表明:焊缝中心为树枝胞状晶,熔合线附近为粗大柱状晶。室温时接头的平均抗拉强度为619 MPa,平均屈服强度为292 MPa,350℃时接头平均抗拉强度为475 MPa,平均屈服强度为206 MPa,拉伸接头断裂从熔合区开始贯穿整个焊缝组织,呈塑性断裂。压扁试验和反向压扁试验结果表明管接头完好。通过ANSYS分析可知,设计工况下传热管接头350℃许用应力强度150 MPa限值可满足其一次应力强度要求,且裕量较大。     

高应力软岩巷道锚注一体化联合支护技术应用

介绍了国家专利注锚剂、中空注浆锚索等产品,以国家能源麦朵山煤矿11采区2煤辅助运输巷为研究对象,采用数值模拟、理论分析、现场测试及井下试验相结合的综合研究方法,对11采区2煤辅助运输巷采用锚注一体联合支护技术,来实现对岩体裂隙注浆,使浆料与岩体结为一体,在围岩与支护体共同作用过程中,实现强岩增荷的作用,维护巷道的稳定性,实现工作面的安全生产。     

低压静电场辅助冷冻对竹笋品质的影响

为研究低压静电场辅助冷冻对竹笋冻结特性的影响，以冻结曲线、硬度、水分损失率、水分迁移、冰晶形态和组织微观结构为指标，探究低压静电场辅助冷冻（－35 ℃）和普通冷冻（－35 ℃）条件下竹笋品质的变化规律。结果表明：低压静电场辅助冷冻提高了冻结效率，改变了冰晶形态及分布，减轻了组织微观结构破损程度，改善了解冻汁液流失情况。与静电板间距10、20、30、40 cm处的冷冻竹笋解冻后水分损失率分别为14.16%、12.58%、9.73%、10.44%，显著低于对照组（21.01%）（P＜0.05），硬度分别为461.19、507.48、496.65 g和455.31 g，显著高于对照组（350.70 g）（P＜0.05）。低场核磁共振分析结果表明，在低压静电场辅助冷冻下竹笋解冻后汁液流失减少，扫描电子显微镜观察结果显示，竹笋纤维排列整齐，组织微观结构保持较好。低压静电场辅助冷冻可有效改善竹笋品质，可为利用低压静电场进行果蔬的冷冻贮藏和冷链运输提供参考。     

智能假肢膝关节的研发要点及其研究进展综述

目的 介绍国内外智能假肢膝关节研究的主要进展,为相关领域的研发提供可借鉴的思路.方法 基于机械结构、调控方式、驱动方式,对典型假肢膝关节进行了分类比较,并从假肢穿戴者的运动意图识别、驱动控制、人机协调控制等方面做了分析.此外,对假肢膝关节在智能化研究与安全性、个性化与通用性、人机共融技术、科学伦理、关键技术等方面需要注意的问题,提出了研发要点和技术思路.结论 智能假肢膝关节应注重安全性与稳定性,规避用户在使用过程中的潜在危险因素;实现假肢控制参数的自整定和灵活适配,在个性化与通用性上达到平衡;综合考虑人—机—环境因素,实现协调控制;坚持"以人为本",在技术方法和科学伦理两个方面开展医工结合的研究;突破关键技术限制,建立完善的社会医疗康复保障服务体系.     

Novel silicon-contained lignin-based carbon fibers derived from bamboo pulping black liquor with improved electrochemical performance for supercapacitors

Carbon fibers (CFs) are a promising candidate as electrode materials for flexible supercapacitors given its light weight and moderate cost. In this study, the lignin used was partially separated from kraft bamboo pulping black liquor and the higher molecular weight fraction, unavoidably contains a small amount of silicon compounds, so named silicon-contained lignin. Novel CFs were prepared using commercial polyacrylonitrile (PAN) and the lignin by electrospinning and further carbonization. Even in the presence of silicon compounds, the fibrous morphology of precursor fibers was significantly good, and the CFs with uniform fiber diameter and high specific surface area up to 182 m²/g were obtained with an increase in silicon-contained lignin. The CFs fabricated from silicon-contained lignin and commercial PAN had higher specific capacitance (22.20 mF/cm² at 10 mA/cm²) and superb cycling stability (94.21%) than that from silicon-free lignin or pure PAN separately.     

