新型AMBBR-MBBR-MBR工艺处理紫外线吸附剂厂废水

根据传统工艺处理紫外线吸附剂厂UV-P废水中高级氧化作为预处理成本高,单一A₂O生化工艺出水不稳定,并且出水污染物浓度高等缺点,首先采用零价铁强化水解和预曝气作为预处理,以新型AMBBR-MBBR-MBR工艺进行处理。工程MBBR采用三维多孔泡沫陶瓷填料为生物载体,MBR采用Si O₂平板陶瓷膜。长期调试运行效果表明,出水水质优于≤城镇污水处理厂污染物排放标准≥GB 18918-2002表1中一级A标准,即COD<50 mg/L,氨氮<5 mg/L,总氮<15 mg/L,硝基苯<2.0 mg/L,挥发酚<0.5 mg/L,苯胺类<0.5 mg/L等。水处理运行费用为4.9元/m³。     

新型纳米平板陶瓷膜在纸箱生产废水回用中的工程应用

采用混凝沉淀+水解酸化+MBR+活性炭吸附组合工艺来回用纸箱厂废水。MBR膜采用的是新型纳米平板陶瓷膜。介绍了各处理段的工艺特点、构筑物的设计尺寸、设备选型等,并对新型纳米平板陶瓷膜的清洗进行了介绍。系统运行一年,出水水质稳定,优于≤城市污水再生利用城市杂用水水质≥GB/T 18920-2002表1中的城市绿化排放标准,即BOD5≤20 g/L,浊度≤10 NTU,色度≤30,并分析了本工程的处理成本及所产生的经济效益。     

电脑横机编织三维全成形口罩结构建模与工艺实践

为探究用电脑横编机开发全成形针织产品的可能性,以针织三维全成形口罩为开发对象,进行结构建模与工艺实践。首先对人体面部尺寸进行测量,以此确定全成形口罩的二维纸样;然后结合全成形口罩规格尺寸进行工艺计算,以四针床电脑横编机和SDS-ONE APEX3系统为开发工具,分别建立针织三维全成形口罩的口罩主体、过滤垫片口袋开口、挂耳带部位的结构模型。结果表明:通过对口罩的规格设计并建立结构模型,同时结合工艺参数的调节并优化其生产技术,可实现兼具美观性与舒适性三维全成形口罩的快速生产,结合功能性原料可开发高附加值的口罩产品。     

直纺亮光抗倒伏波浪扁平涤纶FDY的开发

探讨了直纺83 dtex/114 f波浪扁平涤纶全拉伸丝(FDY)的工艺制备过程。试验证明,在熔体输送温度276~282℃,纺丝温度286~290℃,喷丝板规格DIO φ104 mm-114孔、"王"字形,环吹风压10~15 Pa,含油率1.1%~1.2%,卷绕速度3 800~4 200 m/min的工艺参数下纺制83 dtex/114 f波浪扁平涤纶FDY时,生产稳定,满卷率高,外观情况良好,袜带均匀亮丽,可批量生产。此新产品可用于制作高档布艺沙发表层面料,具有抗倒伏、色彩艳丽等功效。     

大直径平底负压容器优化设计

通过对大直径平底负压容器平底板的设计计算,平底板计算厚度很厚。通过分析,提出了对平底板采取加强措施,从而减薄平底板计算厚度的方法。该容器在实际生产过程中性能可靠、稳定,对类似设备设计具有借鉴意义。     

采油树平板闸阀柔性密封圈结构优化设计

为了提高采油树平板闸阀密封圈的密封性能,在泛塞封的基础上,设计一种密封圈本体唇边开有锯齿状凸起的新型柔性密封结构;运用有限元分析方法模拟密封圈的工作状况,分析柔性密封结构特性参数对密封圈密封性能的影响,获得不同柔性密封圈结构参数下密封面间接触应力分布规律,并对新型密封结构进行优化。结果表明:密封面间最大接触应力随唇边锯齿数量、唇边夹角度数的增大而增大,随唇谷夹角度数的增大而减小;新型密封结构选择锯齿数量为3、唇边夹角为20°、唇谷夹角为30°的特性参数时,其最大接触应力比常规Y形密封圈提高了15倍;新型柔性密封结构的密封圈与阀杆、阀盖壁面间接触应力比常规Y形密封圈有显著提高,提高了密封圈的密封性能。     

Receding horizon time-optimal control for a class of differentially flat systems

A closed-loop, time-optimal path-following control scheme is proposed for a class of constrained differentially flat systems. Within a receding horizon framework, a finite horizon optimisation problem is solved at each sample, using available state feedback and feedforward path information. Irrespective of horizon length, the proposed formulation guarantees exact path-following. Moreover, the requirements under which the proposed algorithm achieves minimum-time path-following are established. Simulations conducted with a rigid X–Y table model confirm the theoretical results.     

Constructal design of flat tubes cooled by natural convection

A set of vertical flat tubes cooled by natural convection and placed in a finite size space is designed based on the constructal law. The constraint in this design is the size of the space where the tubes are placed. The freedom inside the space is the distance between the tubes. When the constructal law is applied, the optimal distance between the tubes is determined. Rayleigh numbers are taken as (Ra = 10³, 10⁴, and 10⁵). The dimensionless tube diameter (tube diameter/tube height) is changed from (D* = 0.2) to (D* = 1) (circular tube). All the tubes are heated to the same wall temperature. The air used to cool the tubes has a Prandtl number (Pr = 0.72). The equations of conservation of mass, momentum, and energy for steady, two-dimensional, and incompressible flow are solved by the finite volume method. The result showed that the best or optimal distance at a given Rayleigh number remains constant for all tube diameters. The result also showed that the number of the small diameter tubes must be more than the number of the large-diameter tubes for the same Rayleigh number and the same size of the space to make the heat flow from the tubes to the coolant easier.     

Microstructure and mechanical behavior of Ti/Cu/Ti laminated composites produced by corrugated and flat rolling

Ti/Cu/Ti laminated composites were fabricated by corrugated rolling (CR) and flat rolling (FR) method. Microstructure and mechanical properties of CR and FR laminated composites were investigated by scanning electron microscopy, numerical simulation methods, peel and tensile examinations. The effect of CR and FR was comparatively analyzed. The results showed that the CR and FR laminated composites exhibited different effective plastic strain distributions of the Ti layer and Cu layer at the interface. The recrystallization texture, prismatic texture and pyramidal texture were developed in the Ti layer by CR, while the R-Goss texture and shear texture were developed in the Cu layer by CR. The typical deformation texture components were developed in the Ti layer and Cu layer of FR laminated composites. The CR laminated composites had higher bond strength, tensile strength and ductility.