Stress wave propagation in adhesively bonded functionally graded cylinders: an improved model

This study presents an improved mathematical model to analyse the stress wave propagation in adhesively bonded functionally graded (FG) circular cylinders (butt joint) under an axial impulsive load. The volume fractions of the material constituents in the upper and lower cylinders were functionally tailored through the thickness of each cylinder using a power-law. The effective material properties of both cylinders, which are made of aluminum (Al) and silicon carbide (SiC), at any point were predicted by using the Mori–Tanaka homogenization scheme. In this improved model, the governing equations of the wave propagation include the spatial derivatives of local mechanical properties and were discretized by means of the finite difference method. The influence of these spatial derivatives and the compositional gradient exponent on the displacement and stress distributions of the joint was investigated. The material composition variations of both cylinders affected the displacement and stress fields whereas the compositional gradient exponent had a minor effect. The stress concentrations were alleviated in time, the displacement and stress distributions/variations around/along the upper and lower cylinder-adhesive interfaces were significantly affected by the adhesive layer. The spatial derivatives also affected the temporal histories of the displacement and stress components evaluated at the selected critical points of the upper cylinder, adhesive layer and lower cylinder. The consideration of the spatial local material derivatives provided a more accurate mathematical model of wave propagations through the graded layered structures.     

动态高压微射流处理对方竹笋膳食纤维理化及结构特性的影响

以方竹笋中提取的膳食纤维为研究对象，采用动态高压微射流（dynamic high-pressure micro-fluidization, DHPM）在不同压力条件（0，50，100，150，200 MPa）下进行处理，探究其对竹笋膳食纤维（bamboo shoots dietary fiber, BSDF）理化和结构特性的影响。结果表明，随着处理压力的增大，BSDF粒径先增大后减小，当处理压力为150 MPa时，粒径最小，为（370±11） nm，此条件下BSDF的持水力、持油力和膨胀力达到最大，较对照组分别提高了47.74%，50.54%，61.27%，且差异显著（P<0.05）。红外光谱分析表明DHPM处理不会改变BSDF的官能团，但会使BSDF内部的部分氢键断裂和半纤维素、木质素等发生降解；X射线衍射和热重分析表明DHPM处理不会引起BSDF的晶体结构改变，但晶体有序度会下降，进而导致其热稳定性降低；微观结构分析显示DHPM处理会使BSDF颗粒尺寸减小、表面粗糙、组织松散，且当处理压力为200 MPa时，颗粒发生团聚。综上，DHPM可以有效改善BSDF的理化性质，在膳食纤维改性方面具有一定的应用价值。     

New insights into microstructural changes during transient liquid phase bonding of GTD-111 superalloy

The effects of joining temperature (T_J) and time (t_J) on microstructure of the transient liquid phase (TLP) bonding of GTD-111 superalloy were investigated. The bonding process was applied using BNi-3 filler at temperatures of 1080, 1120, and 1160 °C for isothermal solidification time of 195, 135, and 90 min, respectively. Homogenization heat treatment was also applied to all of the joints. The results show that intermetallic and eutectic compounds such as Ni-rich borides, Ni−B−Si ternary compound and eutectic-γ continuously are formed in the joint region during cooling. By increasing t_J, intermetallic phases are firstly reduced and eventually eliminated and isothermal solidification is completed as well. With the increase of the holding time at all of the three bonding temperatures, the thickness of the athermally solidified zone (ASZ) and the volume fraction of precipitates in the bonding area decrease and the width of the diffusion affected zone (DAZ) increases. Similar results are also obtained by increasing T_J from 1080 to 1160 °C at t_J=90 min. Furthermore, increasing the T_J from 1080 to 1160 °C leads to the faster elimination of intermetallic phases from the ASZ. However, these phases are again observed in the joint region at 1180 °C. It is observed that by increasing the bonding temperature, the bonding width and the rate of dissolution of the base metal increase. Based on these results, increasing the homogenization time from 180 to 300 min leads to the elimination of boride precipitates in the DAZ and a high uniformity of the concentration of alloying elements in the joint region and the base metal.     

竹材液化墙体泡沫材料的阻燃改性

为提高竹材液化产物所制备的高轻发泡墙体材料的防火性能，分别采用材料内部添加和表面浸泡的方法进行阻燃改性，并评价不同阻燃剂及其添加量对发泡材料阻燃性能的影响。实验结果表明：在材料内部或表面添加选择的阻燃剂不会对材料自身形貌或组分产生明显影响，对材料的力学性能亦不会造成破坏，在材料内部添加3 g膨胀型凝胶-二氧化硅/聚磷酸铵核壳阻燃剂（MCAPP）后压缩强度达到了0.37 MPa，在材料表面浸泡聚硅氧烷后压缩强度达到了0.58 MPa，同时能提高材料的阻燃性能，在材料内部添加聚磷酸铵（M-APP）后极限氧指数提高到33.2%，比改性前提高3%。在材料表面浸泡膨胀型壳聚糖-蒙脱土-聚磷酸铵（CMAp）后点燃时间明显延长，极限氧指数最高达到了31.5%。